I like how the commentary is detailed and oriented. I’m definitely gonna buy this kit.

Thank you so much YEARS Later!

Nice video but would rather use 2 tightened nuts on the top thread to put the stud in, those shitty pliers will chew up the stud.

Thankyou very much for this video.

Thank you this is what I wanted to know...very good information. excellent video.

Gd day,, twice a year I tune-up my samurai w/ d power of internet it’s great for u guys around, no need to disconnect& plug d vac hose of distributor,, Cody is right!.. my G13 engine maintain its 15-16kms /Lit,, thanks guys!!

Where could a find a pull scale?

Great video. Thanks

Zip lock bags do the deed just as good

Salut je suis nouveau même en français ça peut aller

Greasing the bearing tapping into the grease cage and all that ,my Grandfather showed me that back in the 1960's

Hey @lowrangeoffroad I am a producer for MTV’s Ridiculousness. May I use your video on our show? 😂

Wouldn't super glue degrade the rubber, thereby shortening it's life span? Wouldn't silicone be better?

Tienes los planos ?

Great video does this also work with 2017 toyota 4 runner ?

Great video. Covered all aspects even nut and bolt sizes for tools needed. Very thorough. 👍

What about the wrist pin install?

Great video, the only thing I would do differently is to remove the cone washers by riding the nut up to the top of the stud until it is flush, then I take a brass drift and a 3 lb sledge and smack it with the drift and sledge. The cone washers pop right off. Hitting it with a hammer can cause damage.

Can people from Australia purchase parts from your company and ship to here ???

I miss you guys being in provo.

Item is discontinued

Item is discontinued

I don't believe you lol. This would really help me buttttt 😬😬😬😬 what else is disconnected first?

1:27 The Moment Of Truth

Straight to the point. Thanks

Great tip, awful music.

He's in Suzuki that was light blue with the bars green

My dad he was in this + 9 year old

My question is, if a cv joint is mishandled and comes apart inside the boot, can it be reassembled whether the boot is left on or not? Or was that something that would damage components and need them replaced?

Is this about the same setup and removal process for a 2016?

Direct to the point.Thanks!

Looks nice. Eliminates those nasty cracks in the stock cast iron exhaust manifold.

Can I use a day old bagel to install a new bearing?

Excelente video muchas gracias

Just buy the correct tool and quit with this nonsense

Bisakah anda memberi kan saya contoh menaikan torsi fj40 bengsin tanpa merubah mesin.

Just believe seeing! I can't believe it! hahahaha

Very professional video. Many thanks! New sub...

I tried this, but it ended up toast...

Plzz county name

67 ft lbs of torque, then some more… lol

And to you that think you recognize the music: Anno 1800 Land of Lions DLC Enbesa.Your welcome

I never use loctite! only grease

Cactus in your pecker isn't a desirable experience unless you're a masochist.

Just used this technique to remove the pilot bearing from my 914 engine. Grease did not work as it shot out the sides of the bolt. Bread on the other hand worked perfect. Literally less than 2 minutes, a single piece of cheap garbage white bread. No mess, either.

Does the timing cover or pulley have an oil seal? I’m working on my 88 Suzuki and my grandpa is insisting that there was one on it.

D d!fjord

Good morning, great video even 11years later. Just purchased a 92 Geo Tracker , looking to upgrade the seats, do you have a bracket system for a 92 tracker. Thank you

TuRD

and when you’re done make a sandwich