It would be nice if they make updated video this was recorded 12 years ago

You saved my life (and perhaps that of me cell) by pointing out the cell unthreads counter clockwise. Thank you so much!

Do you know where the reset button is on the infinity 2000 series motor is located? Thanks.

How much does a pool like this cost?

Excellent - would've been good to see what the finished, cleaned blades look like, too.

Will this work with a non steel wall pool ?

Buy now at www.royalswimmingpools.com/10-lbs-royal-pool-blend.html

Would 3.7 resistance be too much for the transformer

Can this be used for a flooded basement?

I would like to get a price on the pool kit for a 16' by 32' in ground

How do we get the ro-es loose so we can do this. That’s the most important part.

what is the cost of install on a pool this size w the automatic cover?

Dang, that was almost a helpful video!!

Great video. Great stuff.

You should also mention that there should be at least some water in the pool before doing this, preferably half way or so. otherwise if u do this before adding any water the opening will stretch when water is pumped into the pool. liked and subbed regardless!!

@Royal Swimming Pools - Please redo this video showing the proper installation of the skimmer. Butterfly gasket covers BOTH the liner and pool wall. Leaking will occur if installed as shown in this video.

These light bulbs are up to a $1,000 to replace and ours worked less than a year. they fill up with water after awhile and stop working. The company hasn't bothered to fix these faulty expensive lights and continue to sell these crappy lights to unsuspecting buyers!

TOTAL CRAP!!! DON'T BUY!

Music is terrible, but great video tho!

I am a 44 year old woman on disability and I just put a skimmer , an upgraded jet , and a new pump on my pool by myself . And I siliconed around the new additions. If I can do it anyone can

In Chemistry we learned, "Add the acid to the water and you're doing what you oughter." Goofy, but 45 years later, I still remember.

Make sure to relieve the pressure in the system before you remove the cell.

So no gasket between the inside skimmer plate and liner?

Which cantilever forms were used to be able to install liner before the concrete?

1 part acid 4 parts water? I don’t understand. Please explain with visual content.

So much info, so concise. Take these readings with power on? Filter on?

Good video!

2gxgwiwhiners d'oeuvre ovaries m quantization fth dhd if str j h elven

is that inch? or ft or in Metre

THANK YOU!

My instructions show that the inside of the butterfly gasket should contain both the wall and liner, rather than have the gasket over the liner. But I'm nervous to cut the liner first.

Hey how much for 20x40 inground concete pool in NC with just the pool and fence could you give me a eastmite sence you work with stuff like this I got a 100,000$ budget.

What exactly would that cost turn key job sort of speak?

In ground pool? always use rebar and shotcrete. 1 time job. not a new liner every 8 years.

How do you contact the team to do it for you ?

A video on your grounding and bonding would be good. Since your instructions don’t show much.

What vacuum hooks up to that?

I can't find any motor to replace it with. Any suggestions on where to buy it?

Thinking about getting a large pool or 2022 gmc at4 Since I live in Texas and it’s hot 🥵

We have the EXACT skimmer model he shows installation for and we just looked at the manual. It CLEARLY states that the rubber gasket goes over the steel wall but OVER the liner. 1. CUT LINER FIRST. 2. THEN, INSTALL GASKET OVER BOTH. Don't make our mistake-water leaked out from the inside DOWN past the liner and onto the inside of the pool wall. NOT GOOD and the very reason you're supposed to do the above. Not sure where this guy gets his training but it is OPPOSITE the actual manual for this exact skimmer. Please learn from our nightmare.

Guatemala

I have to replace my skimmer, question on beside the gasket. Should I use RTV or silicone. Thanks.

Great ! However, where are the grade beams at the bottom of the pool ?

THIS VIDEO IS WRONG. THE PLUG SHOULD BE ON THE OTHER SIDE, THE TOP, NOT THE BOTTOM, WHEN YOU SCREW THE STAND ON. EVERY OTHER VIDEO THAT I LOOKED AT SHOWS THAT THE PLUG SHOULD BE ON THE TOP AND THE STAND SCREWED IN ON THE OTHER SIDE, ON THE BOTTOM.

You do understand that the purpose of a video is so that the viewer does not need to read.

Great video! Just installed my aerobic septic….which was easy af. Now gonna dig my pits, who love water, their own natural pool. Don’t mind the holier than thou losers who are dreamers….not doers. These commenters wouldn’t know how to put actions to their ideas if they were motivated by Tony Robbins

Ooooo

My timer shuts the pump off e every 15 minutes can't get it to stop.

How about making a white pool deck expansion joint that doesn't crack to pieces after a few years that could withstand a woman's shoe heel? If you wanted to design a plastic joint thats sure to crack and look like shit you could not do it any better than the razor thin tops of that material.

Junk