i know this video is old, but i realized my problem about the registration marks is the fact… in the studio, the marks were inverted and my marks on paper were default… so… i had to hit the “default” on studio and it can read(i’m still new to this LOOOL)

You have adjust the registration marks in the studio outward to compensate for the machine error. Try setting the studio registration marks inward, but print the job with the registration mark further out, it should fix the problem.

did you fixed this issue already?

So, did you find out how to fix it?

My machine was cutting kinda ok. The thing is, sometimes it cuts really well but only the stickers at the top of the sheet, and the ones at the bottom not so good. And now it won't read the registration marks. At all..

Line the blade up with the registration mark and it will work. It took me years to figure this out 😭😂

Why always i got failed registration mark. Urghh 😢

Are still using that? What is the situation?

Help, do those cables sometimes get bent back down under there. My throttle is stiff due to my boat sucking a wakeboard rope got sucked under. I think the rope pulled the cable rod or bent the rod to the bucket.

I changed the blade & everything was fine

I know this might be a bit late, i keep having this issue but i found the solution. 1. Move your print near to the edge of the mat, maybe about 5cm below than the grid. Make the registration mark thicker and use inverted mark. Bottom of your artwork must be facing to the printer and must be place to the right side. 2. If still not working, as usual use manual registration. Required a few trial and error, hope that helps

Thank you!

Was this issue ever resolved with silhouette??? I just got a cameo 5 and am wondering if I’ll run into the same issues.

Was this issue ever resolved with silhouette??? I just got a cameo 5 and am wondering if I’ll run into the same issues.

THANK YOU

Why are you using electrical tape on the wheel at the end?

Can you just use masking tape on tires, then on rims, then paint the outside of rims??

You are seriously awesome. I have been fighting this issue and you have saved me from throwing my auto blade at the wall 😂

Literally my whole night... I despise this product!!!

I've been trying to knock the cable assembly free into the bilge and nothing has worked. Has anyone else really struggled with this? I removed the washer and bolt on the transom side and removed all visible silicone on both the transom and bilge side with no luck. I even heated the threaded bolt to try and loosen anything that could be in the passthrough.

Nice work. Maybe directly wheels can paint to gunmetal color.

put your desk lamp on the opposite of your video.. it works

What if you were to do white electrical tape instead for a white outline?

Nice

Thank you for showing how to do manual! I was about to be so over this machine and Print and Cut!

This is why I hate these cutters, they beat their own purpose of saving our time manually cutting the stickers.

how have they held up ? What brand spray did you use? How many cans would you recommend?

Amazing! Does it wake your desktop up from sleep? Also wondering if there would be a display on your monitor as well as the device that it's connecting to

kzbin.info/www/bejne/enWXmKVqa5yBpJI&ab_channel=LadyPrintBoss

Solve the problem by pulling the upper and lower cover

Pull the top cover out and the problem is solved

Its 2024 and im having the same issue also its cutting not in the shape i wanted 🥺

Thank you. Just turning on the lights in the room fixed it for me.

For everyone still wondering, do not let the mat hang, make it so it at the same level as the sensor and it will work. But a book under the mat to keep it at the same height.

Good thing it was fixed and passed inspection by Nick

Wind can really mess things up

I FIGURED IT OUT!!! It's a software issue, and not necessarily a bug, but a feature! If you're in any other cut mode besides "SIMPLE", take note of the different layers you have selected. For example, I was in the "FILL" feature of the cut dialog box, because I wanted only the object WITHOUT a fill to cut, everything else was a graphic. In selecting that, there are options for each fill/line/layer which are: tool, weld, fill color, material, action, and carriage. THIS is where you want to select your cut settings! Previously I was in the vinyl sticker settings, so the machine would revert to this every time. This allows you to cut various materials AND cuts in one job without having to re-register the artwork. I hope this helps! No need to remove your cartridge and manually adjust!

I printed out another set of registration on a sticker and stick it without lamination. This solved my mine guys. Maybe the surface was too shiny? The one that failed on me was laminated with gloss. Hope this will help you too guys

you can just set the to manual blade so the software does not click the blade before starting a job

Thank you for this video!! This was a lifesaver!

I had to put scotch tape over the first box. I guess it wasn't Shiney enough?????

Thank you so much I am trying this right now. I have sticker orders to ship out and I would be so crushed if my machine just isn't useful for me anymore.

Hello, why my auto blade stays in 0? When i make it manually 5 it go back to 0 when cutting

also it not having a lamp??? "Reasons for registration marks reading failure: 1. missing light source" my question dear silhouette is: why is there no light source on your machine that needs a light source to work properly?

I'm guessing this is how Tesla painted the hubcaps from factory, explains why the silver part has so much black overspray.

In the video, you do not have the Cameo Cutting Mat selected. You need to do that to get the registration to work. Design Tab > Item 3 (Cutting Mat)

Why does my stutter or shake at once place I even put a thicker mateirsl

What was the initial problem you were having that prompted you to do this repair or even to look for an issue? The reason I found your video is I’m looking for a solution to my problem which is… I have a twin engine Yamaha, 242 Limited. When I take left-hand turns, the turning is great. Nice tight, high bank turns. But when I turn to the right, out of the blue this past Sunday, I stopped having the ability to make high banking turns to the right. It’s more of a long swooping turn. For example, if I were to do a full circle with a left turn, that circle would be much smaller in circumference than if I did a full circle with a right hand turn. Wondering what the issue could be.

Thanks for the video. I just did the same thing, replaced the cable. I am having a problem. I have the linkage adjusted out as far as it will go and It doesn't turn left very much. Like, it doesn't extend far enough out of the transom to turn it very far left. Any suggestions on that? I thought about trying to get an extender, but then it may not turn right as it should. I have adjust the linkage on both ends every way that it can be. I have searched for hours on it and can't seem to find out much information about it. Along with this, the steering wheel is way off center. When I try to center it, the cable doesn't reach out far enough to connect. I can't figure it out. Any advice would be appreciated. Thanks