I use a valve face scibe. Work very well to transfer to the seat for contact location

I appreciate this video man. Started doing BIT inspections and going for a T8 ASE. This has given me a better understanding than other explanations I've heard. Great job!

Sorry to be pedantic but, you say 'it doesn't matter where the piston is, it's always going to be 100psi'. This doesn't sound right to me. Not only would the pressure change as the piston moved up and down the cylinder but the gauge pressure would change depending on the position of the gauge due to pressure at depth. Perhaps you meant this change would be slight and therefore negligent?

Leaving in the accidental hit was a good move. Great content earned a subscription and a like.

This is really helpful

Need some help with range selector on a super10 leak through both insert valves

Hello, What is the item number for that valve seat puller?

Ok

Great video thanks 👍

Do you grind valves for the general public?

Completely unrelated to car engines, but working on a hard seated valve (hydraulics) design. This was very useful. Importantly in my case the "interface angle". Opposed to the whole potential contact surface. Just reaffirmed the direction I was going. Well explained for an engineer.

Powerful info...👌

Thank your effort , its was so helpful to understand the steps to dis . and assembly this part of steering system

Bonjour,où peut-on se procurer l’extracteur de sièges (VALVES) si vous avez une réponse,je vous remercie.

If we removed the drive shaft between two differential truck still able to move ?

If we consider diameter of piston. Then we have to calculate area and then multiply divide with force?

Thank you very much. The explanation is very accurate and from a skilled teacher. This type of explanation is not available in KZbin clips. I repeat my thanks and appreciation to you.

Great vid. Where can I buy the tools to assemble the bearing adjuster and the locknut?

it looks like a Detroit 6V-71 2 valve bus application engine

You are a great teacher thank you

good info

We have a 4 stage cylinder that fully extends reteacts the first stage then dead stops what would cause that

Hello from where you buy this machine I need such a machine for working can you help me to buy

Masterfully done, brilliant explanation and you do make it look easy, especially considering that you use tools that are readily available that do not cost the earth

Thanks for all the videos posted. Very helpful to understand the mechanics of components.

I have a semi that when I put in gear it won’t move till I put in the power divider then it’ll move but just the rear not the front rears will turn. When the power divider is on the drive shaft will just spin from the transmission. Any help?

Very detailed nice video Thank you

Awesome demo. The preset valve guide installer was nice. Will have a machine shop make one for my requirements 👍

Good day very enlightening video need that information very much i have older eaton 15 speed trans and changed my shifter it was leaking air pretty bad added new 5/32 airlines and new a4688 slave valve been scratching my head the slave valve when i shift to low side it leaks air and at 1st doesnt want switch over to the low side been in shop 2 days and mechanics are not figuring it out So today purchased new air filter / regualtor and watch your video i believe i might be close to the issue had bit of moisture going threw my system and i believe i might need to replace shift range cylinder o rings any insight will be very appreciated also will purchasing new pin and spring and sleeve kit behind the slave valve thanks a million great video new subscriber

It’s amazing how many people don’t know how a differential works. Throw it in as an inter-axle and people lose their minds. Great explanation though!

I think mine is leaking oil between piston housing and transmission

Good informative video

Wow left Sait eh. We need them knowledges

What is the rotation if pressure is in port A?

OLÁ. PARABENS. Até hoje, 19/12/23, esta é a ÚNICA EXPLANAÇÃO CORRETA QUE VÍ NA INTERNET. Eu poderia acrescentar algo prático, talvez pouca coisa na parte econômica, mas não o farei em RESPEITO A SUA CAPACIDADE TÉCNICA. ABRAÇOS...Roberto Udo Krapf

Any max speed recommendations on inter lock.some ppl keep it locked at all speeds

i need bay this pl wher

Muchas gracias colega, donde se puede conseguir el manual de mantenimiento de la bomba de dirección hidraúlica TRW, gracias.

You a good teacher man thank you

Nice explanation sir 👍👍

What type this vane pump?

I have good battery, it's 12.6v holds charge I just need to test the alternator it's the 3rd one i installed now there's 8.8v coming from the PCM wires to alternator so when I ground the other wire to see if increase in voltage at the battery but nothing. Today I will bypass the those wires his time put 12v to alternator and tap the ground again to see if battery increases to 14v.Any ideas are greatly appreciated.

Perfect example straight to the point love it i have no idea how i got here but thanks

The homemade tool makes this video even more valuable, Thank you!!

Thanks for the diagram! I'm having an issue with my converted 13 speed rtoc1609a. When in a high split going to the next gear in low (after preselect) it grinds and I'm having to feather the throttle a lot more than normal to get into gear. Normal shifting in the 9 speed pattern without using splitter and also while downshifting with or without splitter and no issues. Also notice constant air release from exhaust port when master valve is in high split position. Would a rebuild of this system be in order or could it possibly be an issue with ecm timing due to converting from the 9 speed to 13? Thanks!

❤

Hi , where can we get that pulley tools please 🎉

is this for sale

Why didn't you explain how to reinstall the rack gear and input shaft. I'm trying to figure that portion out

I’m looking for a double acting cylinder just like that, how can I get specs and availability information ?