Robert Clever

Пікірлер

@CleverStuffTo 23 күн бұрын

This has to be the best Affiliate program out there. don't believe me then you need to check this out masteraffiliateprofits.com/tdf/YNYLZw?tid=tub

@iulianolariu1959 25 күн бұрын

I don't think that bend is the correct word. It's already bent and you straight it...

@CleverStuffTo 23 күн бұрын

Thank you for the input, I did test drive this truck and it drove like it should no more pull.

@billgoldberg5254 Ай бұрын

HERMOSA PRENSA HIDRÁULICA ...

@CleverStuffTo Ай бұрын

Thank you for your comment! I'm glad you found my video helpful. I'm always looking for ways to improve my videos, so if you have any suggestions, please let me know.

@bloxyarii Ай бұрын

Sometimes you can buy dumb tv's at goodwill and thrift shops.

@CleverStuffTo Ай бұрын

You are right about that cheap as well

@thegamingcomputer_68 Ай бұрын

It's SOOOO annoying when you start these things up only for it to turn on the connected HDMI device without your consent. Sure, you can turn off SIMPLINK, but that disables ARC devices, soo... And don't get me started on how big of a pain it is to set up these smart speakers with these smart ARC connections, unlike those old fashioned speakers that just... work. The only thing good about these new TVs is that you can watch KZbin directly from them. That's about it. And these things feel so slow. Like it takes a few seconds to load a menu, and on my smart TV, it just randomly pops up when I turn it on. Also, it keeps turning itself off randomly, which could be bad for my Fortnite sessions.

@CleverStuffTo Ай бұрын

It can be quite the headache, I agree.

@westcoastnaturalwolverine4068 Ай бұрын

They Live 😂

@breadmoth6443 Ай бұрын

id rather just have a dumb 4k tv , seems i have to look for a commercial grade display for that .... or if i could find a big enough pc monitors, i'll just use that .

@CleverStuffTo Ай бұрын

I'm sure there out there.

@lisat9802 Ай бұрын

My smart TV is hardwired through my router. I dont use it with wifi. I connect it via ethernet.

@CleverStuffTo Ай бұрын

Smart. that is how I did mine as well

@novdt Ай бұрын

I keep my smart ? tv in baby mode, It is not allowed to play with any other devices in the real world, aka: WEF take a hike ! only used as a monitor where i feed my DVRs, laptop and retro audio devices through multiple convertor interfaces. The AI feature is switched permanently off. As well, my security surveillance is cctv so i have control of my enviroment. have not disregarded the use of faraday shielding. P.S. all my AI cameras/ mics for TV,MOBILE and LAPTOP are phyically shielded, still use mostly all old school formats as well, cause if the net goes down...................Hmmmmmmmmmmmmmmmm

@CleverStuffTo Ай бұрын

I appreciate your concern about privacy and security. It's great that you're taking steps to protect yourself. Have you considered exploring additional security measures or consulting with a tech expert for personalized advice?

@colelundberg85 2 ай бұрын

This video is made with ai! Terrible video

@mikejungferman4744 4 ай бұрын

Dang dude that is a heavy duty solid tire, you couldn't hire some young man and say go to town, young men today don't know what hard work is, but we do , good job buddy

@CleverStuffTo 4 ай бұрын

Thank you

@kpsgil3118 4 ай бұрын

Anyone in toronto, ontario who does this?

@CleverStuffTo 4 ай бұрын

Not that im aware of

@kingjames8853 6 ай бұрын

Do you have a video of you pressing it off?

@CleverStuffTo 6 ай бұрын

I do not but since your asking I will make one

@CleverStuffTo Ай бұрын

kzbin.info/www/bejne/hpPGfJdvialoiassi=NC1SSimNGP5qydbS

@marleneprokopetz1857 8 ай бұрын

Thisbisban advertisement for generac. They are a decent convenient package, but a Honda gen set will far outlast a Generac. So, Generac for the nice convenient package, Honda if you need long lasting power. A howill last for thousands of hours of run time if you maintain it.

@CleverStuffTo 8 ай бұрын

Thanks, I would agree as well My Honda has been very reliable and I have had it for years at least 16 now But the Generac is very nice

@turbovw62rag 10 ай бұрын

hello, can i get more info please? were do i get this product? thank you

@CleverStuffTo 10 ай бұрын

you can find all the information here carlisletyrfil.com/

@kirkwiskirchen1827 Жыл бұрын

Where do you get the urethane and pump

@CleverStuffTo Жыл бұрын

The business that supplies the Product (Cat-Iso) mix will have the pumps. Either rent or buy.

@CleverStuffTo 10 ай бұрын

this comp. has it all prod. and equipment

@albertoroa01 Жыл бұрын

Does anyone know any shop in Chicago that can do this 😢

@CleverStuffTo Жыл бұрын

I don't sorry

@michaeljimenez7830 3 ай бұрын

ALopez tires 39 and Cicero Also Chicago Bus Truck at Bedford park

@dell7054 Жыл бұрын

Man i wish u were in texas.. I have a 2019 cascadia... no body can allign it... been to 3 shops. one shop added shims made it a little better.. Still pulls to the right. In wind its worse.. ALso rides like crap I My axle may be bent..

@CleverStuffTo Жыл бұрын

Can you take a pic of the alignment sheet you got I would love to see the results. and I'm in Arizona

@dell7054 Жыл бұрын

@Robert Clever OK one thing I like to ask is that my steering wheel has lots of play from the gearbox ..sometimes it feels tight and won't pull as much to the right and sometimes it's lose and it goes all over the place. Do u think my steering box could be worn out internally..should I change that first..??

@CleverStuffTo Жыл бұрын

@@dell7054 Sounds like it is wearing out and there are cases that the steering box will leak internally which will also make your truck have a pull I would get that checked out or just have it replaced that will at least take it out of play.

@dell7054 Жыл бұрын

@Robert Clever Yeah its been going on and off for about a year sometimes it's tight and lose the steering. New gearbox is around 1200 at the dealer and I can install by myself.. and then I will get an allignment

@wilboves4365 Жыл бұрын

Where’s your shop? Ph #?

@CleverStuffTo Жыл бұрын

Tucson AZ 520-888-6001

@rudolphtaylor352 2 жыл бұрын

Hey Rob good morning, what's your location ?

@CleverStuffTo 2 жыл бұрын

Tucson AZ

@CleverStuffTo Жыл бұрын

@Nouphanh Pravongviengkham Tucson AZ - STM Tires store 602

@hancockglen6307 2 жыл бұрын

I can testify that this will save you money. I have a 100 HP tractor for mowing right of ways and fields. The front tires always took a beating until we foamed the tires. This is a good video but I really don't think it is a DYI project unless you just want to fill some small tires on your dolly. Dollies always seem to have a flat tire when you need them the most. Larger tires should be professionally done and properly set so they are somewhat balanced. You don't go to fast on a tractor but the often will run 20 to 25 mph on the road.

@CleverStuffTo 2 жыл бұрын

Almost everything that has wheels is foamed here at my house

@RC-Heli835 2 жыл бұрын

Do you intentionally have .78 more caster on the right for a reason Robert? How did it drive where you were done man? It should corner well with that little bit of negative camber on both front wheels?

@CleverStuffTo 2 жыл бұрын

Well It should be -0.45 is the best but yes that is the side to side you want a little more positive caster on the right side, the side with more + Caster will pull opposite so it will help you stay straight for the crown of the road.

@RC-Heli835 2 жыл бұрын

@@CleverStuffTo Ok thx soon as I get a more accurate way to measure caster I may tinker a bit.

@RC-Heli835 2 жыл бұрын

Its amazing what all you can do with Beeline equipment!

@CleverStuffTo 2 жыл бұрын

I think it's the leading equipment.

@RC-Heli835 2 жыл бұрын

@@CleverStuffTo No doubt about it. Do you know of a good poor man's way to check caster?

@CleverStuffTo 2 жыл бұрын

@@RC-Heli835 amzn.to/47ik0DR I have this as well it will come with instructions on how to use it...

@RC-Heli835 2 жыл бұрын

@@CleverStuffTo Ok cool! Somehow I missed your reply I 'm gonna order that camber tool. I have found by measuring the spring plate in back and front of the U-bolts to the top of the frame that the right side caster is 5.76 degrees Positive and the left is 2.86 degrees positive by doing a little math. I also hit a speed bump once that caught me off guard and actually broke the right bottom leaf spring once and it took me about 1.5 years to get it fixed.

@RC-Heli835 2 жыл бұрын

How do you center the back axles on Chalmers 800 suspension like my dump truck has? Thanks great video! Do you have the axle bending equipment also? The last time my 07 T800 Dump Truck was aligned they couldn't get the steering arms apart so my wheel is not centered today? He couldn't get either side loose. I tried and couldn't either, they are stuck like Chuck!

@CleverStuffTo 2 жыл бұрын

Thank you for watching.. If you have the original parts installed should have an adjustable pipe on left side both axles. Like in my video start with forward axle and measure to a point on front axle by twisting the pipe it will move that left side forward or back, Yes I have the axle bending I show it on another vid. kzbin.info/www/bejne/apS3lJpvp7aGfKc and it is a hole lot easer to take the steering wheel off and center it that way.

@RC-Heli835 2 жыл бұрын

@@CleverStuffTo It has the pipes for adjusting forwards and backwards but I don't see any way really to adjust side to side. My front axle sits back on the left 3/16 farther than the right. The truck pulls to the right would that cause the pull? Thx!😀

@CleverStuffTo 2 жыл бұрын

@@RC-Heli835 there is no adjustment from side to side just the front to back rear axles should be parallel to each other. The front axle should be ok with that setback if more you should look to see if the center pin was shaved off. that will require lifting up the spring to see if the bolt is broken, next the pull will be caused either by tire air pressure, tire tread wear on the outer edge, brakes dragging or caster not right, a good alignment shop will let you know if its tire pull or alignment pull. If you want to try a quick fix swap your front tire left to right then take it for a ride if that fixes the pull you know it was tire related.

@RC-Heli835 2 жыл бұрын

@@CleverStuffTo Its pulled to the right ever since we got a little bit wider tires up front brand new. We had it aligned with a new set of slimmer tires before that set. They told us then that the camber on the left was .6 negative and 0 on the right but didnt gave a way to set camber. It didn't pull with those tires but was pulling to the right before alignment.

@CleverStuffTo 2 жыл бұрын

@@RC-Heli835 It does not take much ware for a tire to pull if it's toed in just a little it will ware that tire and create a pull. I would have to see the results of the alignment to see what they did camber out needs to be severe in order for it to make your truck pull

@CleverStuffTo 2 жыл бұрын

It took me 1 hour to press on 4 - 23.5 - 25's

@texfuz3727 2 жыл бұрын

Beautiful background play sir!❤️

@CleverStuffTo 2 жыл бұрын

Thanks

@CleverStuffTo 2 жыл бұрын

PWA is the way I think Anthony is on top of the game, yes you can try it out free but you want to make the big buck go with Ambassador Club check it out www.1marketingpro.com/webinarstarting

@andrewspears7107 2 жыл бұрын

LOL, it's funny that Jessica also started commenting on random videos as wellm and now she's raking $650 per week, lol kinda makes me mad since I was the one who told her to go'ogle the latest by Tanashie McStack and she's making more than me!

@CleverStuffTo 2 жыл бұрын

Wow What you going to do?