thank u for this vid. It really helped me understanding the function of different mosfets and selecting the right mosfet for a power source selection switch.

As I usually say, years of un-understood lectures in college just easily explained by a short video, thank you!

أشكرك وأقدر مجهودك ، تحياتي لك من تركيا.

Great explanation. But here's some input for your explanation. BMS works on each series from the batteries. It can't control on each batteries on one parallel configurarion. So it's more relevant if you create the animation for your video on series connection instead of parallel connection

What about a voltage follower inplace 🤔

I have a question about the rise fall time how to reduce it ?

Nice expln

thank u sir, but please remove extra sound,

Hello. Thank you for great job. Could you please explain the solenoid valve control where you can measure bias when the connector is disconnected?

Master put address to I2C bus. Then corrosponding slave identify and match with his own address . Then slave say Hi to master ( send ACK to master) How slave match address which is send by master . Which register compare received address and its own address . Thanks.

Master put address to I2C bus. Then corrosponding slave identify and match with his own address . Then slave say Hi to master ( send ACK to master) How slave match address which is send by master . Which register compare received address and its own address . Thanks.

Nice Video, Thank you for providing more clear about Bus Arbitration tech.

Thank you very much

nice video!

How gated clock disable the other slaves , please explain in detail

In which time it boosts the voltage, In which time it will act as buck converter, like while MOSFET switch is ON time or OFF time

When Cr is discharging around time t7, u r saying that magnetizing current flows in the opposite direction but in the waveform Im is still in positive region even though it is decreasing. so which means direction is not reversed yet for Im, and the energy it has would be going where???? is it circulating in the path of primary winding and magnetizing inductor?

What pins do we connect to the input signal/voltage and what pins do we connect to the mosfet ??

if Vgs = Vds at some point in your graph then will not my MOSFET die? because Vds tends to 100V and Vgs around 5v i didnt understand or maybe its silly to ask but please rectify it

how to make it controller using arduino atmega, or esp8266 micro controller ?

For BJT totem pole Vcc is correct name of supply voltage,c-collector.Vdd for mosfets.For correct work of mosfet totem pole RD circuit in gate supply needed for different rise/fall times to prevent shoot through

your animation is superb in understanding the actual happening inside the devices, i gone through all your serial communication protocols all are well explained :)

😂😂❤❤❤

great video

do you have SOC algorithm code and model for lithium ion battery

8 Parallel mosfet in 20khz 60vdc? Drive?

Too bad the manufacturers get away with lying about their specs. People really need to know this information. Knowledge is the key to holding companies accountable for scamming its customers.

The Modes Listed In This Video Are Incorrect!!! I was just sent on a 6-hour wild goose chase trying to track down why my microcontroller wasn't transmitting in the correct mode based on the timings I measured on my logic analyzer, only to find out the modes listed in this video are incorrect, so it was working correctly the whole time! The video has the CLK Phase incorrect; therefore, Modes 1 and 2 and Modes 3 and 4 are switched!

I love your explanation with diagrams and waveforms. Would you please explain the topology Phase Shifted Full Bridge... thanks a lot for your great work ❤❤

Great information. Thank you!

Nice explanation 😊❤ I saw my low pass filter and pre amp board using Ne5532 op amp ic... ... Can you do some practical projects also

Can we charger the li-ion Battery with Regulated power supply by keeping the Voltage and current parameters as per system standard c rate and voltage ..Is it safe method?? Kindly clarify Brother...

Bro I'm learning electronics... Your videos are so helpful 🙏🏻 Keep uploading more and more videos on electronic circuitry 🤗

Please make a practical video. Design physically and test efficiency

Very good explanation, Thank you very much

Can that technique be used when connecting power supplies in parallel? To avoid reverse voltage to the smallest power supply?

hope you talk about inverter and protect circuit overvoltage,overcurrent soon.Thanks

Nice bro

how other nodes ignore the message during broadcast, please tell technically

How does changing the duty cyle affects the output?

Why not chose a film cap?

'promo sm' 👉

Sir, your explanations are very useful for my project & animation is very impressive. from which software do you make animation.

amazing explanatio ., what you refered for all this deep knowledge?? Pls share

CAN DOS CAN DO CAN BUS

How can you avoid the HIGH current flowing in Q1/Q2 when transitioning?

Good work!

how to interfae uart with microcontroller and also tell the hardware connection 0f uart

Clear explanation, straight to the point and correct. Thank you very much for the video, I'm sure it helped a lot of people!

Have a good day. I really like your contents and learned some things, thanks. Have a question: Why actual signal applied to Q1 Transistor with "2 NOT Gates" ? I thought, creating a dead time between Q1 signal and Q2 signal. Is it true or this question has another answer? If you answer, I will appriciate, thanks again.