Smart

Bread is the best

You're genius ❤

Super 🎉

I’ve tried this multiple times never gotten one out 😢

Thanks for not keeping this to yourself.

After the puller I brought that's designed for this job failed to retrieve the bush. This did the job. Thank your sir!

Man that's so cool

👍👌🫡

Like the upgrades

Where did you source the cup holder?

My bolt+nut would shift diagonally and the nut would slip off the back lip of the bushing. So I used a larger bolt and an over sized nut, ground the nut down to the inner diameter of the bushing an thinned it to fit behind the bushing, and finally ground a flat on one side. That worked perfectly.

This didn't work for me. I ended up renting a slide hammer & puller and had it out in less time than I spent messing w/this.

Thank you fore the tip ❤

esto merece mil likes jajaja

amazing,

Perfect!!!

Grease and a plunger wat it in hydrrolic it out

I dread the bread 🍞 this is awesome!

Thank you very much! I bought a needle bearing puller but that didnt cut it. Tried woth grease aswell but to no avail. This worked!! Thanks!!

thought u were gonna attach Slide Hammer to Bolt somehow > well done, Sir

I learned a much better way of doing this just use a larger fine thread bolt and it will make it's own thread and drive in till it hits the back of the crankshaft then it will pull the pilot bushing or bearing out!Just center the bolt and the soft bushing will let it work it's way in

Thank you. This trick worked so well on my car that it took me longer to find a suitable bolt&nut than to get the spigot bush(ing) out.

Awesome!

ピッタリなサイズ見つけるのに時間が掛かりそう

i was taught to spline aligning tool and grease it comes right out

Awesome

just full with grease put a bit of dowel in the hole and hit the dowel. easy.

I'm just here to see how many people know the Grease method?

🌹🌹🌹👍👍👍🌹🌹🌹👍👍👍🌹🌹🌹👍👍👍🌹🌹🌹👍👍👍🌹🌹🌹👍👍👍👍🌹🌹🌹🌹👍👍👍👍🌹🌹🌹🌹👍👍👍👍🌹🌹🌹🌹👍👍👍👍🌹🌹🌹🌹👍👍👍👍

Super!💪💪💪

bread works too keep bashing it in and out pops the bearing

Great idea

Very clean build.

It's good to know, i don't think bushing coming out crooked is an issue.

Theres not many bushes of this type big enough to get a decent nut through the diameter of the bush

How would you press a new one in without a press?

I just get a bolt that is tite in the bushing and ratchet it out

Genious

Awesome idea 💡

wow😮......genius ! 👏

Good trick.

Brilliant! - oh how we used to struggle...another idea that we used was using a Rawlbolt (expanding bolt used in wall fixings in the UK) and that worked but you had to buy one, whereupon this is by using odd bits laying about in the workshop or toolbox. Great!

Thank you, had tried grease and slide hammer to no success and this worked a treat, thank you

Very useful. Thank you.

Run a 5/8 tap in the bushing, comes right out

Nice work! 🙌

Put a slice of bread in the hole and as you hammer it flat with a drift in the middle it will push it up and out ,it works every time...

I’ve removed plenty of those over the years. Easiest way I have found is pack the hole with grease, find a piece of wood dowel rod that just fits inside, line it up and give the dowel a good smack with a 3 pound hammer. The pressure forces it right out. Works every time

You can also fill the hole with bread and use a rod the size of the hole and drive it out it works I've done it