Princes FPV Drones

Пікірлер

@KimberHall 16 сағат бұрын

get to the point already!

@idiotsnifff Ай бұрын

Hey dood, wondering if you have a tune for this on betaflight 4.5 or 4.5.1

@PaulSokolov Ай бұрын

Can you help me with BLHeli 32 settings for 2808 - 1900 kv motors. Which PWM frequency the best 24/48 and which Motor Timing

@brianthekid9 Ай бұрын

Hi there, am looking for someone to build me a custom racing drone for 6s or 8s for $200, i can pay if you can contact me, thanks

@bladeystudio 2 ай бұрын

I’m glad this worked for you my system is the same except goggles2 and maVic air 3 and can’t fpv

@tonypena1 2 ай бұрын

How was the event?

@princesfpvdrones 2 ай бұрын

It was amazing!

@derqatarzan4207 3 ай бұрын

What ya use to tune this bad boy? Would ya mind sharing ya setup?

@gcarmichael 3 ай бұрын

Will the RC Pro Controller have an image on it while you fly with the goggles? Example: I would like to have someone else wear the goggles while I fly with the image on the controller screen. Are both images active?

@BirdWhisperer46 3 ай бұрын

PERFECT @ 14:13. I have a couple Phantom 4's and just spent money on a Mavic 3 Pro in delivery as I speak, and finding it impossible to find any size comparison. Until now. Thanks.

@BirdWhisperer46 3 ай бұрын

WRONG, first thing on a new site is to reset the compass.

@harrylode1 5 ай бұрын

Important question, what happens if signal loss, The mavic is coming back home?

@odessa1799 6 ай бұрын

Hi, your flight with goggles is incredible. My question: DJI spec. states that Integra not compatible with remote controller RC-N1 or RC Pro for Mavic 3. Only need to use DJI RC Motion 2. Kindly respond if you have any problem to pair controller with Integra

@princesfpvdrones 6 ай бұрын

Yes, a mere message you ignore but it binds fine.

@odessa1799 6 ай бұрын

@@princesfpvdrones Thanks for respond

@edman1015 6 ай бұрын

Do you know if the goggles will work with the Mavic 3 Classic and DJI RC controller with the screen?

@princesfpvdrones 6 ай бұрын

Hmm, I do not have had those drones but certainly worth a try.

@nickhemphill 7 ай бұрын

Anyone able to get the video to appear on the DJI RC Remote Controller and the Integra with the Mavic 3 Pro? It always disables the controller's screen when the goggles are connected. Disconnect the goggles and the screen works again.

@Rocketryman 7 ай бұрын

The recording of this video. It does not film. That is a different piece of hardware.

@narendhraarjun7041 7 ай бұрын

2500 kv does it support 6s

@chrisalexthomas 7 ай бұрын

I really wish I found this video a week ago when I got my version of this frame. I found a couple of things I found was weird is there are no instructions. They couldn't just print out a diagram? Take a look on youtube for a build video, the official video literally about building this frame skips over the part where it builds the frame. It's absolutely ridiculous. Secondly. You got the Mr Steele version right? So I bet you also ran into the issue that the little motor feet you get in the box don't even fit the frame? I don't know who thought of this frame design, but it's clear to me that nobody was really professional, or serious about it. It's just a bunch of parts in a bag, not even a box. Some of the parts in the same bag don't even fit on the frame when it's assembled. I'm glad to see you flying and it was smooth and nice though, so perhaps once I get over those issues I'll find it's also a nice frame. It's just annoying had badly put together the package was.

@princesfpvdrones 7 ай бұрын

Yes, it was a struggle but through a lot of work got it to work and I agree with your assessment. Looked like just a money grab by the looks of it just because has Mr steel name on it.

@chrisalexthomas 7 ай бұрын

@@princesfpvdrones yeah, I think it’s gonna be alright when it finally gets constructed, it’s just a shame cause missing the mark on big issues is understandable, but failing to do the smallest, easiest issues is a sign that nobody really gives a shit and maybe if I had known this beforehand, I would have gone with a different long range frame cause then I would get a premium frame with somebody who put effort into making it… I still can’t get over it’s just a bag with parts and not even a schematic in with it… mind blowing considering this is €130!

@LovesM855A1 8 ай бұрын

I love my AOS frames

@princesfpvdrones 8 ай бұрын

Oh yes for sure!

@fyzobaba 8 ай бұрын

HOW LONG DID THE DRONE SURVIVE? AND HOW MANY AMPS WAS THE PROP PULLING ON TOP SPEED?

@princesfpvdrones 8 ай бұрын

Oh I still fly it from time to time, everything is still fine!

@fyzobaba 8 ай бұрын

Nice. trying to build one but the 2700kv motor not available. Maybe i will use the tmotor pro V 2550kv motor on 6s. Thanks

@fyzobaba 7 ай бұрын

@@princesfpvdrones hey did u reduce the Ramp up power of the esc to somewhere around 25%.

@princesfpvdrones 7 ай бұрын

All settings are the description.@@fyzobaba

@fyzobaba 8 ай бұрын

TOO MUCH VIBRATION.

@monacocross4241 8 ай бұрын

GOOD VUDEO QUOLITY YOU SEE IN GOOGLES WHEN FLY ?

@FiveHourFriends 8 ай бұрын

I love flying my Mavic 3 with the goggles but it limits video frame rate to 60 fps. If i use your setup are all the other video frame rates available?

@princesfpvdrones 8 ай бұрын

I find it has no effect on what you film at when recording to the drones sd card.

@Rocketryman 7 ай бұрын

@@princesfpvdrones 2 weeks ago I find it has no effect when recording to the drone's sd card.

@Flying_Wild_Boar 8 ай бұрын

Thank you for the video! I really enjoyed watching it. I'm curious, what distance are you able to achieve on the stock antenna o3 ?

@len9483 8 ай бұрын

Is there any way to use Mini 3 or 4 Pro controller with the goggles ... while ALSO viewing flight on the Ipad? I want to fly it while my Wife wears the goggles.

@jameskelly9579 6 ай бұрын

Goggles 2 has a video out designed for a phone or tablet.

@dnn79 9 ай бұрын

So after months of opportunity to fly without the motion controller, and just connecting with the regular transmitter, has anyone had issue with connection loss of tue drone as DJI states? Thank you

@princesfpvdrones 9 ай бұрын

Not experienced that or heard of that.

@dnn79 9 ай бұрын

@@princesfpvdrones good to know. DJI has stated it, so wanted to see for sure. Thank you.

@DronieBoy 9 ай бұрын

Great video but this doesnt work with the dji air 3 and the new RC2

@princesfpvdrones 9 ай бұрын

You mean controller for the 04 system?

@DronieBoy 9 ай бұрын

@@princesfpvdrones correct

@princesfpvdrones 9 ай бұрын

I don't have the 04 system so I cannot test this set for 04.

@PatricksDIY 7 ай бұрын

It actually does work, I have that setup and it works fine, Also with my Mini 4 Pro. First your Turn on your Drone, then your goggles, pair the goggles, after pairing the goggles, you turn off the goggles, and turn on the RC2 controller, you then take off like you normally would with your RC2, and then after its launched you turn on the goggles, and it works. The only thing that is a slight inconvenience is you will see a message stating " Aircraft only supports DJI RC Motion 2" on the bottom right of the screen and my RC 2 controller also still shows the video feed. This is with the most recent firmware/software as of todays date.

@princesfpvdrones 7 ай бұрын

@@PatricksDIY Thank you for explaining the steps so well!

@jeffdughman9741 10 ай бұрын

im using the xing 2506 1500 kv , they are super great, give them a go and make a vid on it :)

@princesfpvdrones 9 ай бұрын

@powerhouse884 10 ай бұрын

It works with Mavic 3, Mini Series and Air 3 drones.

@princesfpvdrones 10 ай бұрын

Yes the Mavic 3 and mini series drones.

@powerhouse884 10 ай бұрын

@@princesfpvdrones And the Dji Air 3. It was updated as well.

@princesfpvdrones 10 ай бұрын

@@powerhouse884 Well, that is great news!

@dortmunder27xxx 10 ай бұрын

@@powerhouse884Hallo.Does it work with DJI Googles V2?

@zlachannel8674 10 ай бұрын

How was the durabilty of the motor sir,,does it can handle a few crash/hit

@princesfpvdrones 10 ай бұрын

Yes, yes it does!

@markgiles8527 11 ай бұрын

You have to take off before you can connect the goggles?

@princesfpvdrones 10 ай бұрын

Yes before you turn on the goggles.

@RandoManFPV 11 ай бұрын

Real sad i cant find a video jist visually showing off these motors 😮 your pics are the best i got other than the stock xing photos from the sell listings online

@princesfpvdrones 11 ай бұрын

Yes, these motors are amazing! Glad I could help!

@Ace-dh5lz 3 ай бұрын

Pretty sure these are 1800 not 1300

@RandoManFPV 3 ай бұрын

@@Ace-dh5lz nah I went ahead and ordered the set. They say 1300kv on the side but the lettering is real bad, 3 looks like an 8

@renerjose4753 11 ай бұрын

nice presentation sir! after installing the latest firmware to all the respective gear in this video, i assume you have already “paired” the goggles to the mavic3 before performing this “special” boot up sequence?

@renerjose4753 11 ай бұрын

as a follow up have you also tried using the RC-N1 with the Mavic3 and goggles integra as well?

@princesfpvdrones 11 ай бұрын

Yes, that would be correct.

@ibilyy 6 ай бұрын

@@princesfpvdrones how did you bind mavic 3 pro to integra? My integra just shows "Connecting to mavic 3 pro..." and not connecting

@d369studios 11 ай бұрын

Thanks 4 sharing the video !!! Wish you offered to build mods for others, the difference is truly amazing!

@princesfpvdrones 11 ай бұрын

Yes I agree, totally, hoped my video helped you.

@flyinfilm90 Жыл бұрын

Nice build... Identical to mine

@princesfpvdrones Жыл бұрын

Oh really?

@flyinfilm90 Жыл бұрын

@@princesfpvdrones Speedy Bee F4 , Vista VTX , Axis AF236 Motors, 6s

@AtradiesInc Жыл бұрын

Is it a fast ripper

@princesfpvdrones Жыл бұрын

It sure is!

@Mary-bs3rq Жыл бұрын

Inconceivable!

@len9483 8 ай бұрын

Vizzini: I can't compete with you physically, and you're no match for my brains. Man in Black: You're that smart? Vizzini: Let me put it this way. Have you ever heard of Plato, Aristotle, Socrates? Man in Black: Yes. Vizzini: Morons.

@umbroraban1075 Жыл бұрын

Thanks for sharing all this. I took a bit of figuring out to assemble my APEX 7" Steele version. It was a bit easier as the camera supports for the DJI 03 unit were included in the kit. I have got all set up and I have done a first LOS flight. Looks good and powerful on the 6S battery with the 7" props. I have noticed that the quad is a bit twitchy when moving the sticks. Did you take the default BF tune of did you adapt to fit the 7"? Thanks and happy flying!

@gonzarb93 Жыл бұрын

where can i find the 3d printed parts? and how many parts of each i need to print

@princesfpvdrones Жыл бұрын

You and me both would like to know, I got this from off from Facebook Marketplace already upgraded. Sorry, but maybe thingverse may help you out.

@jg3331 Жыл бұрын

Hi Thanks for that great video!! Can you zoom while wearing the goggles ?

@princesfpvdrones Жыл бұрын

If you mean flying, then yes, you can fly fast or in sport mode with the goggles.-

@p.0788 4 ай бұрын

Yes this possible in the explore mode

@brentsheldon8667 Жыл бұрын

I have the ul7 for about 6 months. The frame is very cool looking, but I wouldn't buy it again because the arms are very fragile. When you have any kind of wind it seems more problematic then a more traditional frame.I This quad is very difficult to get the mid throttle jitters tuned out of. My chimera frame is a much better 7-inch frame. *** I would like to say that I love Chris Rossers videos and have his Aos 5 inch frame, and that flies better than any other frame I have.**

@princesfpvdrones Жыл бұрын

Well, I do have to agree with you there on most all of your points as that has been my experiences as well.

@YaroDrone 26 күн бұрын

Great, so - again, Rosser's frame are good in theory but in reality they are vibrating and oscillating more than traditional frames made of thick hi-quality carbon. I had AOS5 frame made by Iflight, happy to switch over to Syncmode as that was impossible to tune vibration maker, inspite of all the "super-rigid truss structures". Now he released new UL7-8-10 frames, and I considered switching my chimera7 build to UL7 frame - but happy to stumble upon your comment

@georgep.9014 Жыл бұрын

Can you zoom while wearing the goggles ? I haven t seen you use this feature.

@teerawattang5071 Жыл бұрын

While the RC is doing the maneuvering of the drone, do all the buttons on the RC still function as usual ? Do the buttons on the goggle Integra also function ?

@princesfpvdrones Жыл бұрын

Yes, yes they do.

@RandoManFPV Жыл бұрын

ios options or???

@princesfpvdrones Жыл бұрын

I have not tested this yet on Iphone and certainly not on the latest OS but with the 03 system I no longer need to use this set up.

@RandoManFPV Жыл бұрын

@@princesfpvdrones yea I couldn't find an ios solution. I ended up using cosmoview on my pc. How does 03 system remove the need of digiview? I've heard so many good things about 03 I might upgrade but I'm really new to fpv and rc..and even computers honestly so all this is well over my head Currently I have cadx vista on nazgul5 hd v2, dji goggles v2