Did you choose the wrong prop? Or is something wrong with the engine? No pace.
@HuuhkaRacing29 күн бұрын
I was 26P 4b Hydro. +60kn prop. I crashed the first race and Imatra was only training. Today the boat front feels so light and jumping up so I use some water on the trimtank and it drops lots of max speed.. but yeah I need to drive lots more.
@johannesnorrman12972 ай бұрын
How many knots yesterday?
@HuuhkaRacing2 ай бұрын
What u see in video around 35 - 48 knots
@johannesnorrman12972 ай бұрын
👍👍
@XSAILOR654 ай бұрын
Melkein 66, aika hyvin. Onko about kilpailupainossa?
@HuuhkaRacing4 ай бұрын
Pyöreästi vain noin 20kg alipainoinen, mutta kartturi kyydissä menee "reilusti" ylipainoiseksi.
@XSAILOR654 ай бұрын
@@HuuhkaRacing OK. No tuskinpa kamalasti pudottaa vauhtia ja painosta voi joissakin keleissä olla jopa hyötyä?
@matslindroth65894 ай бұрын
Nice speed! What prop are you using?
@HuuhkaRacing4 ай бұрын
Mercury Racing cleavers 11.25 x 22 or 11 x 22
@matslindroth65894 ай бұрын
@HuuhkaRacing Kitos! The one that came with the F4 motor I bought for my Weedo GT did not work. Looking for a Chopper II, but have had no luck. Going to reach out to MTM for advice I think.
@HuuhkaRacing4 ай бұрын
Many used cleaver is too much mod. and there isn't a cupping anyone. MTM can be good, but they are Taiwan bulk's, also Hill Marine has some good propellers. You need to just find the right one.
@matslindroth65894 ай бұрын
@HuuhkaRacing Kitos again for your replies and suggestions. I really appreciate your expert opinion. 👍 Have a fantastic boating summer!
@XSAILOR655 ай бұрын
Hyvin kulkee!
@Kyleherk5 ай бұрын
Sounds like your on the revlimiter? How you like the 115 compared to the 60? What's that setup weigh?
@HuuhkaRacing5 ай бұрын
Yeah, It needs lots of more pitch. 115hp is more fun to drive 💪 Beecraft is 80cm longer and weighs ~655kg vs. Dalla 450kg
@Kyleherk5 ай бұрын
@@HuuhkaRacing 655kg with engine and driver or bare hull ? I'm sure, it's much faster has to be more fun 😄
@HuuhkaRacing5 ай бұрын
655kg is the total: boat, engine and driver. 3A racing minimum weights are 700kg.
@danielholmbergkivi47026 ай бұрын
Clean
@KeltainenSalama10 ай бұрын
Toihan pärjää Bella Arrowille mennen tullen laukkaamisessa..miksi vene laukkaa tiedätkö.
What's with the statue thing? It's creeping me out
@XSAILOR6511 ай бұрын
Aika paljon paremmat nyt! Oliko suuttimien suodattimessa roskia, vai mikä tuon aiheutti? Lienee about samaa tekniikka kuin autoissa?
@HuuhkaRacing11 ай бұрын
Nyt mulla on uusi pulssi generaattori mistä saa säädettyä hz ja aukioloajat portaattomasti, samoin virta riittää syöttämään kaikkia suuttimia yhtä aikaa. Ihan standard ruiskusuutin eli suodatin filtterit vaihdettu ja ultrattu.
@XSAILOR6511 ай бұрын
@@HuuhkaRacing OK!
@XSAILOR65 Жыл бұрын
Meinaatko vaihtaa luokkaa ?
@HuuhkaRacing Жыл бұрын
Juu ensi kaudella ajetaan 3A:ssa.
@XSAILOR65 Жыл бұрын
@@HuuhkaRacing Onnea siihen! Pahntom 19GR olisi kova peli, ehkä paras kaikista, mutta taitavat olla melkoisissa hinnoissa...?
@HuuhkaRacing Жыл бұрын
Vaikea sanoa, mutta mielenkiintoista nähdä ensi kaudella 👍 nyt tiedossa on eri merkkisiä veneitä ainakin Smuggler RS, Tintorera parilla eri pohjalla, Bat-19, Bat-23, Beecraft, Deflector jne.
@XSAILOR65 Жыл бұрын
@@HuuhkaRacing Smugler RS on uusi tuttavuus, näyttä vähän muokatulta Aero 21 johon lisätty pari steppiä. Alimmat nousulistat tosi aivan erilaiset. Its asiassa pohja on aika samakaltainen kuin Pahntom 19GR
@HuuhkaRacing Жыл бұрын
Smuggler on muokattu Tinto.
@XSAILOR65 Жыл бұрын
Tuliko ruotsista? Mikä kone, 115hv ehkä?
@HuuhkaRacing Жыл бұрын
Jep 🇸🇪, Mercury F115 ProXS
@MrMercurymark Жыл бұрын
Aja rolamentos. Por sinal, já nem os possui!!
@franciscomunguiavelarde401311 ай бұрын
Un contenido quién sabe quién tiene herramienta para motores fuera de borda originales Yamaha detractores Sigue echándole ganas a tu canal Échale muchas ganas Nomás te pido que me pides un paro ahí para que Cuál es la herramienta de extracción original para transmitir la Yamaha del 75 del 75 hasta el 200 ocupó la estructura original alguien que sepa por ahí ahí les encargo encargo herramienta para motores fuera de borda de pago bien😂😂😂😂😂😂😂😂😂😂😂😂😂
@johnmann4214 Жыл бұрын
Top speed?
@HuuhkaRacing Жыл бұрын
Suvi goes with fishing alu prop 28-30 knots
@MrKyborgi Жыл бұрын
Hurjaa hommaa. Saisko näistä koostevideoita voice overilla?
@HuuhkaRacing Жыл бұрын
Pitää tutustua, mutta todennäköisesti joku tekstikupla onnistuisi, että mitä tapahtuu ympärillä.
@knyde Жыл бұрын
What is your max speed ? Regds Mads
@HuuhkaRacing Жыл бұрын
If I remember correctly 30-32 knots with fishing alu propeller. Getol has 1.71 gear ratio and G-gearcase.
@XSAILOR65 Жыл бұрын
What happened?
@HuuhkaRacing Жыл бұрын
Ei ollut tässä kisassa kuin pronssia tarjolla
@XSAILOR65 Жыл бұрын
@@HuuhkaRacing OK, ilmeisesti olisi pitänyt olla enemmän vauhtia? Pienestä tuo lienee kiinni, ei tarvitse olla isoa ero esim.potkurissa niin vaikutta vauhtiin.
@HuuhkaRacing Жыл бұрын
Laukkaamatta solmu pari lisää niin olisi ollut ihan eri kisa. Setuppi oli täysin sama kuin Norjassa MM kilpailussa.
@XSAILOR65 Жыл бұрын
@@HuuhkaRacing Outo juttu. Norjassa on melko suolainen vesi, siis jonkin verran eroa tiheydessä sen takia, mutta eipä uskoisi vaikuttavan laukkaamiseen.
@jannevesterlund8023 Жыл бұрын
Hurjaa menoa💪
@XSAILOR65 Жыл бұрын
hyvinhän tuo kulki!
@kuriwaromi1630 Жыл бұрын
Hy.. bos bisa kah saya memesan plopeller d bos kc.. kalau bisa saya minta no contack wa....
@QsVxAqua Жыл бұрын
16ft?
@HuuhkaRacing Жыл бұрын
~5m
@AndyBraithwaite-ol6xl Жыл бұрын
I need prop like that for my 40 hp
@amgluk Жыл бұрын
Nice to see that somebody is using a level for the pitch measurements. Don't forget to apply a correction factor considering the difference between the measured angle and the angle of the development plane. kzbin.info/www/bejne/onybmJqCf9mXfMU
@nasrulnsr3051 Жыл бұрын
Yg Daun 4 untuk mesin berapa pk bosqu
@jan-eriklundberg3259 Жыл бұрын
Grepen can be very bad...
@HuuhkaRacing Жыл бұрын
Yep 👍
@Audis667 Жыл бұрын
You have wrong measure. Need measure without interceptor.
@HuuhkaRacing Жыл бұрын
I have measure this propeller also pitch gauge and pitch is ~20P. Ron Hill has stamp wrong pitch.
@lisandrohernandezcamarero2560 Жыл бұрын
Hello, please,friend, help me With propella for 15 hp.
@HuuhkaRacing Жыл бұрын
What engine you have?
@lisandrohernandezcamarero2560 Жыл бұрын
@@HuuhkaRacing 15 yamaha two-stroke engine friend
@HuuhkaRacing Жыл бұрын
@@lisandrohernandezcamarero2560 ebay example: Ron Hill Signature Propellers Signature Semi Cleaver Propeller for Yamaha 20-30 HP PH16R3R
@lisandrohernandezcamarero2560 Жыл бұрын
Sorry , I almost didn't understand KZbin, I speack more Spanish , my friend.
@lisandrohernandezcamarero2560 Жыл бұрын
What I need to know how to get a propel that gives me much more in my 15 for example a cleever but know which one is the right one and where to order it from Mexico. If you want, I can give you my number and send you the videos of how the boat races are here.
@jannevesterlund80232 жыл бұрын
Kovaa menoa💪
@ivanmirchev31152 жыл бұрын
Sir, you revved the living shit out of it.
@HuuhkaRacing2 жыл бұрын
7000rpm WOT is target on the water
@vollev40r2 жыл бұрын
Olisi mukava saada kypärään kamera näyttämään eteenpäin 👍
@HuuhkaRacing2 жыл бұрын
Kypäräkamerat on kielletty, mutta voin katsella olisiko muuta sopivaa "kuskin" kuvakulmaa.
@vollev40r2 жыл бұрын
@@HuuhkaRacing ois kiva juu. Näkisi tilanteen paremmin.
@24Tunnel2 жыл бұрын
Any power upgrades
@HuuhkaRacing2 жыл бұрын
Stock engine
@emslo28102 жыл бұрын
What engine and propeller do you use? What speed did u get without waterpickup? I have a dalla pieta and im going to use a 50 tohatsu, i have a 12x17 balistic propell, but i suspect it is a bit small. I have a manual lift and wondering if i should install waterpickup.
@HuuhkaRacing2 жыл бұрын
Yamaha 50hp 3-cyl 849cc getol. I think prop was 10.6x19 CES or 11x18 Ron Hill. Maybe u should think cleaver or chopper propeller.. After that I made epoxy nosecone, because water pressure was little bit too low for Yamaha. 2015 -> I have use Mercury F60 efi formula race with out water pickup or nosecone. Prop axel is -30mm under bottom and water is Okey.
@emslo28102 жыл бұрын
@@HuuhkaRacing Nice, what speed did you get with the yamaha 50? And what propeller do you use now? Chopper or cleaver? (On the merc 60) thank you for fast response.
@HuuhkaRacing2 жыл бұрын
@@emslo2810 51 knots with Yamaha 50hp. F60 Formula Race goes 55 knots with 22" Mercury cleaver. Speed test 2021: kzbin.info/www/bejne/hqjNkKZrlLSrjsk
@emslo28102 жыл бұрын
@@HuuhkaRacing 51 knots? Wow, have you tuned it at all? And you ran a cleaver without waterpickup?
@HuuhkaRacing2 жыл бұрын
@@emslo2810 100% stock. Yep cleaver and prop axel was around -30-35mm under bottom, but I say Yamaha need's water pickup or nosecone. Here is 51kn run, but it ends overheating alarm: kzbin.info/www/bejne/oH-YY3-IpcSHp9U
@mohdfadzier83382 жыл бұрын
What hp this propeller?
@HuuhkaRacing2 жыл бұрын
Mercury F60 EFI Formula Race and 22" Mercury cleaver
@XSAILOR652 жыл бұрын
Melko samaa vauhtia kuin dallapieta?
@HuuhkaRacing2 жыл бұрын
Juu. Dalla kulkee sen 55 solmua noin 450kg painolla ja tämä on suunnilleen 100kg kevyempi. Toiveissa olisi, että keväällä kulkee pienen pohjan korjauksen ja muutoksen jälkeen kovemmin. Moottorina tässä on vakio 2t Yamaha 70hv, g-vaihteistolla.
@XSAILOR652 жыл бұрын
@@HuuhkaRacing OK. Mitä veikkaat että kulkisi Dallan koneella?
@HuuhkaRacing2 жыл бұрын
Tuskin ainakaan yhtään vähemmän. Tavoite olisi tällä ja F60 Formula Racella päästä 60 solmua.
@XSAILOR652 жыл бұрын
@@HuuhkaRacing OK, luulisi että se 60 menee rikki. Dallan nopeudesta, tiedä sitten nouseeko nopeus helpommin pohjan vai sitten aerodynamiikan( noste) säätämisen kautta. Swedujen dallat yllättävän nopeita.....
@HuuhkaRacing2 жыл бұрын
Toivottavasti, mutta täytyy kuitenkin käyttää säätämiseen useampi viikonloppu =) Dalla on aika hierottu paketti, mutta täytyy vielä saada testattua tämä 70hv 2t Yamaha ja Merc F60, että ollaanko samalla viivalla muutenkin kuin teoriassa. Nykyään itseasiassa mä pääsen kisapainossa Dallalla noin 50s, eräs TG ajaa tasaisesti 51s, Mäkisen muokattu Dalla kulkee about 53s ja maailmanennätys nopeus kilometrin suoralla on TG:llä 55s. Ruotsin ja Norjan Dallat kulkee about 52s
@vellfirepitas79632 жыл бұрын
Cantik kipas tu
@abdialpatir14282 жыл бұрын
Kalau untuk propeller 15hp race bisa bikin vidio nya pak
@mattiesko42422 жыл бұрын
Katso walesRR youtubesta
@Kyleherk2 жыл бұрын
What prop you got on now?
@HuuhkaRacing2 жыл бұрын
Same old 11.25 x 22 Merc Cleaver
@susannalehto79603 жыл бұрын
on ollu rankat aallot sielä. :(
@danielcaldwell91643 жыл бұрын
vaw.fyi grand
@holeelonen27833 жыл бұрын
mikä potkuri sulla, oma 450 tl samalla koneella 11 1/8 x 13 potkurilla huiput 2 päällä 28 solmua, 14 tuuman nousulla ajattelin koittaa.
@HuuhkaRacing3 жыл бұрын
13" Yamaha G-alumiini. Halkaisijaa en muista ulkoa. Bella on kaverin vene. max. nopeudessa eli vähän reilussa 30 solmussa oli kierroksia 5500-5600rpm.
@holeelonen27833 жыл бұрын
@@HuuhkaRacing Kiitos vastauksesta, siinä ihan sama potkuri siis kuin mulla nyt paikoillaan, lapojen kunnossa ja koneen asennossakin kenties pientä eroa, kun käsittääkseni 440 ja 450 ovat pieniä kosmeettisia eroja lukuunottamatta muuten ihan samoja veneitä. No koitan kumminkin tuota 14 tuuman rusettia kun keli vähän selkee ja kattelen koneen korkeuttakin vähän sillä silmällä, ihan tuore hankinta tuo paatti niin tutustuminen vielä vaiheessa. T: Timppa
@HuuhkaRacing3 жыл бұрын
AV-levy on kaverin veneessä lähes pohjan tasolla, mutta mahdollisesti 1-2cm ylitte. Trimmikulma on positiivisella, että kääntää keulan ylös.
@XSAILOR653 жыл бұрын
Hyvännäköinen kilpuri. Ilmeisesti tuosta tulossa itse vene, ei plugia?
@HuuhkaRacing3 жыл бұрын
Juu tämä on ihan ajoon rakennettu vanerivene. ns. muotinmuotin rakentamisessa pitäisi olla vielä paljon huolellisempi.
@XSAILOR653 жыл бұрын
@@HuuhkaRacing OK. Onko yhden istuttava vai tuleeko V60 luokkaan?
@HuuhkaRacing3 жыл бұрын
Tää on yhden istuttava ns. GT60 rataluokan proto :)
@XSAILOR653 жыл бұрын
@@HuuhkaRacing OK. Voi olla aika nopea jos samalla koneella ajelet kuin Dallapietaa :)
@HuuhkaRacing3 жыл бұрын
Jeps F60 Formula Racelle suunniteltu vene ja luokka 👍 tavoite olisi päästä suht samoihin huippuihin kuin pari muutakin venettä, sinne vähän 110 km/h paremmalle puolelle. Min. Paino 350kg
@davidheitman70043 жыл бұрын
its just a 60! i had a 2stroke pro 50 yamaha on a 13ft checkmate. shit bottom. stock, did 48 on radar. your motor is heavy! you have to use every trick in the book! ha.
@HuuhkaRacing3 жыл бұрын
62mph without navigator kzbin.info/www/bejne/j5S9maSneZyhl8k
@hjyulia6433 жыл бұрын
Hello, you email
@VivoY-cq6ye3 жыл бұрын
Ukuran berapa tu bos baling baling nya ,berapa harga tu boos
@HuuhkaRacing3 жыл бұрын
Sorry dude, I don't understand your language. Props are 3.5" gear case and 13 spline.
@jaypitasvlog35533 жыл бұрын
kzbin.info/www/bejne/eKOcc2VsmcmHis0
@BCB-Boats-Media4 жыл бұрын
Komiat maisemat! Ja hieno video muutenkin. 👌
@RamxnNoodles4 жыл бұрын
326,000 miles !!
@HuuhkaRacing4 жыл бұрын
Not Miles, km's. Today number is 450 000 kilometers
@Kyleherk4 жыл бұрын
Looks like you getting it dialed in what prop you using now? Is that boat lighter than the last white one? What's the weight?
@HuuhkaRacing4 жыл бұрын
Cruising without navigator or extra weight. If I remember right, I was 4-blade 11x21 Winrace. I think boat weight is almost sama as white one.. World Champpionship finish weight was ~535kg with crew.. And our crew weight was around 160kg.
@Kyleherk4 жыл бұрын
@@HuuhkaRacing awesome, 4 blade cleaver? Is it a regular or round top?
@HuuhkaRacing4 жыл бұрын
@@Kyleherk It's regular, I send you pic on fb messenger