Жыл бұрын
Жыл бұрын
Жыл бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
3 жыл бұрын
Пікірлер
@Salazar_701 Ай бұрын
That’s funny 😂😂😂 why he used the level??? The truck wasn’t level and always moving…
@WBSAddictions Ай бұрын
Madonna getting thrashed 🫡
@IvanGarcia-ft3zb 2 ай бұрын
Where u located
@R20Motorsports 2 ай бұрын
Central Florida, but we’re not really taking on work at this point. If you are looking for a shop, go to www.drycenation.com.
@Jpeaz001 2 ай бұрын
can this be used on EV engine bays
@R20Motorsports 2 ай бұрын
Yes it should be fine as there is no water involved. One would need to ensure the machine is properly grounded to the car to ensure there is no static discharge.
@MBGoodwyn1967 3 ай бұрын
Can't anyone post a video without the damn nigga music?
@joegarcia3310 3 ай бұрын
How do u adjust it if it comes too far out when closing it? Mine goes a bit over the tailgate and I have to climb on my tier to push it down so I can roll it back open
@R20Motorsports 3 ай бұрын
First I would make sure that its pushed all the way toward the cab. If it is, then it might just take some time to break in. It overlaps the top of the tailgate because there is a seal there. Also, they suggest leaving it out in the sun for the first week or so as sometimes they won’t retract without going through a few heat cycles.
@joegarcia3310 3 ай бұрын
@R20Motorsports Awesome I'll have to check that out much appreciated 😄
@donh1511 4 ай бұрын
How much did this service cost the car owner? Id love to have it done!
@R20Motorsports 4 ай бұрын
996 GT2 / GT3 run about $3K for a full underbody cleaning. Every car is different and the different generations of Porsche can vary widely.
@florinbeje 4 ай бұрын
Thank you for posting this! I changed the oil on a new to me audi rs6. The oil plug is not typical (I have 2 other Audis). Instead it looks more like the fatter transmission plug (hex head). I took the plug off and lost the washer without noticing it. After finishing the oil change I found it. I had new oil in the engine and the oil plug in without a washer. I was freaking out and I googled it and your video popped out. I couldn’t believe it possible, but had no choice. It freaking worked . Using duct tape I hooked up the vacuum hose and turned the vacuum on. Took the plug off and put the washer on it then put it back on. I did put an oil pan under because this stuff is pretty unbelievable… the whole time I was saying: No way! No freaking way!
@R20Motorsports 4 ай бұрын
Glad you liked it, thanks for watching!
@shsh5667 4 ай бұрын
What is the miata market price in this condition in the United States? In Korea, 23,000 miles eunos miata came up to $27,000. Is it a reasonable price? (If same condition)
@R20Motorsports 4 ай бұрын
About $20K or so, but in the US, Miatas were very popular so we have many to choose from.
@Rizzo528 4 ай бұрын
Keep it stock
@noahdomrose4860 7 ай бұрын
My brother picked one up today for 5k with oem hard top
@zaman-sam 8 ай бұрын
How many lb's of dry ice did u use on that Porshce for example?
@R20Motorsports 8 ай бұрын
A typical G Body 911 takes about 750 lbs of Dry ice, 1.5 blue bins
@PYRO-ON 10 ай бұрын
Why would you do this to a Porsche unless you’re the Girl Scouts
@powrfulnonsense 5 ай бұрын
What color is your porsche?
@PYRO-ON 5 ай бұрын
@@powrfulnonsense I drive a beamer black on black and a Mercedes silver on grey interior…. not hating on the Porsche, it’s a beautiful automobile but the color is just a bit strawberry short cake if u ask me…. I mean, I guess it’s OK for teenage girls classic first car but I hope a man’s not driving this.
@chappychappelle6225 10 ай бұрын
I think they meant for those control arms to be black. Lol
@brokeboi_heady710 10 ай бұрын
WTF lmao I haven’t even watched Adam’s video lol it looks amazing
@R20Motorsports 10 ай бұрын
You have some catching up to do!
@CharlesChristena 11 ай бұрын
Doing this now... When starting with the first tab... How far out should you be able to pull the grill? It feels like I get the clip, but the grill barely moves because of the other 300 clips.
@R20Motorsports 11 ай бұрын
Pull it till you hear / feel the clip release, then go one by one. Grill is pretty stiff.
@DavidNeyens Жыл бұрын
Wow! Great job. Wondering how the temperature of the vaporized dry ice might affect gaskets, seals and the joints between the various metal parts and components.
@R20Motorsports Жыл бұрын
Thanks David. This is a common question. While the dry ice is very cold and we do cool the part very rapidly, the cool / reheat process is very rapid, a matter of seconds and therefore does not impact the parts or change their characteristics. If you think about it, cars are designed to sit outside in very cold weather and therefore also have a good ability to deal with cold temperatures. Thanks for watching!
@Bmwstephen Жыл бұрын
Can these be retrofited into an m2 and m2c?
@R20Motorsports Жыл бұрын
Not sure, they look the same but you might want to check with IND for fitment.
@dandorris8531 Жыл бұрын
Interesting process, you're strippong all the protective coating that has kept the vehicle rust free all these years. Are you going to re -coat it with something or now it turns into a rust bucket. Sold on the process of the removal though.
@R20Motorsports Жыл бұрын
That decision is up to our client. In this case this vehicle will be part of a collection in a climate controlled garage and only driven occasionally so he wants it clean. We did treat some of the rusty areas on the springs and axles with a clear coating to stop any further degradation. If this were a daily use car we would obviously recommend a coating to protect it further.
@lewisthelibrarian Жыл бұрын
Hi, really beautiful car! Literally the dream spec, is it yours ?
@R20Motorsports Жыл бұрын
Thanks, it was. This video was for the Bring A Trailer listing. Sold it about a year ago. Great car.
@urischwartz6711 Жыл бұрын
You have a lot of patience!
@R20Motorsports Жыл бұрын
Yep, about 20 hours cleaning this beauty! Thanks for watching!
@hegonefishing9122 Жыл бұрын
Slow but fun....the samurai
@R20Motorsports Жыл бұрын
Total Flashback to the 80’s!
@hegonefishing9122 Жыл бұрын
@R20Motorsports would be a hit these days with the mileage they got huh.
@R20Motorsports Жыл бұрын
@@hegonefishing9122 Yeah these old light cars were pretty efficient
@wilfridBAUCHET Жыл бұрын
bonjour belle vidéo merci pour le partage cordialement
@Sandro79chief Жыл бұрын
Is that a 968 porsche?
@R20Motorsports Жыл бұрын
Its a 951, 944 Turbo S
@SnakeEyes43080 Жыл бұрын
What do I need to tell the dealership in order to get the running boards to connect to U-Connect? ‘Flash the system?’ I called and they don’t know. Also, can you deploy the boards down before you turn off the truck and they will stay deployed down for parking in a tight parking space to avoid door dings? That’s why I want them if true
@R20Motorsports Жыл бұрын
The dealer needs to update the canbus system to add the control module into UConnect. Not sure what its called, but it should be in the dealer installation instructions. If they can’t do it, you should try a different dealer or call Ram. My dealer did mine with no issue. You can use the soft switch in the center screen to manually lower these down. They will stay down when the truck is off. Not sure if they will help protect from door dings as they don’t stick out very far, but they will stay down. Good luck and thanks for watching!
@jh3755 Жыл бұрын
Beautiful… just bought a 2013 GP. Not nearly as clean as yours. I need to replace some things. Like right front fender liner, and suspension. Any idea where this baby is today?
@R20Motorsports Жыл бұрын
This is the best Mini made, great cars. I sold this car last summer to fella in Newport Beach, CA. Only had 7K miles.
@diarellhamilton23 Жыл бұрын
How love will it last ? Is it a permanent fix
@R20Motorsports Жыл бұрын
The dry ice removes the layer of oxidation where the plastic turns white. What is left is fresh new plastic so the finish should last as long as the original finish did. How fast it turns white again is a function of the environment that the car is in. Basically, moisture and sun exposure degrade the plastic to make it oxidize and dry ice doesn’t change this process, but its much more effective than a dye or protectant that just covers the problem.
@henrigutekunst2870 Жыл бұрын
promo sm ❣️
@jasonblack2553 Жыл бұрын
Just a hunch….. kzbin.info/www/bejne/noTOaqGBjsd_mMk
@jnik-hx1yp Жыл бұрын
One of these is sitting down the street in a driveway and haven't moved since a couple years, imma try to buy it of the owner. I hope they'll sell it.
@R20Motorsports Жыл бұрын
Yep, only 1,500 were made, rare car.
@rickfitzgerald4426 Жыл бұрын
Very effective process. The results say it all. Lot of work holding the wand over your head for hours though.
@R20Motorsports Жыл бұрын
Yep, gun and hose are heavy. We take our time and run half days. When you get tired you can cause damage…. Thanks for watching!
@peterworley4361 Жыл бұрын
Had to mute the sound as the music was driving me potty, good instructional video though.
@R20Motorsports Жыл бұрын
yeah, these were early videos, and we were learning what sound to apply. Thanks for watching!
@Elias_619 Жыл бұрын
Dry ice cleaning is badass! Would love to try it out !
@R20Motorsports Жыл бұрын
Indeed! Thanks for watching!
@o0lunchboxxx0o91 Жыл бұрын
Clean it all you want but that tire is not street legal due to age
@R20Motorsports Жыл бұрын
Well we noted in the title they would be replaced. Never heard of any laws about tire age though…. :)
@1925sk Жыл бұрын
Hollywood.
@ruan800 Жыл бұрын
Think it's important to mention it is 4.4 US quarts = ~4.2 litres
@R20Motorsports Жыл бұрын
Good addition.
@eviltriangle Жыл бұрын
I drive a M2C and that video helped me to install a Grill. -If you have thin rubbery gloves (like from a Doctor) and have slim hands - than It's possible without removing the Top bolts. -I sprayed this gloves with silikone and this was the key..this way my hands were slipping through the grill pretty easily - whereas before I thought how?! -I was as able to open all Top Clips and the annoying 2 side clips (as mentioned in the video - these are key) -For the bottom ones, I did need a Pry tool that I used from the inside. So My hand was behind the grill, and I had to pry 2 of the bottom tabs from there. -You can build up a bit of leaver strength by setting he pry tool on the bottom area, which has a bit of stair like surface. Therefore, you're able to leaver that pry tool a bit. The whole process is much easier than I thought - but some of the tabs just need a bit of patience without pulling on the front grill like crazy, A gentle continuous pull should be enough with one hand - whilst you work through the tabs. Thanks for the video!
@R20Motorsports Жыл бұрын
Thanks for watching!
@AERO-ICE Жыл бұрын
Very nice
@R20Motorsports Жыл бұрын
Thanks for watching!
@AERO-ICE Жыл бұрын
very good work
@R20Motorsports Жыл бұрын
Thanks for watching!
@fatehgill9509 Жыл бұрын
What drill do you use? Lol I had to use a drill bit because the self tappers wouldn’t go through the bed liner
@R20Motorsports Жыл бұрын
Just a regular Makita drill. Maybe the drill portion of the self tapping screw was defective. I had no issues. Good luck!
@r.dwayne2067 Жыл бұрын
🙄 P r o m o S M
@Eferrari34 Жыл бұрын
Bravo! Best Easter gift ever!
@JasonSimonSmith Жыл бұрын
Whoa ! The undercarriage footage REALLY sells the car. Wow. Mad props to the Dry Ice treatment. Again.. Wow. Nice.
@R20Motorsports Жыл бұрын
Thanks for watching!
@rustybearden1800 Жыл бұрын
I would rather have this than all of the 356s, 911s, Cayennes, Panameras, etc. The 928 was the anti Porsche - absolutely love it!
@R20Motorsports Жыл бұрын
Thanks for watching!
@julioramos5842 Жыл бұрын
Awesome
@R20Motorsports Жыл бұрын
thanks for watching!
@RS3maniac Жыл бұрын
That used to be the jam!
@R20Motorsports Жыл бұрын
Yes it was. Thanks for watching!
@dancundiff3316 Жыл бұрын
Superb work, well done!
@R20Motorsports Жыл бұрын
Thanks for Watching!
@alexlabeda765 Жыл бұрын
Cool, might damage the control arm after a long time of doing that, but you're the professional. Maybe idk
@R20Motorsports Жыл бұрын
Not a chance. Dry ice is much softer than sand blasting. Aluminum parts can take full pressure and lots of cold.
@boa-sgt_reaperlivestreams5998 Жыл бұрын
Tf you mean sandblasting right, I mean any peace’s of dry Ice get on your skin and it’ll fuck your skin up and ik sand gets everywhere when sand blasting even if it’s contained lol
@R20Motorsports Жыл бұрын
This is Dry Ice, we wear gloves and its not a big deal. Much easier to deal with than spraying sand everywhere. Also much softer so we can clean wiring, rubber, plastic, painted parts, etc.
@ConspicuousLiveMedia Жыл бұрын
wunderbar
@R20Motorsports Жыл бұрын
Naturlich!
@Gregjohnshaftmansons 7 ай бұрын
Definitely