Bro u driving around with no lights on how dafuq can u see

This has convinced me to not try this project at all. I do not get wiring and this further convinced me I don’t and will break something or deploy my airbag. In all sincerity thank you for showing me how to do this because otherwise I might of attempted it.

bought this same setup for mine, thanks for the video

i daily drove a 02 WS6 for over 12 years with a Yank 4200 stall 7 of those it had 323 gears the last 3 were with 410s damn that car was fast i did have a big hayden tranny cooler never skipped a beat the 4l60 was built once and freshened up once in those 12 years eventually the LS1 engine let go but not the tranny or Converter

Oct 2024 price. 2001 Z28 auto 103k miles for $7500

I would love to see a video detailing how you swapped from the 93-99 style steering wheel to the 2000-02 style. Even the one without the wheel controls. I prefer the 4 spoke style of the 2000-02 wheel and want to swap it into my 99 Z28.

How much does it cost to fuel and how far can you go with full tank?

It is important to put the axle under load to make it easier to put the links on. I tried it with and without the load, and the links fit much easier with the axle holding the weight of the car in a normal position. I also used a bottle jack to slightly raise or lower the axle to make the links fit even better. More videos should mention this technique since it is not always obvious to the viewer where the jack / stands are located, frame or axle or both.

Chevy is the king of cheap interiors, instrument switches buttons all low grade junk. Plastic crap.

I have a 1999 Camaro Convertible and I have the top down most of the year, in the summer its in the morning on the way to work, in the winter it on the way home, spring/fall sometimes both. Get the clear uv film put on those t-tops, it blocks way more than factory GM tintied glass but doesnt hinder vision through it,,

😂

Why did you take off the valley cover?

I just ran the bolt from the bottm with the nut on top so i dont have to drop the subframe

I have a 98 z28 very clean 50 k miles . Get it out once in an awhile . Very fun to drive. Good adrenaline rush .

very clean🔥

that bolt is such a pain to cut, probably the best way to do this though. thanks for the info

I just got my hands on a 99 z28 ss, with 47k original miles

Except tail lights falling off ! 😮 my Z28 never fell off, and its a 95 ! Dash board cracks, check..roof needing to be repainted check, ride height, check...all were present on both my '95 Z and my 2000 WS6. Don't forget the infamous 10 bolt rear 😢 Now as for the window motors, yes they are slow, but if you want to make it easier rolling them up, open the door when rolling either 😉 side up. Makes it so much easier on the motors 😮 Nothing is perfect brother But your SS sounds and looks great. Just learn to take the good with the bad, give and take.

😂

man why tf my truck got totaled nd i was tryna figure out what im gettin next & one of these popped in my head. this a sign 😭😭

Happened to me when i was working on my Volvo 240. Changed the alternator and the car wouldn't turn on afterwards. Crank sensor wire got pinched between the block and the frame and shorted out 🫨

😂😂😂

Just so ugly

I’ve got a 02 Camaro SS that I THINK has a bad o2 sensor. It’s in limp mode now after we’ve had some tremendous rain. Would a bad o2 sensor cause limp mode/misfires?

my 1995 z28, the dash has no cracks in it. Its stored 6 months out of the year for the climate i live in.

try that on a 2000 camaro 3.8 no room

My buddy had one of those back when we were seniors in high school! Brings back good memories 👍🏻

I read that the windows are heavy and that causes the motor to wear out quicker. I got lucky with mine and my dash isn't cracked.

Camaro jump

I'll keep it simple for everyone the only thing GM did wrong was not give the SS more HP

he is right about tail light lens falling off. and burning oil is normal.

What year is your Camaro?.. I have an 01' and was wondering if it has an MLS from the factory or composite head gasket.. Is your original head gasket MLS? Thanks

How are the control arms holding up ?

What rotors are those originally from? also what size washers?

Works really nicely with a procharger or turbo, keeps it in boost!!

Hopefully that Camaro found a new owner

These cars are easy to slide even unintentionally. The reason you’re having difficulty has been mentioned in the comments, limited slip doesn’t work so well on yours. Of course it’s hard to slide with only power going to one tire.

Being able to daily driver a loose converter really comes down to what you can tolerate. I drove a 3600 around for 6 months and hated it because it always sounded like I was hauling ass every where I went. Fun as all hell but annoying to go to the grocery store or take the kids to school.

I just bought a 99 Chevy Camaro and notides after I got home the rear sway bar Is not connected Its just there and it hangs down a bit too low for my comfort but I got It from a family member very cheap.Thanks for posting this.I wonder If I can buy just the bushings?

How's the UMI kmember holding up? Did you get the regular one or the road race one?

Were you get the turn signal assembly from

Does your steering knuckle seat all the way down? To the rack

4l60e?

Nice Camaro! I love those cars. I see less of them and at one time they were everywhere.

i summer daily drove a yank ss3600 for over a decade with an ASA cam... no problem. it was fun as hell.

What wheel spacers did u use do u have a link?

I had the Yank SS3600 in my '00 WS6. I daily drove it and loved it. I miss that car.

Unfortunately a decent amount of audio had to be muted because of copyright…. If you have any questions leave them in the comments down below.

Morning Buddy! Are you interested in doing some product review projects? Check the dialog! Talk about more details.🤝

What cam are you running?