hello. it seems you have a negative angle. this is not achievable normally. did you edit your cad settings ?

Hi Mr Wally ! First of all thank you for your support to the digital dentistry ! It's really valuable the experiences that you are sharing. Im having a big problem with the primescan bite scan Intersections (even with the check mark).I started even scanning after getting my 3d printed models to the articulator but I still can't get precise bite registerations without intersections. Here ( In the video sec.31)I can also see that you have some interactions, which causes me occlusal height in my restorations. Do you have any solution for that ?(beside bitefinder etc.) or did you heard about someone getting solution to that ?

Great Work! I think SprintRay Intervened in this Case

Which resin did u use and which 3d printer...?

Uh, whoa! 👏🏼👏🏼

🔥👍🏻👍🏻👍🏻

So I purchased the aoral elite scanner because I wanted the iPG capabilities but I'm not really impressed with the tissue scan capabilities. Would this be a good solution and alternative to PG? This would allow me to get a trios 5 and not have to get a true PG which are crazy expensive.

Nice. Did you polish in between?

Hi doctor, where did you buy the dental models you show in the video?

Too complex and involved!

nice tutorial , so I only can use it to only direct screw and bar , I can,t use the OEM prosthetic solutions

Hi Wally, where I can find info about 79% of ceramic? It’s 79% in condesable IPS Empress Direct, not flowable IPS Empress Direct Effect. The last one filled by ceramic on 49-67%

Do you still need Truabutment io connect if you have this intraoral PG? I was debating between this vs Trios + IO Connect but after seeing this review, I'm leaning towards shining.

Are 3d printed veneers stronger than e-max?

Thanks for this great review... Best wishes from Austria, Europe....

If bonding to enamel as in a Maryland Bridge, how do you treat the enamel? If cementing to dentin as in an inlay, how do you treat the dentin?

Thanks wally! Super helpful

What material are you printing these in? Do you get flex with the clasps?

Wally, thanks for the review. I'm looking to get a new facial scanner. I bought an Instrarisa and felt like I went the wrong direction.

Do you still have the STL for the retractors?

u gotta copyright your palatal marker " the udder"...breadcrumbs are now dead...long live The Udder!

This video really helped me a lot!! thanks

The tooth is the onx material but what material do you use for the base. Can i use the clear nightguard material for the base?

Hey doc! 1) great work! 2) what code are you charging for these patients? Is it still considered a composite restoration or same code as indirect onlay? 3) From start to finish (prep, design, mill, insertion, radiograph) how long on average would you say you are scheduling out for a restoration? Obviously I know this varies patient to patient

was doing pretty much the same thing last week for the first time. worked perfectly. Small difference: here in germany we‘re not allowed to make such small dentures as the risk of aspiration is pretty high. we need to have clamps accross the palatinum (Q1 to Q2 f.e.)

🔥👍🏻

I watched my dentist break off a little tab in the front and then I tried it on for fitting. It tastes like chemicals and is not smooth all over. Did he miss a vital step in curing or sealing the mouthguard?

Awesome video. To bond the tooth to the base, what do you use?

Thanks for the info, great video! If you print as one merged file, rather than split-file, what are the settings for ‘adapt tooth pocket’ in exocad?

Hello wally how did you designed this ultra thin 0.2 mm thickness veneers

What is shade of cement did you use ?

I am super pump with the possibility of today's technology.. Thank you for sharing your workflow🎉.. really inspiring

I love the content

So the glicerine seals the tint? Or we put a barnish

splendid discussion of all the face scanner softwares. Cheers!

Thank you for this fantastic review ! ❤

Iam looking everywhere for this clone software, and still cannot found it, where is it? Is there any special site to download it?

This is the content i watch at 3am😂

Can you make dental veneers or onlays with this software?

One very clear texture and also mesh that goes to 100 microns on teeth is the POP3 from Revopoint. Started using for a short time but am blown away by the quality.

Have you tried the Einscan Pro 2X V2. It’s in the 10k range and not specifically for dental but looks very good. If I could get a try before you buy I think it could be awesome. Not an endorsement I haven’t tried it, I have just researched it

Incredible!

What file do you work with for this?

could you have pre-printed shell temps for this case and relined with bis-acryl or will this option be as good if not better?

Can i take the course if i dont know nothing on exocad?

Hi!When we will se a review with the 3Dprinter Formlab 4B? Regards!

Thank you for sharing, do you have an article for that?

Maybe the best most complex looking at all different kind of aspects review ive ever seen . Big THX for that . If i were Kevin Ping i would ask you to become Beta test boy. But thats just a wish .

Best scanner review I’ve ever seen. 🔝. Can you make a video explaining how you use that piece on the palate to match meshes? How it’s done and how you fixate it? Thanks

what tint colors of ivoclar you used?