Had a similar issue on my car. We weren’t able to get it fully seated with the wrench but close.. put the wheel back on and torqued to spec. Would that have pulled the stud in more to make it seat? Is it safe?

15/16 is 24 mm

Thank you very much for this video. It was extremely helpful. Any chance you have a video showing how to replace the fog light on a Disco II?? Same year as the one in this video 2000. Thanks!

holly fuck a car video in 4k

Video helped me with this exact same issue. Thanks alot

What’s the fuel pressure for a dodge stealth es 1993… Because they gave me 2 options 60 Psi and 100 Psi

Thanks - great job explaining

how did you know you need to replace it your steering gear? i am hearing noise from my front tires when i turn the wheel. i can't tell where it is coming from.

how to setting routing cabling from dekstop to monitor planar sir...

Bedliner rattle can would look really good on this thanks for the video I got some old bed rails might try building one

"Weed, sammiches n jerky".....sounds fun

Would I be able to undo the line at the bottom without taking off the tire? Where my car is sitting I won’t be able to do that. Can I just jack it up and go underneath?

What issues did u have on a bad box? Im having an issue not sure if its because of this. But steering wheel seems to over correct pretty bad and truck moves left n right on a straight steering wheel. Have alot of new front end, ball joints, tires n alignment good

Holy rusted metal, Batman!

To Nissan frontier 2001 3 3l v6

Where can i finder stering gearbox seal

😔

I need this.. how can i find this./?

What’s it cranking before you did that

You could hear the relay with pulling it out. But great video I’ll be changing mines out today. Thanks for the demonstration

Nice job. Mine is a manual gear box (no power steering hoses) so this shouldnt take me long

Fucking SLAYER!!!

Thank you very much, for your video.

Piss poor video 💩💩😁💩😁😆💩😜

So what about the hydrolic hoses? Do I have to worry about getting air in the system?

Good job but it covers your tail light.

Nice video! did you ever work out what why the car wouldn't rev? I have the same issue on a freshly built motor 3000gt that has sat for a few years. I'm replacing tank, pump and filter, will also blow line out as you did. Hopefully injectors are ok. Was your reving problem to do with fuel in the end or something else? Thanks

about to tackle this on my d21 1996. look very similar.

Hey I've been looking everywhere but I can't seem to find anything on this. I just bought a 93 Stealth, it has a bad crankshaft seal and and for some reason I can't get the alternator to mount correctly as well. Is it possible for you to send me a picture of how your alternator is mounted? Again, I cannot seem to find any info on the 93 Stealth, and with a bad crankshaft seal I can't drive it to the shop and I'd rather avoid paying for a tow and diagnosis. I would really appreciate the help. If you want you can just email me at [email protected]

what did you use to make the video not shake? Looks great.

Thanks for making this, I might be buying a non-running Stealth soon and this will be useful

do you remember the exact name and brand fuel pump you got

Was your car cranking and not starting before you did this? My car a 1992 Dodge stealth es with 156,878 miles.

weed, a sandwich, and some beef jerky and he's set for the week haha, I laughed too hard at that

Nice video and thanks for sharing!

I want to make something like this but to fit two Jerrycans, side by side, behind the wheel well in the bed of my Toyota truck. Two Jerry cans should pretty much be equal to a full tank.

@ Bud Slayer : you ??

Thanks much for the video.

well done i have the same problem and ai dont now how to fix the problem.Thank you very much.

looks good

hey, who's the idiot that ran out of gas??? what a dummy!!!

play some futkn slayer!