What size bolt for removing clutch?

Great and helpful video. Would be a bonus to have you walk through the uninstall process as that is hard to follow but I figured it out!

How long do springs last on a van? Or do they even go bad? Thanks

Thanks for your video. Make sure to have the car off the jack stands and on a level surface when checking the oil level.

What happened to the oil pan gasket?

I really like the design. Wish I had you guys here to build me one of those for the John Deere. That's some cool madmax stuff right there and some really good welding. Look very durable and that was a cool video.

What I used was a 3 1/2" ratchet extension (3/8" drive). Worked awesome with the bolt.

My guy

In order for it to seal on the outside it would need to be flat at least in the immediate area where the hole is. That means all of the raised areas would need to be sanded off and down flat. It is nice to know about the heating helping.

Hey.... as long as it's there, right? 🤷

I subscribed because of a comment asking about the second thermostat and you responded with a perfect answer. I can't wait to do this project myself. god bless you guys for your thorough video and perfect response. i was confused because i planned on replacing both thermostats because I'm not sure which one is the problem and found out where they are I'll be back once the pieces come in for my 20th time watching the video😂 i love learning about cars and people like you guys make it so much easier to learn

I watched this whole video was kinda hoping you'd ride it but no that was a waste of time

Mike: “What’s the hold up?” Chris: “traffic” 😂

Flex pipe really tested my welding skills I learned in high school back in 09😂😂😂 what a pain in the ass Nothing like laying under a vehicle welding. New respect for Mechanics

Yo bro, where did you point the jack stand to lift it up? I thought I can only place the jacks on the sides when lifting the front

You lucked out that the oil filter was that loose. I know that there is no reason to reef on an oil filter when putting it on, but the oil filters on all of my equipment seem to need a bit of coaxing with a wrench of some kind. Cheers!

Thank you !

Nice video ! Do you know who sells longer shocks and longer front struts so I can raise my Toyota Sienna and put on off road type tires on other than putting on front and rear spacers. Thanks !

some soap and water wouldve went a long way

Thanks for the video. Very helpful. I have AWD and my support arm did not drop down far enough. Had to use a spring compression tool to get them in.

*Promo SM*

Thx

Very well done,best video I've seen. Espically for people like myself who needs to go step by step slowly. THANK YOU VERY MUCH.

What's the size of cartridge remover

Why are these new springs r being installed upside down compared to the ones that came out ? The flat end is up on old ones, but down on new ones

What did you charge for this job?

When unscrewing the oil filter, in addition to wearing latex gloves, i like to use a shop towel to wrap around the filter while loosening it. Helps to avoid spilling dirty oil on my arm.

Have bought 4 of these starters and had abysmal life from them. After a few dozen starts, the solenoid contacts burned out and I get the dreaded “click” “click” “click” for as long as I want to try cranking it😢 I still have all 4 and have purchased replacement solenoids for them that are supposed to be high quality. Haven’t got any tractors to use them on though. Owners had enough of those type and bought new direct drive Delco in one case $$$$ and a planetary gear reduction type in the other. It has been a few years so hope you have better success.

What size is your flexi compared to the exhaust? Can see it slips over the original exhaust

Is the knocking engine a problem? I have too this trailboss and its knocking tooo...its scarry me...its a rod in scrap or its a wariator knocking only?😢

Just curious , how on earth did those springs break like that ? Perhaps too much weight on the end of the vehicle , too high a tongue weight ?

Wondering .... what is the "part number" for the "Flex Pipe"? I need to do the same repair on the exact same vehicle. Thanks

This vehicle has 2 thermostat isn't it?

replace the crushable metal washer on the oil bolt ?

Awesome video. No flashy, loud music. Very steady video. Concise instructions with nothing missing.

Good to know:) thanks. I've read on other forums it works on tractor tires if you install from the inside.

Hi, I have a similar tractor with a starting problem. Can you tell me the kind the issue I would have if this part is bad? What exactly does this relay do? When I try to start my 3020 I mainly get clicking which I assume is a solenoid issue. What issue(s) were you experiencing that led to replacing this part and eventually the starter?

🫡🫡🫡🫡🤐🤲🌧️🌧️🌧️🌧️🌨️🌨️🌨️🌨️🤲

Will this work on a 4020??

And I thought my weld job was bad.

احسنكم من تعلم علما و علمه

Great video. Thanks for the content

would that be the problem on my trailblazer 330 because it goes then it boggs down and turns off put a new carburetor and still does it

Buen trabajo amigo👍

one of the better demonstrations I've seen. Thank you. What is the lb-force settings on the impact driver for the wheel lug nuts? What about the lb-force on the lower mount nut on the shocks?

Sir, does this machine run?

Buenas noche que tipo de soldadura se usa

Starter a piece of China crap, period. Find someone that has quality stuff not turds

I didn't know this was a thing is this every year

Does it leak gas from the carb overflow at all? I heard it is normal due to excessive amounts vibration that it makes. Annoying