Hi sir. I have a question. The library or driver files that you use (e22900t22d.h and e22900t22d.c). We can use the LoRa modules without these files right? Since the stm32 board run with LoRa as default, as you said before.
@patrickruiz49454 күн бұрын
Hello I have an ESP32 S3 Atom Lite and since the ESPHOME 8.0 version it has been introduced the LVGL and I have lost screen display Have you seen this problem? THANKS
@patrickruiz49454 күн бұрын
Hello I have an ESP32 S3 Atom Lite and since the ESPHOME 8.0 version it has been introduced the LVGL and I have lost screen display Have you seen this problem? THANKS
@mirovskii8 күн бұрын
Hi sir, thank you for the video and explanations. I want to ask that, can't we use the LoRa modules without using FreeRTOS? Do stm32 boards not include the needed softwares for that?
@usefulelectronics8 күн бұрын
Adding FreeRTOS is an optional feature. STM32 runs without RTOS by default. So yea you can use LoRa module without using RTOS
@mirovskii7 күн бұрын
@@usefulelectronics Thank you for your response. I made the project to communicate 2 stm32 blue pill boards. When I arrange the wiring just for the UART communication between boards, it works. But after I change the wiring according to the LoRa e22-900t22s modules, it does not work. I am sure about the wiring, parameters like baud rate, channel etc. What could be the issue?
@iamkian14 күн бұрын
I have had a look at your GitHub, but can not find the needed code for the "ESP32S3 HLK-LD1125H Human Presence Sensor" project :-(
@222inverter18 күн бұрын
Great tutorial thanks for giving your time to explain this..👍
@MakerSpaceOnline23 күн бұрын
Would at least be nice to mention the original creator.
@jacekf23 күн бұрын
does it have to be S3? how about just ESP32? ESP8266?
@usefulelectronics23 күн бұрын
@@jacekf ESP32 is ok. ESP8288 doesn’t have parallel interface support
@rdyer876424 күн бұрын
👍
@nicolasfiore26 күн бұрын
Y el resultado final casi no se ve 🤷🏻
@DmitryDC26 күн бұрын
fake link
@TheBinklemNetwork25 күн бұрын
Wrong link, not fake
@lorenbentley576625 күн бұрын
@@TheBinklemNetwork Do you have the right link?
@zeynepkoca828329 күн бұрын
Useful and awesome video :))
@usefulelectronics29 күн бұрын
@@zeynepkoca8283 thank you for the support Zeynep I wish you a nice and useful internship :)
@zeynepkoca828329 күн бұрын
@@usefulelectronics You are welcome, Hocam:) thank you for your nice wishes 😊
@phoenixdonner855329 күн бұрын
Very cool!
@shamssalehin2376Ай бұрын
Solder mask Color? Matte Black Or Matte Green?
@usefulelectronicsАй бұрын
@@shamssalehin2376 matte black
@mbundsАй бұрын
Projects like this one give me huge respect for smart watch manufacturers, who get all of this functionality, along with their batteries packed inside a watch case, that can run for days. Thanks, Useful Electronics, for an excellent production!
@joecheagarayАй бұрын
Hello, I'm using Expressif IDF 5.3 and got a build error, which version did you use? :)
@joecheagarayАй бұрын
#include "rom/gpio.h" was missing in the main
@usefulelectronicsАй бұрын
@@joecheagaray I had compiled the code with ESP-IDF v4.4.3.
@AlkatrossАй бұрын
1 km should be no problem. I wonder how it does at 10 km. Theoretical maximum.
@butterd0g_Ай бұрын
no more messy work desk. great!!!
@ZuubiikАй бұрын
how to run this with a THMI 2.8" with parallel interface?
@usefulelectronicsАй бұрын
Hi, You will need to change the LVGL library and display driver configuration to suit the new hardware.
@ZuubiikАй бұрын
@@usefulelectronics Successful . Thanks for this video, it was very helpful
@furkanunal63382 ай бұрын
Hocam elinize sağlık. Alıcı ve verici loraların parametre ayarlarının aynı olması yeterli mi (kanal ve adres) yoksa kod içinde de adres ve kanalı alıcı loraya göndermeli miyiz?
@biscariot10742 ай бұрын
This looks like crap 😔
@MeowCatStudios2 ай бұрын
Bro they look fire 🔥
@kalashnikov_47z2 ай бұрын
1000000% Fake
@NyxKemo2 ай бұрын
Extremely shady install
@hipaperbox2 ай бұрын
wow🎉🎉🎉❤❤❤🎉🎉🎉❤❤❤
@Farquaad-Gaming2 ай бұрын
Why yhe hell are you soldering a non rechargeable battery
@josehrestrepo2 ай бұрын
Interesante el video pero no explicas técnicamente el circuito armado y programación
@BenMillen2 ай бұрын
i will literally pay someone to help me get an animated gif onto one of these, i bought 3 and cant get any of them to play nice (not this exact model but very similar)
Maalesef yok Gelen 12V buck converter ile 5V düşürüyorum ondan sonra linear regulator ile 3.3V düşüyorum. Devrenin özeti budur
@tanerriko36352 ай бұрын
Teşekkürler. eğitim videolarınızı da bekliyoruz elinize sağlık.
@tanerriko36352 ай бұрын
Başarılar ❤
@tanerriko36352 ай бұрын
Yabancı seslendirilen bşr videoda Bayrağımızı görmek gururlandırdı. Tebrikler ❤
@einlehrling2 ай бұрын
What was that for a mcb you put in there?
@shamelyazaw2 ай бұрын
worooood ❤ it's motivating to see someone so passionate about his hobbies 😁
@giannismplogas36242 ай бұрын
Adding an extra mcb to a hopefully already protected circuit? Don't see any reason... Also not a good way to install an AC unit, it should be on its own circuit with its own mcb.
@usefulelectronics2 ай бұрын
It manufacturer company asks for MCB installation to let the air conditioner warranty be valid. I also see it unnecessary
@bobby95682 ай бұрын
really cool!
@pablomeinardo7172 ай бұрын
I think the "MODE" pin should be connected to "Vss". But you say in the video that you connected it to "Vdd". Maybe you were wrong. Thanks for the video. I already bought my board to experiment.
@usefulelectronics2 ай бұрын
Hi Please Check out the sensor datasheet. If you connect the mode pin to Vss you can’t read the sensor key status register or any other register. This makes connecting the sensor to an MCU meaningless
@honeybadger23713 ай бұрын
Can i use it to charge my capacitor for my coilgun?
@usefulelectronics2 ай бұрын
I don't think so, the circuit needs feedback to keep the output voltage level at a certain level
@vigneshs62323 ай бұрын
How can I use SPI instead of I2C for the same SSD1306 Display. Please help me.
@usefulelectronics3 ай бұрын
Your display must support spi
@vigneshs62322 ай бұрын
@@usefulelectronics Yes. My SSD1306 Display supports SPI. I already programmed that display to run using SPI with other codes. But I am not able to display using LVCL library as you done in your video.
@usefulelectronics2 ай бұрын
@@vigneshs6232 I see, you will need to updated layer since it is based on I2C driver I have worked with SPI driver before to get GC9A01 Round display running github.com/UsefulElectronics/esp32s3-gc9a01-lvgl/blob/main/main/display/gc9a01.c#L34 you can have a look at it and update display_config layer accordingly
@vigneshs62322 ай бұрын
@@usefulelectronics I already gone through all your code in your Github. I also used the same project you mentioned to change the I2C to SPI. But, I am not able to get the output. I already created an issue in this Github project folder. Can you please check my code, I added in that issue? It would be really helpful for me.
@edinspiegel3 ай бұрын
Wow this is very helpful - thank you! I have one question though - if I want to decrease the amount of current that the circuit "trips" at - do I need to decrease or increase the resistance of the 1k resistor? - also will the transistor still protect against short circuits, even though it doesn't isolate the power source? Thanks in advance!
@baqtioo3 ай бұрын
Nice
@Udafff493 ай бұрын
Aaaauuuuueeeeee babe!
@anushairan283 ай бұрын
Can you share how to connect lora e5 mini with arduino to perform point to point communication
@usefulelectronics2 ай бұрын
Arduino is outdated my friend
@DRG_Boys3 ай бұрын
Which module is that?
@trendyol_azerbaycanda3 ай бұрын
Hi, do you allow me to take the video and share it?If you have your permission.
@usefulelectronics3 ай бұрын
Hi thank you for asking, No I can’t give you permission sorry
@JohnJones-oy3md3 ай бұрын
Clever!
@surbhikathane3 ай бұрын
how to read string from display using keyboard to esp32 ?
@gorkemokur4 ай бұрын
It looks amazing =)
@Zurenio4 ай бұрын
Can you give me a purchase link to buy the antenna...?
Hi! very good tutorial, just have one question, when selecting board properties in square line which board group should I use if im using the same screen and a ESP32?
@usefulelectronics4 ай бұрын
Hi, If you are using some custom hardware, the important thing is the screen dimensions and color depth.