Hej, jag kollade trycket igår och såg jag att den är under 1 bar (05). är det något fel elr bara för att det är sommar nu?
@janive113 ай бұрын
Thank you for sharing this video! I was able to fix all my volvo v40 cc doors. It was great to see you fail at the first time because it happened for me also with one door. I knew that it still might get fixed if I keep doing it because you were also. :)
@erikteigland985 ай бұрын
Hvordan??🤩
@dennislohr56726 ай бұрын
Some extra information: (1) The actual length from the door panel to the T25 screw is about 86mm / 3.4in. You will actually need a shank that is slightly longer. (2) The 5 turns is good advice, but you will also feel a slight resistance in the turning when you get to the correct point for stopping. Do *NOT* force the screw once you feel this resistance!
@outrospection4all6 ай бұрын
Work of genius - i bet even the local Volvo dealership don't have your skill and knowledge
@social_lag6 ай бұрын
My door handle is now broken thanks
@flameR202326 ай бұрын
Thank you so much, I am just having the same problem! Very useful video!!!
@gujongujonsson96716 ай бұрын
How do you link Plejd to Hue,are you using Homebridge on computer with it?
@mikaelstrand156 ай бұрын
Toppen! Stort tack
@mateuszkos34576 ай бұрын
Does it work the same in xc70 2016r? I have keyless go but with the rubber buton on handle ?
@jacobwiqvist17606 ай бұрын
It depends on what you mean. It is another way to renovera handel on XC70 V70, and another way on the neder models.
@mateuszkos34576 ай бұрын
Yeah. I know that is other way to remove the handle but i asked if its work on the same way. It's about rust in the connections and whether it can cause the door not to close when you click the rubber button. In my case, the door opens, the problem is with closing it.
@jacobwiqvist17604 ай бұрын
Basicaly yes!
@helllsing847 ай бұрын
USER ERROR!!!! Herregud, ladda inte in profiler!
@MohammedHaidar-wi9jj7 ай бұрын
Jag har Nibe F730 men har inte fliken (Service) hur tar jag fram den?
@MohammedHaidar-wi9jj6 ай бұрын
jaha okej nu skall jag testa göra det tack så hemskt mycket!@@mrhulk.0101
@qosmio9747 ай бұрын
Thank you very much, video is still helping :) Fixed my front passenger keyless on V40 2013 :) Working smooth after first try !
@teropa797 ай бұрын
I think this part of zibomod should be in focus for coming releases. The autopilot / autothrust modes work ”okay” but either the FM or some calculations or most likely both are off.
@teropa797 ай бұрын
You are just seeing that the flight model is too draggy in lower levels. It causes the need for thrust bursts during descent. And especially strong slowing down if you take a direct. The flightmodel drag, vnav path calculation and resulting path is not correct.
@75STARFISH7 ай бұрын
Thanks dude, this is really useful information. I was thinking about getting two of these for a twin stick for Elite Dangerous. This explains the £99 price point.
@jonathanlarsson14067 ай бұрын
Kan du göra en video om hur displayer i rummen funkar? Mvh
@tysonristau49958 ай бұрын
This is normal with lower end joysticks, they aren’t that good. I’ve ran heavy equipment, it takes awhile to figure out the nuances of the hydraulic controls and dead zones. Maybe you could pretend that this joystick is acting like a real joystick 😂
@oinoink8 ай бұрын
Om värdet faller med t ex 20? Vad har man för fel då?
@teropa798 ай бұрын
Very nice demo, well done
@nespecificiran8 ай бұрын
Hi man, thank you for a great tutorial video. I have Volvo v40 2013 and i assume that they have a same problem and the same fix. I going to try that tip, hope that works for me also.😊
@electromic60049 ай бұрын
Thank you, mate. My V60 has the same problem. Hope I will solve it ) Regards.
@goldenwayLasse9 ай бұрын
Lite nyfiken på om du fick klarhet i vilken inställning det ska vara i meny 5.1.14 vid golvvärme bottenplan och radiatorer övervåning - är själv konfunderad över detta och kan inte hitta något bra svar?
@jacobwiqvist17609 ай бұрын
Jes still an issu!
@shittychannel48609 ай бұрын
Tja! Inte ens Volvo själva kan svara på denna fråga, så hör med någon som äger en MY24 XC40 Recharge. 1. Fick du med en Shucko/vägguttag:s laddare till bilen utöver typ2-typ2 sladden? Samt, finns det ett 12V uttag i skuffen/bakluckan? Tack!
@eeroolli9 ай бұрын
Many thanks very good advice! Three door locks later every keyless working well now :) excellent know how video😀👋
@svettparre10 ай бұрын
Ääääääääää 😂😂
@teropa7910 ай бұрын
Is this still an issue you have? I am considering Brunner MKII for Zibomod. But if the SW support is totally random, I guess it's too much money to experiment with?
@Hellooow9011 ай бұрын
Du är bäst . Du har sparat mig 12 läh!
@jacobwiqvist17609 ай бұрын
Mig sparat 7000kr!
@gimmejr11 ай бұрын
This just started with my driver side on my 2013 t5 s60, Ill give this a go. 93k views, hmmm I wonder if there should be a recall?
@Beachbender343 Жыл бұрын
Any tips on how to get the left back door handle to pop back in place at the end. Was able to do it on right hand side. Left hand side, I tighten the screw and handle doesn’t pop back to flush (normal) position.
@haroldhughes5883 Жыл бұрын
"Promosm"
@agronbuqa1492 Жыл бұрын
Hej. Does it work if I start the lights with a normal switch, then turn the lights of by the dimmer switch when I get to sleep. And when I go at work and come back home to turn the lights on by the normal switch again, even if the dimmer switch it's off?
@ValKillYa Жыл бұрын
V60 2011 it did not worked for me. In my case, keyless is not working for front doors only. Rears works completely fine. Surprisingly at first try, rear also stopped working as in clip. I tried switching door handles around - still no luck. Help would be appreciated.
@jacobwiqvist1760 Жыл бұрын
Sory to hear.
@dennislohr56726 ай бұрын
I believe there is Service Bulleting for the 2011 models. The wires are too short.
@hoagybob Жыл бұрын
Dielectric grease might work. Electronics on volvo cars are problematic because of where the wire looms and connectors are manufactured .......Italy.
@Drmerlin604 Жыл бұрын
Good to see that the rudder and tiller has finally been fixed. I thought that the problem was nothing to do with ProSim and was totally an MSFS problem according to Lapi. Curious because he is NEVER wrong.
@jacobwiqvist1760 Жыл бұрын
It is a MSFS problem, so he is right in that regard. But all of flightsim history developers have to do workarounds due to limitations i flightplatform. I also have to use a extra program to fix the tiller. The extra program "FSRRudder Fix"should have bin implemented in ProSim long time agoe. All other developers have done work arounds to get rudder tiller to work.
@Drmerlin604 Жыл бұрын
@@jacobwiqvist1760 That is really helpful to know. Can you tell us a bit more about the rudder fix software that you use, where to get it and how to install it? Thank you so much.
@bmkoster24 Жыл бұрын
I have a 2016 V60 D6, but the keyless doesn't work on any of the doors. Also i have to put the key in the ignition to start, it wont detect the key at all. My first thought was the key battery, but i replaced the batteries on both keys and they still don't work. Will this fix it?
@joajo4587 Жыл бұрын
How long does the torx t25 screwdriver have to be?
@Tjarven Жыл бұрын
Visar verkligen hur värdelösa Torix är på alla sätt. Bra video för upplysning.
@nahranavidea Жыл бұрын
Thanks, all my S60 handles are working again. I also had to do the front door (watch out for the driver's door - you need to push the little beak underneath, which is there because of the door lock)
@Beachbender343 Жыл бұрын
Beak?
@ollelood6614 Жыл бұрын
Jättebra video och tydligt vad som krävs för verktyg för att genomföra. 😊👍 Jag behöver dock få loss förardörrens handtag för att spraya kontakten även där. Hur får jag loss den lilla hylsan för reservnyckeln? Denna måste tas bort för att få loss handtaget. 😊
@ollelood6614 Жыл бұрын
Lyckades få bort hylsan till låset genom att skruva ut skruven något mera än fem varv. Tack för mycket bra video! 👍
@Jordsmed Жыл бұрын
Finally worked for me! Tried 4 times. Didn't work. Decided to follow one of your comments saying that you should try with the front door if it didn't work. I hesitated BC. The screw hole was stuffed with a plastic filler. Decided to remove it. Lucky it can be put back on again easily. Did it one time with the front door. Now it finally works! Thank you so much. Volvo V60 2011.
@BlazejHollylodz Жыл бұрын
Do you think this will fix the same issue in V90?
@yannhenry4314 Жыл бұрын
Thanks a lot!!!!
@anders8018 Жыл бұрын
Thank you, worked like a charm 😃 Probably saved me a lot of money…
@Beachbender343 Жыл бұрын
I’m having trouble on my S60! Back drivers side, can’t get the handle to pop back to normal after taking all steps described in video. The other side back door handle did pop back into place after I performed the maintenance. But the other side just won’t pop back when screw is tightened.
@alanmanzoori Жыл бұрын
Hi Jacob - this is an excellent instructional video - really really clear. Should this also work for a 2016 XC60..? I've found the hole to the handle, used a T25 Torx, pulled the handle out and turned the screw five times, but I cannot get the back part of the handle to pop off as you've shown - and I am reluctant to turn the screw more in case it drops within the door... Is there some other trick I am missing? Thanks in advance!
@qosmio9747 ай бұрын
I had to make it around 8-10 times before I was able to put it out. Also noticed there's a metal barrier to prevent dropping the screw.
@olahansen Жыл бұрын
Skärpa är överskattat!
@Dankmaister Жыл бұрын
Hur återställde du detta ? fanns där något överhettningsskydd? jag har ett flöde på ca 175 hela tiden, men igår när vi bröt strömmen på några faser så stannade vår externa fläkt som levereras med värmepannan just nu pga restnotering. efter det har larmet uppstått. larmkod 325 som jag sett att du haft.