This has worked well for us but your paddle board fin mount needs to be compatible with it. So, whichever motor you get, make sure they have a mount that works for your board

@@MYuen gee … thanks for that quick reply..

If you have them both connected and you connect an appliance to it, they will tend to balance out after a while so that the percentage of the battery remaining on both will be roughly about the same. So if you had an appliance drawing, let's say, 400W,the extra battery will tend to deliver about 200W to the Power Station, which will deliver 400W to the appliance so after a while the capacity of both will tend to be about the same.

@@007alztruli Thank you , I assume that your answer is based real experience with EcoFlow extra batteries 😁👍

@@raedalshaye4062 Yes it is. I have the Delta 2 and the Extra Battery. When I run appliances with the 2 of them connected, if both batteries are full, it normally starts pulling power from only one of the batteries - usually the Delta 2 (though I have seen it pull from only the Extra Battery too sometimes). This usually goes on for a while till the battery is down to the 65 - 80% range, then the Extra Battery starts charging the Delta 2 while it is still powering the appliances. If for instance, the total draw from the appliances was around 400w, the Extra Battery might deliver about 600W to the Delta 2 (D2), so you'd have 400W from the 600W of the Extra Battery (EB) going to power the appliances and the remaining 200 charging the D2's batteries. This will continue till the EB's remaining battery capacity is close to the D2 then it will start reducing its output gradually till the remaining battery capacity of the 2 are about the same and then it will start delivering about half the pull from the appliances so they will both run down at about the same rate from there. Maybe with much larger loads, the EB might start much earlier.

Why do you have one? Lol

Yes, it should work via the HDMI port

How is this video a scam? The article I posted in the description is very comprehensive and shares with parents what worked for us in having 2 of our kids start to bike quickly

Please read the article linked in the description

It's been good, but I've found myself hardly using it unless I'm camping and need the lights

It depends on your needs. The Yeti 6000x has 3x more battery capacity than the Max 2. With that said, stay tuned... Goal Zero has a new product announcement coming October 3. I suspect it will be their long awaited, updated power station

Hi, what do you mean?

@@MYuen amz test

@@alan4631Ah, no thank you

You figure this out? I just spent an hour trying to route the wire and gave up 😩

Maybe you guys figured it out already but I don’t you can actually thread it through the right pillar. What I did was slid it behind the window trim. Sort of like how you would hide a rear view camera cord as you are working your way to the back. Hard to explain without photos lol. It actually hides it very well! It’s out of sight.

@@Swiftest87 I did, I bought the shortest fish tape (12m) on Amazon for $12 and fished the wire. It took less than a minute 😉. The hardest part was getting the connector through the grommet but I took my time and was able to get it through.

@@markbranderhorst5802 I'm glad it worked. I'm not sure if all the panels are the same or not. I took my phone to see the opening and it did not look like my '23 XSE had enough room to shove a connector and a wire clothes hanger line in that opening. Either that or I'm not going in the right spot. Probably also why the video cuts that part out because they had a hard time or went another route.

It's generally a liability and warranty issue to tinker with settings consumers may not know what they are for. So, many companies won't publish it because ultimately, they may be asked to warranty something that the consumer broke as a result of changing the settings

@@MYuen Changing auto-sleep doesn't do anything, whether it is 0 or 3 or 60. Bike still shuts off in 20 seconds or faster. Even bigger liability issue is having the bike shut off while moving, and not being able to change the settings so PAS 1 is not max speed of 20mph. Do you know of any way to reset the bike to factory default? Many of us used the Heybike app to change settings, but some settings were changed that were not supposed to change and now the app doesn't work.

@@TheUsflow i never got the app to work 😂

@@TheUsflow I don't have the bike any more, but I imagine that contacting the manufacturer might be a good option. Regarding reset, I usually just set back to what I have in the video, but don't know if the app allowed additional configs not available from the control panel

I no longer have the bike, but what I'd do is change the settings to the same ones as shown in the video and see if that returns it. If not, you may want to contact the seller or manufacturer for additional assistance.

It's for sure a huge difference in brightness: 300 ANSI Lumens (Capsule 3 Laser) vs 1,000 ANSI (Mars 3)

Hey Jen, I no longer have the bike, but I'd look into: P05 PAS Levels (higher than 0-5, if available). P12 Assist strength. Make note of the defaults for your bike before you change. Some settings shouldn't be modified as that could invalidate your warranty and/or cause damage to the motor

Hi Jen, I’m getting my ranger S tomorrow, I take it the programming changes ( top speed) worked on your bike? I noticed the cityrun control looks just like the ranger s, thank su

My buddy who did the review for me has had it for 9 months now and still using it