Great video Shaun. I have a couple of valves reading .22mm on the exhaust (.02mm over spec) and .16mm on the intake (.01mm over spec). The bike has a little over 12k miles on it, with maybe 500 being track miles. It'll be my race bike for next year, so do I need to adjust it?

What does the o-ring do cuz when I googled it it says that it doesn't need one

Or you could use a tiny embedded micro controller with a program loaded that converts the Haltech freq to the OEM tacometer freq

Mine starts with starter fluid only ,does that mean its electrical?

Shaun, Date: 01/03/2025. I have a 2017 Aprilia RSV4 RR with 17,000. miles and I have not done yet the Valve adjustment to it. what tools do I need to do the adjust. what is the procedure to do on a 2017. and finally do you have a detail video on how to do it. step by step. thank you and a happy new year full of health.

Did this fix the tank pressure issue?

Thanks for making this video! going to buy mine now for my 748!

what torque for the bolts with spring?

its only for track use?

Is this limited to your year bike? The reason I am asking is because I have a 23 PANIGALE v4 and was wanting to do this myself but new to these bikes.

Hi. I have an aprilia rsv4 rf 17. Can I do timing with the engine on the bike?

May I ask why the penetrating fluid wasn’t cleaned off before assembly?

Hi Shaun, thanks a lot for your video. What is your front stand model because mine touch the front fairing and even the air duct input, i would like to change it :) thanks a lot , i feel ready to do the same fork operation now :D

This video is very helpful with out it i would have not done my conversion. Is it normal for the clutch lever tension to be a little stiffer than a wet clutch? I just did my streetfighter v4s and the clutch lever is stiffer. Thanks

I need a 2006 Kawasaki 650r gas tank ang pump do you have forsale

What lube did you put on the seals that are in the engine cover? The water pump and crankshaft seal that sits in the engine cover?

I love your videos. I actually did the valve clearance inspection on my RSV4 a few years ago by watching your videos. It's just about that time again.

When checking clearance did you havd to loosen Cam tensioner first? Or check them with tensioner still in place?

Just looked at those links. None of them are longer there.

I don't remember the owner's manual reading that, no wounder I could never get it. Been on RAIN since I bought it. LOL. Anyone know how to get the speedo to work, mine just stays on ZERO all the time?

I see what you did there with the beginning of the video

So glad you stayed on-board. Well done. Did you have any traction-control engaged?

Your big orange hammer 😂😂

Bloody noisy innit

Can’t thank you enough for this video. I just bought a pristine ‘09 that has this issue. Hoping I can do this repair myself…

Many thanks for the video tutorial, Shaun. ✊ Helped me resolve a service warning issue.

And I thought that I was the only messy mechanic

Hi Shaun, is there anyway I can contact you regarding a clutch issue I've got going on?

Si quieres ver cómo desmontar un motor de la forma más chapucera posible…, este es tu lugar! Viendo el desmontaje; entiendes perfectamente el estado del mismo.

Could you do this with the injectors still in the bike?

Hi Im working on Laverda 650 with P8 ECU could you please share your knowledge , how to get the ECU program and adapter cable .? Many thanks

Is it better to pair the Zumo to the Packtalk or to your phone? Thanks:)

What tool did you use to remove the db killer

Hi Shaun, Thank you for all those very informative videos, especially the previous one showing how to move the cassette. I also broke my sprocket bolt yesterday.. drill it, used an extractor and... the extractor broke as well. I'm screwed. I will have to remove the cassette and change the shaft I guess.. How did you manage?

Shaun, whats the reasoning behind the chrome pro for a track bike apart from just because, Is it the data logging and ability to review what your doing?

Great tips for cleaning track suits. Had my Alpine Stars out this morning for my 1st ever ride in a track suit , and all went well. Now just need to have many more to break in all my new gear , Shoei full , AlpineStars boots , and Taichi gauntlets . Doing all these runs in Texas Summer 🥵 in prep. for Nate Kerns Track School . Thanks again. for sharing these care instructions. Lexol is good leather conditioner . Used that on bridles and saddles at horse racetracks.

Why does every other vloger say R is race not rain, who is right, and who is wrong whay does it say in the hand book?

Thanks for the coaching session Shaun! Hopefully catch you out there again in September!

My bike speedo isnt working. I dont know if front or rear wheel speed sensor if fault or even the abs module is faulty. Can guzzidiag rectify and identify accurately on which fault is causing 0 on my speedometer?

How can I try out coaching at kartmoto

Hi I have a question: my problem sometimes is bad hot start….cold start is perfect bike working perfect nothing else just sometimes after riding I stop on drink or to fuel up and when I start my bike start so badly like almost shuts off itself and then come alive again in 10sec something like that…so I do some research and find that is probably that charcoal canoster making that bad hot start that ppl are removed and have wonderful life…..do I need some Canister Eliminator or what should I do….anybody some info!? Thank you…..❤

I got the same bike same year thats been sitting for years. Only 300 miles on it😞

Thank you! I have one of these jigs but didn’t know the set screws were drilled to also be a guide. i learned something! Appreciate your video.

What was the cause of the crash?

Got this working following these steps. Initially, I tried doing it without the factory reset and the units would not connect to each other. I then tried a factory reset on both units, and they connected exactly as shown in the video. To get your Packtalk into Bluetooth mode, either a) Click the intercom button (wifi logo) and phone button (phone logo) together on the headset, or b) In the Cardio app on your phone, select Intercom (2 blue helmets), then press Bluetooth at the top of the screen. When in Bluetooth mode, the headset light will slow flash blue. If it's still in Mesh mode, it will slow flash green - you want blue! After the factory reset, the G9x headset will be listed under Intercom > Bluetooth on either channel A or B (depending on which channel you pressed during connection on the G9x), but its name will be generic. You can rename this via the app. Once connected, you have to activate the connection by either a) Press the channel button on the G9x (exactly as per this video), or b) In the Cardio Packtalk Bold app, under Intercom > Bluetooth, press the channel the G9x has been saved saved to (either A or B). For me, the intercom audio strength between the two heads is strong with good line of sight distance of 500m+. Connection between these two heads work very well.

I might be having the same issue with my VFR 800, thanks for the info, I’ll try the same thing hopefully it helps…

Good learning experience nonetheless 😅

Merci 😊✌️

I love you