Does limp mode change the sound and make it accelerate slower?

Not quite so easy for a woman on that last pulley. So for you girls, look on the top of the tension pulley that has the spring, and you'll see a 1/2 " socket hole put there to use a breaker bar for releasing tension on that last pulley. I'm a pretty strong woman and can't pull the belt around that last pulley by just using my hands. I bought an inexpensive 18" long breaker bar for leverage. It worked great, but wish I had gotten an even longer one, just so I wouldn't have to reach so far.. And too, the longer the bar, the better the leverage. Use a long 1/2" breaker bar and you can easily pull the spring pulley back and have plenty of slack to just lay the belt in and then release the breaker bar. Great video, though. He explained it well.

STR HD590

This just happened to my 05 prairie I had over looked that piece I never hit that piece though but my switch is stuck in off I can't manually move it to on do you have any idea what to do

Good commentary and video. I caught the Dr. Seuss shot.. " One clio, two clips, red clip, blue clip ".. 😆 (you may not have even realized you said it). Good shit..

Did you drain the brake fluid before removing the caliper?

I put some baking soda in the boiling water. The shell peals off smooth.

I ended up filing down the old plastic rivets and drilling them out with an 1/8" bit. Then used 1/8" pop-rivets to hold the spring again. Thanks for the help!

Do you happen to know the grommet size for the temp sensor?

GOOD JOB BUD

Perfect explanation!!! I'm going to give it a go.

Good work and you explained well. The JB weld kit I got does metals and plastics and was a one time use… new improved stronger version sets in 5 mins apparently have to work fast.. ur pack is great as can use again. My kit has 2 plastic sachets & mix for 1 min and apply and place fibreglass cloth over 1st layer of weld repair then put fibre cloth on and apply 2nd coat sort of thing. Similar. I think the prep is important too. Thank you. Mind u in another country and more $ for kit here…

Thanks bro

Question: do you think its safe to leave it on, because on the manual it says to turn off the splitter before turning on the car or high current and over load might happen to your devices and its making me want to return because i dont want to keep turning on and off. Thanks

Didn't show how you did it

Extremely concise and informative video. Helped me get my 02 KX carb back together. Dropping a like and a subscribe.

Worked perfect Thank you.

The manual states to check it cold and if its been running to let it sit for at least 10 mins before checking the level.

The high pitch noise surely comes from the LED driver dimming, based on PWM (Pulse width modulation) typ. at a couple of kHz.

Wooooo

I had this issue on a bike I got that sat long enough for the clutch to dry out. What I did was the oil change, but I zip tied the clutch lever down and took a flat head screw driver to gently spread the clutch disks apart (my clutch basket is directly under the fill port) that way when I poured the new oil in it all drained directly into the clutch disks.

V Good video. Thank you!. I just adjusted my headlight they were to low on one side for my 2012 accord coupe. I used long Philips head driver attached to my cordless drill. If I went clockwise direction, the beam went up.

I just installed this seat on my 24’ Grizzly / I set mine a little further back to maintain as much of the seat room as possible … it’s pretty bulky but wasn’t too bad to install Thanks for posting it was definitely helpful !

None of my speakers is playing. Only bass.. please help

And few bad thing about Fenix head light, the button go bad very quick, .. the head band can not remove while you wash, note that's I'm a mechanic and get dirty very quickly, and the worse part customer service for future or replace... I'm with Fenix hundred of dollars .. for yrs and all light.. now I move to Olight.. as least it's new and I didn't know how customer service yet, and the big thing is.. life time warranty 💪.. Olight is the best choice .. good bye Fenix.. but I love Fenix head lamp no lie.. I hope the Fix their issue..

Where can I buy this kit ?

For those who are struggling particularly with the driver side headlight adjustment, just use a #2 (size) x 6 inch (or more in length) Phillips Screwdriver. You can buy one for just ~$2.5 from walmart.

so wonderful beautiful video Kevin i love it see so nice make me so happy ❤❤❤❤❤ i love g shock so much

so wonderful beautiful video Kevin i love that so much to see so nice it make me so happy ❤❤❤❤❤

so wonderful beautiful video Kevin i love it see so nice make me so happy ❤❤❤❤❤

I just got an 03 360 prairie. It's in limp mode and will not reset and the switch is on position. The light indicator flashes a steady flash and sometimes seem to do a quick double flash. I'm at a loss as to what to look for. Do you have any ideas? I don't care to spend a few bucks on the atv because it was free just so long as it's fixed.

LMAO! Way to make a mess.

I installed mine but there no sound, turns on but no sound, can anyone help?

Mine has 215 and have drained and filled 4 times and runs like it should

If you are watching this, get an oscillating saw and save yourself a day.

The sound is a very compelling argument! It matches my tinnitus perfectly! That's an unexpected perk!

my 2011 accord has 110 but dont know if previous owner has changed the atf fluid. do you recommend just a drain and fill? or risk a flush?

Great Detailed VDO... Well Done Brother...

On a gas stove it will not continue to boil, then what?

LOL he said "shut up"

Great review!!!!!!

Kevin can you help an old lady hook up an old Magnavox player/recorder? Grateful for your expertise!

What is the size of bolt that inserts into battery ?

I just wanted to know how to reset from Km to Miles

im back for the egggss

I know its been 8yrs ago but where did you find that chrome front bumper? I have a 97 f150 and mine has a dent

Back again this year! Thanks ☺️ 😂

You keep good care of ya cars huh

8 years late, but it is bilstAin . Like the I in "I am"

Also, you might be the first person ever I’ve heard say they don’t like usb c.