Quick tip, after disconnecting the intake hose from the throttle body, always put something over the hose so that you don’t drop something the inside of the hose and cause a bunch of mayhem trying to rescue it!!! Good video though!👍

cum ai setat intinderea curelei din intinzator?

ai dat in suportul ala in incercarea sa-l dai jos? Parca asa mi se pare. 😀

Hi I'm writing to you from Italy, thank you very much for your tutorial without it I would never have succeeded, on KZbin there are other similar videos but not as well done

Salut! Ai idee de cine sunt produse intinzatorul si pompa de apa originale (daca scrie)? Urmeaza sa fac o si eu si ma gandeam sa cumpar aftermarket de la producatorul care le face si pe cele vandute drept OE.

I had this bike before to buy my multistrada, in version ABS with fitted full system Akrapovic, amazing bike, strongly advise in changing the exhaust at least with a slip on, it feels much better and lighter, the original can is huge and heavy.

I have a JVC android tv but it supports 2.4ghz only. Can i use this to connect to 5ghz channel?

I reset to 0 in adaptation, but dpf light on dash comes back on after 10km drive, whats wrong? No fault codes in engine control module

I know op-com has a lot of functions besides diagnostics but is it possible to program from ECU for example EGR? I don't mean emulation just disabling the egr controller after plugging the swirl flaps from the intake manifold and unplugging the swirl flap open/close control lever. The patient is a zafira b 1.6 105hp petrol

Where to get the replacement part with the cables at 5:07? Thank you!

Multumesc de ajutor super util filmuletul!❤❤ Un mare Like!!!

Does anyone know if u can remove pads and just run no back breaks

Gran bel lavoro amico. Uno di questi giorni lo faccio 👍

Te rog. Zi mi și mie la 1.6mpi O2 Fl. Unde este senz ax came? Se oprește un mers și da eroare p1348... Ma poți ajuta cu o idee.? Mersi

After 7 months after install, the Continental belt started squealing due to a bad (Continental) tensioner. I discovered that, when you first align the tensioner, you first need to tension it all the way to the maximum tension that you can 5 TIMES, to prevent misalignment between the belt and the roller. And only then you can center the arrow! My belt started rubbing against the roller after 7 months. Be careful to do this extra step. I will order a SKF tensioner among with a Gates timing belt. Also you didn't replace the screw where you mount the tensioner, this is a frequent cause of breaking. And you also didn't replace the 4 crankshaft bolts. I followed your tutorial but with some extra steps, and still i didn't have any luck. Spor la treaba!!

Where did you buy this LED bulb? What's it like?

I found it easier to fill using the gearbox breather pipe take the cap off & use a funnel

Se poate repara o volantă cu masă dublă

How do i get one

Can anybody tell me the Password for the File?

Grazie del video utile !

Great video! Quick question, i also have the 2.0 model. What stops the drive shaft from coming out? There doesn’t appear to be a retaining clip or bracket on this 2.0 litre model. Thanks.

How long did it took to be done?

I love the part where you showed us how to remove the bumper

Salut ! Noaptea se vedea bine ?

Salut, cum ai facut gaurile alea jos langa proiectoare? Ai cumva un tutorial si pentru acelea?

hi, what is the name of the program?

Felicitari pentru lucrarea! arata super bine. Imi puteti spune va rog ce dimensiuni este teava intermediara? iar cum ati prins ferestrele daca nu va suparati? Am o structura de fier si as vrea s-o inchid tot cu panouri sandwich

Nice rims, what's a model?

Купил адаптер, нл моц ТВ не видет эго😢

Hello. Can you deactivate the blown lamp warning in the check control and install LED lamps? How would it be programmed? It is a 2010 Astra J. Thank you so much

channel not available

salut. stalpii ce dimensiuni au?

Salut frate, am golf 5 4 motion, cand si cand in mers im aprinde esp si dezactiveaza tractiunea pe spate, dupa ce opresc masina si o pornesc din nou tot normal. Poti stia ce e cazu?

No vid ahows a stuck ball joint in the knuckle

Salut. Pozitia fuliei de la vibrochen este una anume? Mi-a curs ulei pe la semering , l-am schimbat ,motorul mergea perfect echilibrat...a curs ulei si cu al doilea semering... l-am schimbat din nou ..nu mai curge dar motorul vibreaza....fulia este stransa ...cureaua pusa cum trebuie....nu stiu....

Engine is off there will be more wobble without oil presure. But you probably killed it by that screwdriver

Very good

Buna ziua! Detin un Op-com cu versiune 1.67 si ce ati facut Dvs. in clip am reusit si eu, insa exista o optiune sa schimb meniul ECO din BC cu unul numit Performance, unde ar fi si alte optiuni, insa nu-l gasesc in software niciunde. Multumesc pentru orice ajutor. O zi buna!

rims model?

I change it new injector for my car, but it is has little black smoke now please? What do you think? My car Vauxhall Astra 1.7 /2012

you show absolutely nothing

Hello. How did you tighten the pressure plate? With special tools or not. I have exactly the same one. Thanks.

I’ve got a Vauxhall Astra van and mine is sounding the same where is the suction control valve on it

Salut,scuzați deranj acum ceva timp ati postat niste clip uri cu un opel astra j vin cu urmatoarea intrebare eu a trebuit sa schimb kit ul de ambreiaj + volanta am pus Valeo pentru ca luk era cu 2000 lei mai scump în condiții normale de condus ma va tine 2 ani undeva la 20k km pe an ?unii oameni se plangeau de Valeo alții spun ca a tinut si 200k km dvs ce parere aveti?

can clean with wd 40

Thank you. Just need vcds now or finding someone with it.

Vă salut !! Smart cam CL+ DIGI se potrivește la toate smarturile ?

Salut poți să îmi spui unde se afla siguranța pentru faza lunga?

След свалянето на този датчик трябва да се обучение