Hi. Is there any way that I could contact you directly please?

Can anyone tell me the type and size screwdriver to open the battery ? It is Torx ? I proof that ones but can't 😢

My 4ah einhell power xchange battery had a different fault. All three LEDs would flash nine times. The cells were all full and yet it wouldn't drive any tools. Seen little use and was well out of warranty. Swapped out the battery circuit board with an einhell 4ah replacement board from AliExpress for £6.

Hi, this model donst have Green leds level in the battery when Is full?

After one year still works great..

It seems like a lot of kerfuffle when the batteries and chargers are so cheap I was gonna try and fix my one but I’ve got a good deal on a charger and a battery so it will be going to not landfill my local dump for responsible recycling. Or I might put in the local supermarkets battery bin

Show you replace the bad cells??i didnt see the solution??

I have a battery that shows the green and red LED on but not blinking. Stored it in room temperature but it has no effect. Is there an other way to charge the batteries separately ? Such a T240 is more expensive than a new battery.

I didn't fully understand how to individuate the faulty cell. I get i have to measure the voltage and look for batteries below the minimum threshold but where can i find out this value?

💦💧👍

La música un poco incomoda, El diorama bien trabajado.

All the best!! I am working with same too!!

bravo

You do not have to disconnect the battery to charge it. All cells can be charged individually while connected. Those cells went out of balance. This happens usually because the battery is not charged to 100%. The BMS on that battery is a top balancer, meaning it will only start balancing when it is over 4.1 volts, around 90%. If you don't charge it all the way, it never balances, and some cells will have lower voltage than others. It is a bit counterintuitive, in that, it is harmful to charge your batteries to 100% but at the same time because of the circuitry on your battery, you kind of have to.

Make it in resin would be good idea

Possibly a little bit "too wrecked". Any one of those damages would have sunk it. Dont need a half dozen :O . Other than that, excellent work.

Well done for using a decent size model, not the pissy little ones that most KZbinrs seem to use.

Nice Video thanks, greetings from Germany

have a nice day. There is NTC heat resistance under the yellow band on the battery. Can you measure and tell me how many ohms it is?

Just a few safety tips: Don't wear rings when handling the cells - can cause shorts Don't use metal tools - can cause shorts Don't solder tabs on lithium cells - cell can catch fire

bien. ahora solo necesito un torno para reparar mi rx580

Can I Just replace the bad cell with another one, diferent brand but same voltage and amperage?

Can you name of the charger that you use?

Nice job, keep up the good work

Nicely done! Thanks to you now all i need is to buy a lathe and place it in my room😎. Because i got the exact same model than your.

hi! very good job with rust, and I also like washes. I have a similar diorama planned for my channel shortly and your video has inspired me with new ideas. thanks for sharing!

So good sir, did it hold?

Thanks, I had exactly the same issue with a 3Ah pack - one cell pair was down to ~0.2V :o - bumped the bad cells' voltage up to around 3.5V @100mA using a bench supply before upping it to 1A to get it up to 4.1V to balance with the other cells and the charger seemed to then be happy with the pack - think the reason was not being used all winter but puzzled as to why one cell pair went bad :/ P.S. The music is a little distracting!

2:14 ,,beater"... + this music (are you listening this ??? :o 0/10 ) best regards /thumbs up , I wish you miliard viewers like me BANG!

Παρά πολύ χιόνι απίθανο ποσό θαθελα να ήμουν και εγω