Erik Cendejas

Пікірлер

@the_bencredible 27 күн бұрын

This is how I know the whole “FBI guy” thing exists. Last night I was texting a friend about buying his invidia downpipe for my 2013 STi. Now this shows up in my recommended. Coincidence? I think not.

@JoseCoyoteLopez Ай бұрын

Firmeee asfff ehhh

@CendejasCustoms Ай бұрын

Yessir my dawg

@stevenruiz5367 2 ай бұрын

Placement and installation of the switch wasn’t explained or shown. Is it meant to go there and do you cut anything for it to sit there where you placed it?

@escobaroutdoors3693 2 ай бұрын

Bro thanks for this video! I'm bagging mine now and this one helped alot!!!

@CendejasCustoms Ай бұрын

Glad I could help!

@sti_clone3840 4 ай бұрын

Dang sounds good :) , ya haven’t posted anything in awhile but hope you’re doing well!

@tee7200 6 ай бұрын

Upload more videos on lowering trucks 🔥🔥 I can watch this all day

@henryjackson2555 7 ай бұрын

That swich should not turn your compressor on and off After the bags reach the prefect ride hight. So that switch should not be needed.I have an (accuair (e level )suspension setup with air lift bags and that is not in the setup. So check online,youtube! And see if there is a difference. I doubt that it is. That's something that was andded.

@LefthandTriggerman 9 ай бұрын

Great vide. Question... What's underneath your Grom for the bike to rest on when dropped? I just bagged mine, but it doesn't rest on anything. So I still gotta use a kickstand

@agustinhernandez3314 9 ай бұрын

Where did you order your flip kit just need it for the rear?

@pete699669 9 ай бұрын

How long is your stretch?

@lsbzcuz 11 ай бұрын

dont see anything about water trap

@galinkrastev4427 11 ай бұрын

What' does the drain plug do in the side of the manifold..is it for air or for water .if it's unscrewed would it air the car out

@stephenm.french8380 Жыл бұрын

I've owned this exact pressure washer for several years but just bought a brand new car in 2022. I've been afraid to use the 2800 PSI because all the professional car detailers on YT videos say don't use anything above 1100. I refuse to buy another pressure washer just to wash my car. I think with you video, I may give it a shot. I got scared when you used the yellow tip on the front grilled because it's 15 degrees. Thanks for the video.

@bigfam5362 Жыл бұрын

How to start the pressure washer

@igotvisage Жыл бұрын

Air lift no longer sells the rear bags that secure to the top and bottom…

@AshleyHernandez-jq7gu Жыл бұрын

Hey do you need to flush out the anti freeze ? Or will it flush itself out ? And if so how would you flush it out ? Thanks !

@tehkz Жыл бұрын

I believe it manually flushes out over time from airing up and down

@codymarschinke9383 Жыл бұрын

You bottom out?

@savagekarma6397 Жыл бұрын

What size of stretch and chain did you run...

@pete699669 Жыл бұрын

This what I'm here to learn as well.

@savagekarma6397 Жыл бұрын

@pete vermillion I went with a 420 and it was too small by like 4 links.. if I was you I would go over size and get a chain cutter tool like I did and size it yourself

@ericktorres8948 Жыл бұрын

is the rear and front separate kits?

@dondc2827 Жыл бұрын

I need both side vents where can I get it painted

@planedr Жыл бұрын

Must be a union job. 5 people watching and getting in the way and 1 person working. 😂😂

@willsiegel8018 Жыл бұрын

shouldn’t you keep it up over night so the bags don’t freeze/crack?

@xuanquoc6178 Жыл бұрын

Hey how to got it to sitting on it own whe.n u air out?

@XenkKenny Жыл бұрын

What do you do to keep your air compressor from freezing?

@BrandonCockridge18 Жыл бұрын

2 gay ass cars and 2 gay ass drivers

@agungriyadin1112 Жыл бұрын

Hello brother.. may i know what suspension do you use for the rear suspension? how long and what brand? where to buy? Thanks

@whitehammeer Жыл бұрын

Do you still have your Grom??

@user-vl4pk9os4n Жыл бұрын

Jc75 and jc61?

@PeachCoastLowrider Жыл бұрын

glad I found this video , always wondered how to install a water trap . soo my tank has two lines coming out and into my manifold..is this really necessary ? or could I use one of the ports for something else like train horns or an air tool line like yours

@thebusinessguy5985 Жыл бұрын

You don’t need to replace the manifold, if it’s out warranty anyway (or not) you can replace the board mounted pressure sensor on the PCB for the affected channel

@grahamwood8447 Жыл бұрын

@@ejmatranga8622 to fix the fault you need to either replace the manifold (the black box) at a cost of around $800-1000 or you replace the pressure sensor with respect to the faulty channel inside it. The part can be sourced from Honeywell.

@KingCuzo04 Жыл бұрын

I fucked up my splitter and popped my driver side vent off going down a curb yesterday, shit happens I guess

@NikaidouStep Жыл бұрын

What offset are you running on this wheels?

@CendejasCustoms Жыл бұрын

+10

@samwallace8876 Жыл бұрын

How does the antifreeze reach all the airlines if there is a water trap stopping all liquid from leaving the tank?

@bleedzacid Жыл бұрын

I’m wondering the same thing

@ericsmiller88 Жыл бұрын

The Schrader valve is connected directly to the tank from underneath, and the antifreeze doesn't go past the tank. The antifreeze helps prevent the condensation that your compressor creates from freezing in your airlines and in your valves

@MrTheHillfolk Жыл бұрын

It's methanol,so it probably evaporates into a gas....haha ,like if you probably disconnected a line from out at a bag and held a lighter near it you could light your ciggy 😄

@djkarloshouston Жыл бұрын

I was having that issue a lot bacn then.. but im prety sure i found the issue, normally you get that warning when you have over pressure in the tank, the manifold gets into safe mode and sends that code... for example, i go to gym and leave my car getting direct sun and with high tempetures, my tank being in full pressure and getting heat, the pressure expands, and the manifold enters in safe mode or pressure sensor fault. i made an experiment, and left the car again with direct sun light and high temperatures outside the parking lot, but this time the solution was to leave the tank half empty, and there you have it. . no more faults.. and i did notice the pressure was higher than before when i came back from the gym to my car. . remember you have some water in the tank, and with the heat the water condensates and creats more air in the thank....im so sure airlift knows this, but i bealive the dont say nothing about ot bcuz they run a bussines and that type of stuff gets the more manifod purchases when the manifold its not under warranty no more. I hope this its helpful for anyone out there having headaches bcuz of that pressure sensor fault thing lol .. and just to let yall know i havent got that issue any more, and i did not change the maifold either. and just for the record I run the 5 gallon tank and 2 compressors.. yalls may be diferent but its the same concept.

@djkarloshouston Жыл бұрын

@spt_killerwood Жыл бұрын

Hey I just got my bags on this past weekend. Just started experiencing the same issue. I think you may be onto something. Bc it's been hot here the past couple days and samething is happening to me. I get off work and it's hot in my car. My psi is reading around 220 in the tank and I'm getting that warning. I park in a gravel driveway so I don't air out. It stays at ride height and when I get in my car after work boom I'm getting it. So I'll try and drop it some to reduce the psi and see if that works. Thanks for the info

@vincent5076 Жыл бұрын

Thank you so much bro. I didn’t rlly want to send in my manifold and wait for a new one. W.

@djkarloshouston Жыл бұрын

@@spt_killerwood Yeap ! till this time havent got anny more issues or warnings.. another thing i tried its to set the max pressure on 25% less .. lets say mine its 200psi max.. i set it on 175% and it has worked for me .. so i dont have to be airing out manually. and if the heat creates condensation inside ths thank i wont pass the 200psi for sure 👍

@djkarloshouston Жыл бұрын

@@vincent5076 yea man, i was the same way, cuz to get airlift to send a new one and all that is just a hazzle !

@spt_killerwood Жыл бұрын

@@djkarloshouston yea after I commented on your comment I went and changed my psi to 180. Since then I haven't had any more issues. Everything is back to normal. Thx for the help I appreciate it

@JorgeHernandez-fw7qm Жыл бұрын

Did you have to delete abs on the bike?

@CendejasCustoms Жыл бұрын

Only thing I had to bypass was the kickstand man

@Idkmaybeoneday Жыл бұрын

@@CendejasCustoms how can I get in with Steve?

@CendejasCustoms Жыл бұрын

@@Idkmaybeoneday Just updated Steve’s website in the bio man! www.mangumelite.com

@brandonrivera1425 Жыл бұрын

did he have the original 17 inch wheels

@brayanramos644 Жыл бұрын

Link to the water trap?

@FlossyZach Жыл бұрын

Do you have a link for the water trap?

@juanaguinaga5733 Жыл бұрын

Im having the same fault pressure sensor but my compressor won’t turn on either even if I manually try to turn it on and when I air up on that corner the air leaks out of the manifold

@thinhle8974 Жыл бұрын

replace sensor fix done

@ginocaccese8705 Жыл бұрын

How did you end up fixing this? I’m having the same problem at the moment

@bama25625 Жыл бұрын

Sameeeeeeee here!!!!!!!!!! Help!!!!!!!!!

@ginocaccese8705 Жыл бұрын

@@bama25625 you’re unfortunately going to have to just buy a new manifold altogether. i had to use a separate compressor and air tank to just fill my tank since my manifold was in safety mode. there are inflation valves you can buy for your lines: part number is 21633. you can use those until the new manifold comes or until you can send it out to get it fixed. but unfortunately there’s not fix unless you know how to solder and can figure out how to replace the sensors

@bama25625 Жыл бұрын

😭😭😭😭😩 not good. The guy I bought the car from is trying to get in touch with air ride maybe somehow someway he can get me a new on thru warranty but we will see!

@Luizmtz5.3 Жыл бұрын

How do the shocks ride? Debating on those or air shocks

@peppermaster1189 2 жыл бұрын

Thank you so much for not sounding like a complete idiot. Every video I have seen on this topic has someone that just makes themselves sound dumb. “He bout to put the WCI on der like dat”. I can’t take anyone seriously when they sound dumb. I appreciate when I can understand what you’re saying. I believe people that use the words F€£K and BRUH and FININ every other word have absolutely nothing important to say. I went through 5 videos that started with the person saying “BRUH” or a variation of it. And the 3 that started with “IM FININ”. And 5 more where they couldn’t get a sentence out without saying “BRUH” at the beginning or ending of every sentence. And swearing every other word. It’s nice to hear someone that can explain what their doing, without sounding like a complete idiot. Without making themselves into a walking MEME! After watching this video I’m going to go through and watch the others. Keep up the good work man. I know the younger crowd wants to here that dumb dribble leaking out of the buttholes they call mouths, but I promise that there are a whole lot more that want to listen to someone who can explain everything without sounding like a moron. And you are doing things that other people aren’t. Like explaining the wiring. This is something that everyone skips over. They are trying to get it done as fast as possible so they can show everyone they have a bagged Grom. Not taking the time to show how everything was put together or how everything works. And I think it’s super cool that you had the foresight to include this important topic in your video. I’m serious when I said keep up the good work. You can really be a great motorcycle reviewer. I know I would watch the living SHIZ out of you vids. Great content, great subjects like bagging a Grom and you would make a great host. You should do it!! I already subscribed and I will definitely be looking for new vids. You could do motovlogs and ask local dealerships if you could review their bikes. It would give the business free ads and give you new bikes each week to review. Again!!!!!! KEEP UP THE GOOD WORK AND I LOOK FORWARD TO SEEING MUCH MORE FROM YOU!!! Also, ride safe brotha.