Are your tunes locked from modification by the end user? Not sure how to word that question. For example, i have stock injectors. If, when the time comes and i need to replace them, i choose to buy 10% over or 30% over, can i personally fill in the data on the tune to let the program know i have a different size injector? Or am i calling you for a new flash at that point?

Why would you delete your transmission cooler. Did you add one under the truck?

It was a PITA! Getting the plastic plug out was difficult. My tool slipped, and I stabbed it straight into my radiator. Yeah, now I need a new radiator. I fixed one problem and created a new one! Lol

I didn't get a ding notification after doing the key off an on.

there is a product called GIT Rot. it is a 2 part epoxy thats very thin like water which will soak into rotted wood and then harden.

Epoxy to what? Rotted luan and styrofoam

Do you have a product number for the barb you used to connect the 3/4 hose to the 5/8 hose?

i’m following this step by step , any reason why it might not be working ?

Ive been looking into buying a mm3 kit with a few of your tunes. Im thinking the 60, 90, 12v 120, and the 160 I want to go with. I was wondering if these would all run good on a stock 05 common rail. My truck was nv4500 swapped by a previous owner and is running on an unknown manual swap tune no (PRNDL) display. Would your tunes accomodate the 5 speed as it only mentions an nv5600 for the manual swap options on your website. Thank you

My oil gauge works? Thats news to me 😂😂😂

Thanks for showing the part numbers on the tools, it made my trip to O'Reilly's way easier

How tight are the bults?

My 2007 ram with a 5.9 cummins has the odometer in the speedo cluster not under the tach, I cannot get this to work

We don’t even put TP in the tank. Closed lid trash can empty everyday.

Dose the 12v tune help injector longevity with only having one injector pulse

Mdpe

Thanks for the great video made it so easy

Yes Helpful. Thanks

what does status ff mean when quick learning

Is the only fix adding an analog gauge with the sensor mounted in the pan?

Thanks for the video. I have a question if I may: I have a 2009 Dodge Ram 2500. If I hit the lock / unlock bottom on the driver side door, only the front doors will lock or unlock but not the rear doors. Any ideas ? I find it hard to believe that both door actuators went bad at the same time. Thx

Mine reads 60 at startup. Hmmm time to do analog guages

Actually you can fill the stock diesel tank right to the top but it takes forever as diesel will foam. This mod allows you to fill the tank right to the top very quickly.

Good video, thanks. Everyone should just put black electrical tape over the factory oil pressure "guage". At times the factory voltmeter is not accurate either. An easier way to prove the factory oil pressure gauge is a fake, is to unplug the connector from the oil pressure sensor just above the ECM on the engine. Then start the engine. This makes for a good laugh!

It was water that caused the problem.Impossible to dry it out. I don't know how the expoxy can work when it is wet.

What programmer you have on your dashboard

I deleted mine also and it works great ! You saved me alot of $$$$$. I thought you were talking about thermastate on engine. I changed mine on the engine and it use to run 180’. Now it’s 200. I wish I wouldn’t have changed it

what exhaust setup are you using?

I flipped the thermostat and WOW. Pressure went up and shifts are firmer and better.. Totally worth it.. Working on the heat exchanger now. God bless you all!

Super, soldered the 2 middle transistirs, now the gear selector working

2005 ram 1500. Doesn't work. Tried it many many times

How do you get rid if the backup horn ?

Would a failure in this cause a hot fuel line coming off the cp3, rough idle, and 23k psi at idle?

The 5.9s if working correctly should throw a abs light when the wheel hub goes bad ..or you should jack them up every 2 months and give them alittle shake to check ...... If you don't catch it in time you can watch your wheel pass you going down the highway ;) good luck friends 🙏

Gotta keep one on hand in stock if you wanna have one of these trucks ;)

Does the fan turn off when temp is met?

Does the fan shut off when ac temp is satisfied?

Pull the rear speed sensor , top of diff, bet it has dust stuck to it (inside) clean it and change diff fluid

Would it be the same process on a 2006 Cummins 5.9?

How do we contact you?

Mine pulled the wire out of the plug anybody know what wire goes in what holes?

Do i need the com mod to operate this mines a 06 5.9 my smarty did not come with this

What's your current contact email for tuning etc?

Thanks for sharing. Delimitation can seem like a daunting task. Your video made it seem a bit less intimidating.

I assume you will want to dry out the area first?

I was thinking of deleting this completely for heater core as I installed coolant bypass wondering if piping to the heatercore would help to keep truck cooler as return Enders top side of motor Or deleting it all together and plugging the 90

Cool iam going to try it based on your video

This doesnt prove anything, the exact same test will work with an open differential. Adding brake gives both tire equal resistance meaning they both get equal power.

what should the minimum operation temperature of the transmission be?? No one can tell me?

I did what you said and it worked! Thank you.