Heat Transfer Channel

Пікірлер

@muhammadabidrazzaque5741 2 ай бұрын

Thank you for this useful information

@muhammadabidrazzaque5741 2 ай бұрын

Good information 👍

@viettankhuu4668 3 ай бұрын

Can you share what the main reasons are for PHE leakage into the atmosphere when putting in service after re-installation? Look forward to hearing from you. Thanks.

@TamunoOpuboCooksCookeyGam 4 ай бұрын

Can Connectivity be put in place in other Plate heat exchangers? Is Connectivity available for Alfa Laval Spiral Heat Exchangers?

@Olivia-ii4jo 7 ай бұрын

When replacing a gasket, does one need to use adhesive or petro gel or maybe neither?

@udeshwijesekera3898 8 ай бұрын

Thanks for the teach that sir...

@jacobgartung9074 8 ай бұрын

How heat exchanger do for phosphate?

@Citizen435 10 ай бұрын

How to clean the plate heat exchanger without removing it (on site). Which chemical to use? Do a video?

@mohamedimranimran3413 10 ай бұрын

Hai sir good morning you are videos only help me lots during PHE work.. I have one doubt regarding PHE cleaning I was try to cleaning plate with pressure washer after I using pressure washer couldn't clean it properly using a pressure washer.. It is very black and dirty Sir Please recommended something better 🙏

@MarkLucas 10 ай бұрын

The Darcy-Weisbach correlation you use to relate Delta(P) to velocity is more tailored to pipe flow. Works great for a shell-tube, not sure how valid it is for a PHE. Are there more suitable ways to theoretically validate pressure drop for a PHE?

@avika88 11 ай бұрын

Hi is there a chanse to still get access to this tool for educational purpose?

@exofura Жыл бұрын

basic stuff, great presentation but, most people prefer ignorance...

@gert_kruger Жыл бұрын

Is there simulation models available to simulate pressure drop vs flow?

@desmondaubery8446 Жыл бұрын

Thank you very much. Excellent video.

@desmondaubery8446 Жыл бұрын

Thank you very much. Excellent video.

@desmondaubery8446 Жыл бұрын

Thank you very much. Excellent video.

@QuincyIndico-xt2lv Жыл бұрын

Would like to request for phe leak test overview

@mohamedimranimran3413 Жыл бұрын

Hai sir… I’ve few questions regarding plate heat exchanger.. How I’ll contact you?

@sheremetbyevo Жыл бұрын

Excellent explanation. Thanks.

@eurobrowarriormonk7182 Жыл бұрын

More silliness. a snake eating its tail. you need the heat in winter. however in winter cold is available for free to cool the centers. Using energy to cool the centers in winter to produce heat for heating homes is such a waste of energy.A snake eating its tail

@SG-tt5fs Жыл бұрын

How can we repair air gaps on body of phe?

@trocadordecalor Жыл бұрын

👋👋👋👋👋

@mawathageseneviratne3226 Жыл бұрын

thanks for information, need to know how capacity selection.

@mohamedimranimran3413 Жыл бұрын

Hai sir I've few doubt on plate heat exchanger can you explain me?

@heattransferchannel8474 Жыл бұрын

Yes, sure

@mohamedimranimran3413 2 жыл бұрын

Hai sir how are you? I hope doing well Sir we are mostly doing plate heat exchanger servicing. It’s very hard to loss and tighten the plates sir we are losing and tightening manually only sir. Is there any equipment and tool for tightening plate heat exchanger

@heattransferchannel8474 Жыл бұрын

Yes, there are either pneumatic or electric tools that can be used to loosed and tight heat exchangers, and we use them regularly.

@dominicnobel8709 2 жыл бұрын

Hi sir

@bikicviki 2 жыл бұрын

Thanks! Nice video! Do You have some video which explains differential switch and how it works as heat plate exchangers flow security device? If I good understood, differential pressure switch wait until the flow make enough pressure drop and press it. This is information that flow is good. I expect if the temperature of fluid drop that pressure will rise and on the end if it is frozen the pressure drop will be max and the pressure switch will be stile pressed? Where I am wrong? Thanks in advance ..

@vg1803 2 жыл бұрын

First of all, excellent videos, it's clear and simple, thanks! What value should we aim for for the wall shear stress? I read in an Alfa Laval document about the best design practices that ideally 50 Pa would be necessary with a minimum of 35 Pa for a fouling applications. Is that right ?

@heattransferchannel8474 Жыл бұрын

Sorry for the belated reply, yes 50 is a good number and 35 should be considered as a bare minimum for fouling applications. If you are absolutely sure that fouling is not going to be a problem, though, you can live with much lower shear stress

@christiancooper6071 2 жыл бұрын

How do you find the safety factor ?

@dianheatexchanger547 2 жыл бұрын

Thanks.. 👍

@mehmoodurrehmanahsan1348 2 жыл бұрын

Dear Bestio learn Sir, Hope you will be fine. Can I Access to this software for learning process. I am from Pakistan.

@heattransferchannel8474 2 жыл бұрын

Dear Mr Rehman Ahsan, I suggest you can in touch with Alfa Laval Pakistan

@prashantmaniupadhyay6337 2 жыл бұрын

Great video Sir. Much appreciated. I am from India. I want access to the software. Thank you

@heattransferchannel8474 2 жыл бұрын

Hi Preshant, the best way is to get in touch with Alfa Laval India, we have a very strong presence in your beautiful country and every region has slightly different requirements

@arifshaik8959 3 жыл бұрын

very useful information sir, you are making the concepts clear by visuals. Actually less videos are there on plate heat exchangers concept, But you are helping a lot. Thank You sir.

@Khabbazhadi 3 жыл бұрын

how should we calculate the appropriate thickness of fix and movable frames and the number and size of bolts for specific GPHE model at specific operating pressure like 16 bar?