Good Enuff Customs

Пікірлер

@calvinswindle9432 2 күн бұрын

Looks awesome

@goodenuffcustoms 2 күн бұрын

Turned out pretty good, now I just gotta paint the hood and roof…

@southern_il_s10_sportscards 3 күн бұрын

Nice

@goodenuffcustoms 2 күн бұрын

Thanks!

@shanes_bs2659 3 күн бұрын

That thumbnail is gold! 😅

@goodenuffcustoms 3 күн бұрын

I was laughing the whole time I was making that one!

@SIMPLE.C10 4 күн бұрын

Sweet video

@goodenuffcustoms 3 күн бұрын

Thanks!

@yeap82506 5 күн бұрын

I appreciate this series. I have a 87 I’m doing front floors and rockers on right now. Already did the tail pan, tailgate posts, and rear floor. I had problems as well with the AMD rear section of the front floor. I had to cut the notch at that point where the patch panel met the vertical cab structure. No other way I tried to fit it together would allow the weatherstrip channel to come close to the rocker panel. Just part of the process I guess!

@goodenuffcustoms 3 күн бұрын

Yeah those panels are a bit of a pain! Good luck on your truck!

@southern_il_s10_sportscards 6 күн бұрын

Man I was trying to make it without the truck but nothing went my way. Hopefully I'll be back next year. Good video 👍 and trucks look good

@goodenuffcustoms 6 күн бұрын

Thanks! I was looking for you just to see that sweet s10!

@southern_il_s10_sportscards 6 күн бұрын

@@goodenuffcustoms hopefully bring it back for 2025 👍

@Hillbillygarage1215 7 күн бұрын

Next lap job, try 6 to 7 inches of 1/4 inch fuel line/vac hose. Slide over the valve stem (valve in the guide) might need a small clamp. A couple inches of 1/4-20 all thread in the other end and chuck it up in your drill. Wet your finger with oil to put pressure on the bottom of the valve. Pretty slick, high speed lapping. Bounce the valve off the seat every few seconds.

@goodenuffcustoms 3 күн бұрын

Great tip!

@Hillbillygarage1215 7 күн бұрын

Goodness man, 25 minutes till the first cut. Love what you're doing but mercy pick up the pace. SMH

@goodenuffcustoms 7 күн бұрын

Yeah, I get a little chatty. That is something I’ve been working on!

@Hillbillygarage1215 7 күн бұрын

@goodenuffcustoms good stuff though, is there a follow up video on the heads/engine build?

@goodenuffcustoms 7 күн бұрын

There should be a couple more where the engine is assembled. I haven’t dropped it in anything just yet to run it. I should be getting to that in the next month or two

@shanes_bs2659 9 күн бұрын

Dang!

@goodenuffcustoms 9 күн бұрын

Joe Dirt said it best!

@simosimpson5189 9 күн бұрын

Nice Show. Thanks for sharing. Looks like it was hot that weekend.

@goodenuffcustoms 9 күн бұрын

It was a little warm!

@calvinswindle9432 9 күн бұрын

Awesome trucks!! I would love to bring mine if I ever get it finished

@goodenuffcustoms 9 күн бұрын

It doesn’t have to be finished to bring it out and show off what you got!

@kenh.7022 15 күн бұрын

Clean the aluminum from your burr with muriatic acid. It eats the aluminum up in no time.

@goodenuffcustoms 15 күн бұрын

Didn't think of that, definitely will give that a shot.

@calvinswindle9432 16 күн бұрын

Steve is looking awesome!! Keep them videos coming!

@goodenuffcustoms 15 күн бұрын

Thanks and will do!

@mechanicmike1236 16 күн бұрын

Both trucks look great! Have a great time at the show!

@goodenuffcustoms 15 күн бұрын

Thanks, I’m sure it’ll be a good time had by all!

@jonpaulison2283 16 күн бұрын

Steve looks great

@goodenuffcustoms 16 күн бұрын

Steve’s a sexy beast!

@Jsaul32 24 күн бұрын

Looks like the trick is keep plenty of clear on the applicator. I've tried it on a couple spots on a few trucks but it always came out streaky for me. Might need to go a little heavier the next attempt.

@goodenuffcustoms 23 күн бұрын

The trick appears to be getting the applicator wet but not too wet. The flat surfaces aren’t too bad, but the sides are a different story.

@matthewkruckenberg4137 24 күн бұрын

Could have done Steve first then do Big John

@goodenuffcustoms 24 күн бұрын

The priority was Big John, Steve can wait till I get to Little John once it cools down a little.

@damonlawson2117 24 күн бұрын

The obs Chevy truck is bad ass I have a 95 ext cab and a 90’ single cab and had a 93’ 94’ I’m looking at a 89’ 5speed dully 2wd 454

@goodenuffcustoms 24 күн бұрын

Thanks! Careful with the dualies, they are addictive!

@calvinswindle9432 27 күн бұрын

Sounds great

@goodenuffcustoms 27 күн бұрын

Thanks! It turned out way better than I expected.

@user-iu7ls8tr9d 29 күн бұрын

It sounded really good on my end man very nice truck by the way

@goodenuffcustoms 28 күн бұрын

Thanks! I’m really digging the new daily!

@simosimpson5189 Ай бұрын

That truck is the boss !