fishtapes are a mild/spring steel, meaning there's a lot of tension in the line. Softening the grain of the metal prior to forming makes it not only bend easier, but it also makes it stronger since you're actually deforming and normalizing the grain, meaning less separation between the layers of the grain. If you want to cool it down faster and also lubricate the head, you can melt the tip of a wax pencil on it, might make it harder to tape though.

I have Eaten a bird before they are not robots

I think you ought to try art class again !

This guy talks to much just show how it’s done mayne

That's what's up

Sucks

No box offsets 🤔🤔

"Pasteurize. They pasteurize milk." - Louis Pasteur

i’m not a tradesman, im in sales and sometimes i sell equipment that needs some plumbing, usually pvc but sometimes SS tubing. I never learned how to measure and bend correctly, this has solved that problem! thank you so much!

Thanks for the knowledge transfer

Roll your sleeves back up, dummy!

I have an outlet that is receiving power, but nothing works when I plug it in. I replaced it without success and the next outlet downstream has the same issue, I have not changed out that one yet. I did also check the connections to the pigtails, they all appear in good condition. The outlet which I believe is before this one is fine. Any advice?

Nah when I ask an employee to do something and they do something different I’m getting pissed

When you get mad at other people, you're just transferring your own responsibility onto someone else so that you don't take responsibility for your failures. It's always your responsibility

As a 5th year, I appreciate the mistake making the video

Dude this video is 6 minutes too long

8 years in the trade. Majority has been running rigid, I was always taught to avoid saddles like the plague. I’m on a massive commercial sight and they beat the saddle drum and they are all over the place. They act like it’s a prize skill

Contact me and let me tell you about KNX and what endless possibilities you can have with your lighting.

😅 I did when working nights

I'm remodeling a bathroom where the existing outlet was very close to the sink (a mid-century home built in 1951). The new sink is a bit larger and has 8-inch faucet spacing which reduces the distance between outlet and faucet so I'm moving the outlet a foot to the left. However, the existing outlet box was attached to a stud. Once I drilled a hole, Romex solid wire is almost impossible to work with over the short distance so I've ordered stranded wire to use to splice the existing wires to the new outlet. I hated having to buy additional wire but it sounds like stranded wire's flexibility should resolve some of the installation problems I've experienced. (BTW, I'm not completely opening the walls which made it harder to use Romex solid wire).

Ok that into though... 🔥

Like how you're pouches are used Show you work and real life mistakes lol

Will the equation be the same for each size conduit ; 11/2 ;1;3/4; 1/2

He taught me how to bend my fish tape! Great job boss.. 😂 #WhataWaste..lol

Polecam poszukać w necie, a nie pitolić że nie ma znaczenia ile odizolujesz drut. To ma dojść do końca, jak nie dojdzie to znaczy że trzeba poprawić. Te złączki bez dziwgienki są szczególnie wrażliwe na za krótkie druty. Lubią same się wypiąć, więc to dowód że styl jest slaby

Don’t you think adding electrical tape around the wire & the WAGO connection would add strain relief? Strain relief is used in almost all related fields like Aviation Electronics. It keeps the wires where they’re supposed to be even if there is a bad connection at the connector. Too bad you can’t get Cannon Plugs at Home Depot. It would make wiring a house a piece of cake.

the reason his bend was underbent... He wanted to hit the center of the box? then measure from the center of the first one. He measured from the outside right of the pipe, but the bender is working with the LEFT side of the pipe when its said and done, due to his use of the right side of the pipe. so you always want to measure from the center of the knock out to the center of the knock out that youre going for.

Excellent job. Excellent video presentation

They also continue to use electricity even when you're not charging your phone. It is a small amount but it does add up

doing a lot of steel conduit work at this building site im on currently, never done anything to do with conduit prior this job so im learning what i can.. them benders you are using. does it work with steel conduit or is it aluminium only?

"So if you unplug it it will go back down to zero?"No it will magically go up to 1,000 volts..smh.. For the love of God plz stop.

couldnt you just poke a regular probe into the usb port why do u need a special device for that

What I don't like about these devices is, its like a wall wart thats always on consuming power inside your wall.

Dude do you not have google? Just buy one exactly as you described they make em!

Klein also makes the best Bongs

Nice tool, but all of these outlets are junk. They can't keep up with newer phones

Klien has the most niche, but extremely helpful tools ever made, I love them so much

how about 2 receptacles what mudring?

It was all a rickroll guys, really you CAN use an extension cord. (Some idiot is gonna burn down their gouse after they read this comment)

@5:30 ...that sigh made me lose my sheit 😂😅 i know that feeling AF... TIME TO FIX THAT DOGGY ...

Your buddy Wade looks like Trent Dilfer.

💯🔥

Also, this is all BS. Quality depends mostly on volume of work. If you don't have a lot of work, you'll need to switch to quality service to compete. Too much volume and the standards drop to match.

Ya... don't worry, the excited new guys will have their excitement squashed, like always.

Eaton.... DEEZ NUTS

You can possibly get around flickering LED's by buying better bulbs, especially the USA made dimmable ones.

He sounded like Theo Von in the beginning. 😂

Why would there be 4 ground wires coming into the box in the first place?

Count shrinkage

Nice 😆