CORE 4X4

Пікірлер

@veerod383 3 күн бұрын

Nice equipment, but honestly, you need proper training. Alignment starts with adjusting the thrust angle first, ensuring the rear axle is squared to the vehicle’s centerline. Skipping this step or doing it out of order lengthens the process because you’ll have to backtrack to fix changes that occur to angles affected downstream-like how an incorrect thrust angle will alter your steer-ahead alignment later. Once the thrust angle is set, you move to the front, setting camber and caster before touching toe. Toe adjustments must be made with the steering at zero steer ahead, aligned to the thrust line. Only after this step do you center the steering wheel, and that’s achieved by fine-tuning the drag link. Skipping or misordering these steps compromises the alignment and wastes time correcting earlier mistakes.

@texasbradley 6 күн бұрын

Those are rear upper and lower TRAILING arms... Control arms mount east to west, trailing arms are north to south.

@DanteSexton-m4r 9 күн бұрын

Rusty jeeps are the best jeeps.

@CheechDogg.0n37s 9 күн бұрын

Finally ordered mine along with the rear uppers and panhard .... Hope I ordered the correct length though ... I spoke to Valerie on the phone and she told me to email support ....

@davidbrigham6186 5 күн бұрын

What? So did we order the correct ones?

@westcoast3595 13 күн бұрын

I am happy with my core control arms

@jayskateandsuchstuff8446 15 күн бұрын

Great kit! Would love this for my 07. One question, it uses transmission crossmember mounts so can you get your transmission out without disassembling your suspension?

@BentRebar 16 күн бұрын

I just received my order of upper control arms from Core 4×4. I encourage all to check them out. They offer three levels of stoutness vs. Streetibilty, and they have a whole pallet of colors that you can choose from. And I should not forget that their prices are incredibly reasonable.

@brayanvazquez7857 18 күн бұрын

What size wrench should I get for the nut next to the Johnny joint

@bryanoverton4675 20 күн бұрын

What size tires are you running on that XJ?

@pedrog4221 23 күн бұрын

Good morning. Can this modification be done with the stock steering???

@mikehydroseed1282 25 күн бұрын

Does the lifetime warranty cover the bushings?

@core4x4fab 22 күн бұрын

Unfortunately, they're not. Our lifetime warranty only covers non-wearable parts. If you'd like to look into our warranty in further detail you can find it posted on our website at core4x4.com/warranty/

@Yo_Dadas_Kitchen 28 күн бұрын

Need a good alignment shop in my area

@nickcarter714 28 күн бұрын

After coming back and fourth to this video about 50 times during install, I just finished it up 😅

@neiljohnermac Ай бұрын

Aren't you supposed to torque down at ride height level? Also, does the bushing end connect to the frame or axle end?

@q5quint Ай бұрын

I put this on a 300k mile xj with mega sloppy steering and it surprisingly 'cured' about 50% of the slop. It was a night and day difference. New ball joints and tie rod ends are next up.

@10dannyp89 Ай бұрын

Driveshaft spacer to make up for the distance the axle is moved forwards?

@KyleErickson-bu1mj Ай бұрын

Lachy plz like my comment I’m subscribed

@KyleErickson-bu1mj Ай бұрын

Lachy plz like my comment I’m subsribed

@markstutte5997 Ай бұрын

How rough is it to daily drive on a crawl series lift for an xj? Really love the content and I plan to eventually buy a lift kit later on, I’m just a lil stuck between the camp and crawl series lift.

@bryanoverton4675 Ай бұрын

Great Job! Enjoyed it.

@bryanoverton4675 Ай бұрын

Ordered the long arm kit. Cant wait.

@core4x4fab Ай бұрын

@@bryanoverton4675 thank you so much for the support!

@DCmite1 Ай бұрын

for 3.5 lift do you recommend short arm or long arm?

@heribertovega3240 Ай бұрын

What is the measurements for a 6 inches lift?

@aarondwyer3746 Ай бұрын

I ll have to try them out next

@aarondwyer3746 Ай бұрын

It's a very nice piece of kit there,

@core4x4fab Ай бұрын

Thank you! We definitely love it.

@divinelyranconsciousness Ай бұрын

I noticed the jeep wk doesnt have front control arms and just the rear. Does not have the same issue since its not a same front end design? What do you all recommend as far as the front if you do the back with the crawler set up on 2005 wk. Currently running old man emu springs bilstein 5100 and jba uca 255 75 17. Thanks

@robbywhited910 Ай бұрын

Need this for my 2019 ram 1500 has a 5” Fabtech radius arm lift kit. Needs a new track bar it moves slightly and clunks.

@advanceddoorsandsecurity1245 Ай бұрын

Great break down no fluff Thanks!

@antoniodavis9848 Ай бұрын

Great video and looks good install, i will be doing a gear change in my 2017 Ram 1500 Bighorn crew cab, 3.21 to 3.55 with tru trac and would like to know whould my rearend benifit from your control arms.....

@CheechDogg.0n37s 5 күн бұрын

Absolutely! I have a 2018 Ram 1500 and adding the rear control arms helped it a lot especially on washboard roads .... I'm about to add the panhard and rear upper control arms and the front upper control arms as well. I will have the complete set that core 4x4 offers for our trucks, get them, you won't be disappointed!

@HEMICONNECTIONS 2 ай бұрын

Do you know if it fits a 2014 Jeep Patriot? Thanks!

@ST8-PRK-RNGR 2 ай бұрын

Great content would love to see more on how it performs and information on tire clearances.

@michaelcraig6857 2 ай бұрын

Will these link brackets work with frame stiffeners? More worried about the rear since it sandwiches the frame rail

@Precisionmobile 2 ай бұрын

Do you set the Adjustable track bar Length at full droop or half droop or when the trucks on the ground?

@gizzmo2875 2 ай бұрын

Do you have a 4-link conversion for the 4.5-5 gen Rams in development? I want near zero lift WITH 4-links and a design similar to this would allow that (ie reuse stock radius arm location).

@core4x4fab 2 ай бұрын

@gizzmo2875 nothing in the works currently. We do have our new radius arms for these trucks, though.

@Filatov_999 2 ай бұрын

Скольки стоит комплект ваших рычагов?

@platonpanagopoulos73 2 ай бұрын

Hello - great video! I purchased the full kit (cruise) what about the rear pinion angle? what are the optimal settings ? thanks!

@hotbusa08 2 ай бұрын

That might be the best made vehicle you will ever work on built to last hundred of thousands of miles unlike the jeeps thousands then get a new one

@j.c.smithprojects 2 ай бұрын

im building a truck with a 12k front axle. is there a johnny joint that is heavy enough for this? going to be a parallel 4 link air ride straight steer axle