Mind if I use this video for an intro?

Hello! What is the name of that equipment what you use to detect the leaking? Thanks!

Git some questions: 1) So you have no air bubbles because of the clear coat that is actually "makes the surface"? 2) Why do you use PVA if you already applied the wax? 3) Did you wait for clear coat to fully cure or get tacky? If tacky then why did you use airtack spray?

für welchen Sitz ist das die Schale?

Do you need this regulator when using the MTI hose?

Why did you use peel ply? You can use perforated film its easy to remove and you can save your money.

Wie heisst der Song ab 3:21? Wo kann man ihn beziehen falls selbst komponiert? Vielen Dank, tolle Produkte übrigens :-)

why did u place the MIT hose around the part?..is that to catch up the rest of the resin?..cause i didnt see the resin come out from any of the sides or corners exept the middle

Hello, I can't tell you the different of each part, but it saved about 50kg.

What is the weight of the different parts of the body please ?

I am loving this MTI hose! I will definitely start using it with resin infusion. 10:06 better not use a metal screwdriver on the tool.

I AM FROM INDIA

hi sir I need to have mti hose for infusion process can you send me the sample for r&D PURPOSE

Actually perforated film is unnecessary and you can save money and weight with using core material.

never thought of using my spray glue through the whole process. hmm.

what is the adhesive that you are spraying?

Hi, no, there is no need for a resin catch pot when using the MTI hose. The MTI hose is resin impermeable so that no resin can travel to you pump. You have to make sure that the ends are sealed so that no resin can get into the MTI hose.

Auch hier, vielen Dank!!!

Huge, thanks, this is very helpful!!!

Thanks a lot!

Es sollte erst gar kein überschüssiges Harz eingeleitet werden. Dadurch kann man mit Hilfe der MTI Leitung Harz sparen. Gegen Ende der Infusion kann man den Harzbehälter ca 1-1,5m tiefer stellen als die Form, so verhindert man über das so erzeugte Druckgefälle eine Übersättigung des Bauteils. So kann man reproduzierbar VF von ca 55% erreichen und gleichzeitig Harz sparen.

You have to model it to your plug. I have done that by flexible sheets and wax.

Its Gema free music, I do not know the tracks. Sorry

The MTI hose is resin inpermeable, so you can not take out any resin. But there is no need to take the resin out. Just infuse as much resin as you need and than close the resin feed. That also helps you to lower your resin waste. An easy way to get a good VF is to place the resin pot to the end of infusion about 1.5m deeper as the part. Therby you create a pressure difference wich helps you not to infuse too much resin. By this way you should get a VF of about 55%.

I know it's off topic, but can I ask you what is the music under the video?

Very nice! What I can not see is where the surplus resin is taken out in order to achieve a (nearly) perfect resin to fiber ratio. Second question, what is the rate you achieve with regard to resin-fiber with carbon or glas?

Nettes Vid. Unklar bleibt, wo das überschüssige Harz abgesaugt wird, damit ein "gutes" Faser-Harz-Verhältnis erreicht wird!

I am interested in your product however I went to the site and clicked the translate button from German to English, and it only had the information describing the hose. I would like more information like the cost of the hose. the video shows that it can be used similarly to resin infusion with one less step, please send me some links for the total set up process. Thank you,

Is the finished weight of parts close to identical? I am looking into a large scale RC plane project and love the idea of a carbon fiber clear warplane.

Hello, I leave the part under vacuum until it is cured complete. The clearcoat is the HP-Textiles In Mould Coating, it should cure over night before you can go on. hats much easier than to go on with the further layup.

Did you leave the part under full vacuum while it cured? What was the clear coating you applied ? Did you let it cure overnight? Or did you layup immediately? Thanks Fred

What do you mean? There is no plastic it is glued on, and wich other side? And what do you want to do with a compression chamber? May be that you did not rate the correct video?

We have the adhesive here in India can you tell me if it is a temporary adhesive for fixing purpose or permanent adhesive, what is the tackiness you are looking for.

That's not a hole, thats a piece of PVA ;-) But you are right, it looks like a hole ore a surface problem.

stop het beeld even op 10:58 daar zie ik toch echt een gat... nee mar goed het ziet er netjes uit

where can I buy MTI hose in Canada?

wow. beautiful and sexy. love it.

No, it is a spray adhesive from MW Werkstattprodukte. The most important thing is to lay down the fabrics very accurate.

Is it a special spray adhesive? I am about to begin a project on a similarly odd-shaped part and want to make sure every corner is molded.

3500 views and no comments? This is sick!

@qwertzuiopy123: Hallo, das Vakuum sollte ca 20mbar absolut betragen. Hierzu benötigt man eine Vakuumpumpe die auch das erforderliche Vakuum erzeugt. Ebenso muss die Form absolut dicht sein!

thank you!

@atmospherejo It is a normal spray adhesive, I use the product from MW Werstattprodukte, alternativ Airtak or Aerofix.

can u please tell me about the adhessive u use is it a normal adhessive or what is it and what material it consists of or the brand too.

@MTIinfo That is awesome sir, i will contact you in a few, i will set up a place to experiment first. I really like this and i wanne give this a go. I hope i can get a good mould build, this will be tricky. Greetings

@zomaardan You can buy the hose for example at HP-Textiles or if you need great quantities you can contact DD-Compound direct. If you contact us via mail we will send a sample.

Awesome to watch a pro at work, how to obtain this type of hose?

@MTIinfo very interesting! :)

@rippedanny In the classic vacuum infusion you use for example a spiral tube as evacuation hose. We use the MTI hose, a special membrane tube. It is air permeable and resin inpermeable. So you only evacuate the air from the mould and no resin. You can work with a maximum vakuum the hole time. When the part is complete impregnated the resin stops at the MTI hose and the full ambient pressure is working on the part because it is a closed system.

@rippedanny : If you use a spiral tube you have an open system because resin can get out of the mould through the evacuation hose. So airbubbles in the laminate can expand and press resin out. Using the MTI hose this is not possible and you get air bubble fre laminate. It is also guarartied that the resin impregnates the hole part.