Пікірлер
@digishinegrow 2 күн бұрын
I’ve been following your content, and I’m really impressed with what you’ve built! You put a lot of effort into your videos. I noticed a couple of small SEO tweaks-like optimizing titles and refining thumbnail styles-that could help you attract even more viewers. Would you be open to hearing a few quick tips? Best, Shahin
@LetsgoHOVA843 3 күн бұрын
Good video bro no talking straight to the point
@roundspokeez 7 күн бұрын
You dont switch on while connect to the battery..😅
@PaintdropArrow 11 күн бұрын
Here's to fixing our own vehicles! I thank Jesus for you & this video... as it has been a while since having to do this repair.
@matthewhernandez2213 19 күн бұрын
If your steering wheel shakes while breaking 99% of the time it's either the inner or the outer tie rod ends but its always best to replace both at the same time.
@RadikalPolitik 29 күн бұрын
Warning! Laptops dont use chargers. They use adapters! Charging circuit is inside the laptop! Also most power tool batteries dont have bms that protect the cells so never do this unless your life depends on it! The battery doctor
@andrebrown4822 Ай бұрын
Your right 👍🇯🇲
@MichaelDeaton-n3g Ай бұрын
What if my laptop charger doesn't have red black and white? I have white, wrapped in bare wire wrapped in white again and then bare wire around that.
@GnarledSage 2 ай бұрын
Why do you put black and white together? Will it work if that’s not done?
@fixwhat1137 2 ай бұрын
Hi GnarledSage, the black and white wires are the ground and neutral wires. In electrical circuits, the neutral wire carries the current, and the ground wire is there just in case there is a short or fault in the circuit. Yes you can use just one of the wires. If I remember correctly, I believe its the white wire that you can use by itself. Instead of one of the wires hanging around and not connected to anything, I just connected both of the wires. Thank you for the question.
@GnarledSage 2 ай бұрын
@@fixwhat1137Thanks for taking the time to explain.
@fixwhat1137 2 ай бұрын
@@GnarledSage You are very welcome
@Famillechretienne12 3 ай бұрын
I have a 2010 Subaru Forester, and the dashboard is displaying the same warning lights as yours. I’m going to try doing an oil change since it’s been 3 months since my last one.
@crutchgecko 3 ай бұрын
Just had a lot of pitted rust on relatively new rotors (1 year old) but the car was not used much and the rain had caused a lot of rust especially where the brake pads were touching. Just lost my job, have 4 kids... Sanded and sanded by hand like this but finally used a disk with velcro attachment. 80 grit. Went through 10 sheets easily (they clog up pretty fast) was careful to try to sand everything evenly. In the end the results were good, however, in hindsight it was barely worth it. Read rotors cost $40 canadian each, front vented rotors probably under $80. I saved money but now i have rust dust all over the driveway, probably burnt 1 years worth of brush life from my electic drill. The sanding disks weren't free, the velcro is now peeling off the sanding disk holder, and my back hurts from sanding for hours. (At least 20-30 min per rotor I would say). As I was doing it all i could say in my defense is that "its good for the environment not to throw out these mostly working rotors" other than that i had some pride that I "did it myself" but thats about it. Not worth it, your brakes will be perfect with nice new rotors. And i agree, if your rotors are warped, its not even going to fix the problem!
@zino6661 Ай бұрын
I went through the same as you. My car is almost brand new and new rotor, but sat on my driveway for long time without being driven. The rotor developed embedded rust. I tried with sanding machine with 36 grit and then 80 , 120 but still feel the rough surface. $100 for OEM rotor each.
@halfdeadedlifereturningwit3420 3 ай бұрын
2014 Crosstrek same problem, same cure. The lights went out as soon as I left the quicklube. Thank You.
@ericnuchols270 4 ай бұрын
Sand all you want.. If that rotor is warped your just wasting time.
@Jen_Is_Outside 4 ай бұрын
What if this happened AFTER an oil change and oil pan gasket replacement? I'm still slowly dripping oil from the bottom (silver dollar size over night) and my oil was low 1 quart after 1300 miles. They diagnosed and fixed a leaky oil pan gasket, but that def wasn't the problem. Then BAM two days later these lights. It didn't throw a code at two shops. And the lights will randomly go off for a few days. I'm thinking oil sensor? Help! 2008 Sub Outback 136,xxxx Thank you for your channel!
@elijah-jarvis-gill3365 4 ай бұрын
Dude your a life saver I was just about to give up on my 94 but you just saved it thank you
@timeforbigchange9417 4 ай бұрын
Thank yuio I must get rid of this stupoid unneccearay design dont care about spell check , stupid 20212 forestee, old TOYOTA S ismwhere itds at ,
@ttinnovations3310 4 ай бұрын
just put them back on the car, put the lug nuts with a spacer, and used a angle grinder with 80 grit, put the car on drive, and skim the rotor ...
@J9227 5 ай бұрын
I’m having the issue on my 97 Acura RL the parking lights staying on with no dash illumination but I Regain the dash when I pull small relay to turn parking lights off . Any help ? My alternator recently went out and the car started being silly .
@danielsumerix4419 5 ай бұрын
Well done video 🙏
@jurisdavison4625 5 ай бұрын
Thank you my guy I appreciate it
@joserivera-vs7kw 5 ай бұрын
To fast
@ronparker645 6 ай бұрын
Awesome
@BabyGangsterIsMe 6 ай бұрын
dont waste time to resurface the rotors... just go to toyota and buy rotors from them, it is expensive but it last you more than 7 years and no rusty at all .. u save a lot of time ... dont buy cheap rotors bc it lasts only 3 years and u have to resurface it again and again .. wasting time bro ... for parts, buy orginal one and it will last u a long time... i hate after market parts... it sucks
@lisiatepalu7737 6 ай бұрын
Thankyou for the help Thankyou
@thegoblin622 6 ай бұрын
So for this code it’s the sensor before the cat ? Bank 1 sensor 1? And is it the down stream or upstream?
@alexvieira7945 19 күн бұрын
Up
@jacobkeiffer8768 6 ай бұрын
Not helpful at all. Doesn’t say what Acura this is, could be a mdx could be a rdx or a TL who knows. Also I can barely hear a thing your saying to much background noise.
@Doyen_ 6 ай бұрын
Please can you use an 18.5v laptop charger to charge a 20v battery.
@daytekone 6 ай бұрын
No you need more voltage to charge.. and amp will determine speed as long as the battery supports it. thats why car alternator charges at 14.8V to charge the 12v Battery
@-mejor-que-nostradamus-6152 2 ай бұрын
Yes You Can.
@Doyen_ 2 ай бұрын
@@-mejor-que-nostradamus-6152 thanks 😊
@Doyen_ 2 ай бұрын
@@daytekone alright 👍
@billbillington4885 11 сағат бұрын
You can charge it at 18.5 but it won't run for very long nominal voltage to charge in 19 volt battery is around 20 volts That's why you have other brands that say 20 volt max It's just an 18 volt battery pack that's nominally charged to 20 volts
@stephenwen3544 7 ай бұрын
Quick question, does this mean if i replaced the distributor rotor ONLY, i wouldn't have to use a timing light or have the engine on top dead center before starting it?
@MrRasZee 4 ай бұрын
put engine on TDC and mark timing just to be sure take no chances
@fistrike-v6u 7 ай бұрын
Can 19v laptop charger be used to charge 18v
@-mejor-que-nostradamus-6152 2 ай бұрын
Yes
@kylecallis77 7 ай бұрын
Vibrating sander might do better
@LPenn0505 7 ай бұрын
Thank you. This helps a lot.
@fixwhat1137 7 ай бұрын
I'm glad to hear that this helped you. Thank you for watching.
@jesuscamacho790 7 ай бұрын
What year is the car?
@RVMD95 8 ай бұрын
Don’t do this. Buy new for the safety of us all!
@charomivida 8 ай бұрын
Dude , I have turned down thousands of rotors with the right equipment. They are ALL WARPED , just buy a new rotor every time, because you can't machine them any more like I use to do, the metal is Junk they are not cast iron so can't be machined
@schemeteam2954 7 ай бұрын
You're right about that but sometimes ppl don't have money to buy new ones so they gotta figure out other methods to what they have.
@leonardoagriel6207 8 ай бұрын
Very good thank you
@michaelanderson9237 8 ай бұрын
You can’t😅 fix stupid!
@1234567890CAB 8 ай бұрын
Where I live, the back of the rotor always gets rusty and grooved. What I like to do is take them off and slide the rotors flat against the asphalt road, turning them frequently. After about 15 minutes, the back will be completely resurfaced.
@BabyGangsterIsMe 6 ай бұрын
if you buy expensive rotors, it wont happen ... go to toyota and buy it ... i used to buy cheap rotors and wasted my time to replace it every 3 years or resurface ..wasting a lot of time.. if u go with expensive rotors, u dont need to worry about rusty
@Freedom_Rider915 8 ай бұрын
You will never solve the problem of a warped rotor by doing this. Have them turned or buy new ones.
@IsaacAkpan-ld5ey 8 ай бұрын
Timing
@sabiya2 8 ай бұрын
Nice video straight to the point, But I have a question, I have the charger for my cordless battery(which doesn’t work) can I hook up the laptop charger to the original charger? ie take motherboard out and just hook up positive and negative wires, then just slide battery on the original charging dock? Keep the oem charger just being powered up by the laptop charger?
@fixwhat1137 8 ай бұрын
Hello sabiya2, I appreciate it thank you. I'm glad that you enjoyed the video. To answer your question though, I'm not sure. What if your charger is the issue, the internals of your charger such as the circuit board inside. If you power the charger but the internals are broken, it still may not charge your battery. That is just my opinion. You do have an interesting idea though.
@fixwhat1137 8 ай бұрын
Hello sabiya2, just a quick update, I might have misunderstood your question, if you meant to remove the circuit board inside the charger and connect the laptop charger to the leads of the charger directly bypassing the circuit board inside the charger, then that might work. The downside is that you will probably be able to charge only one type of battery. You can only charge batteries that can fit in that charger. But still, what a great idea.
@sabiya2 8 ай бұрын
Hi thanks for your reply, ok so an update, what I did was I connected the laptop charger directly to the pins on the inside of the original cordless charger, so now I just slide the battery into the charger and it works with no issues. Thanks man
@fixwhat1137 8 ай бұрын
@@sabiya2 I'm glad that everything worked out! Thanks for the great idea
@n3alsnail299 7 ай бұрын
@@sabiya2simplest thing I've see yet
@barenekid9695 9 ай бұрын
IF your steering wheel Shakes!! your car is DAMAGED get it to a shop.. yesterday! Rotor warp is felt as a slight pulsing of the brake pedal during heavy braking.
@joaomoguel4086 9 ай бұрын
You are a genius
@humbertohuizar1375 9 ай бұрын
Thank you for the info
@fixwhat1137 9 ай бұрын
You're welcome! I'm glad it helped
@Natives-cm8yb 10 ай бұрын
This video is awesome, Im having some idle issues so I took mine apart and after taking out the purple solenoid, I noticed mine does not have a spring or a spindle. It looks like it broke off. Hopefully this is the culprit of my issues 🎉! Thank you!!
@fixwhat1137 10 ай бұрын
Thank you for watching! I'm glad that this helped you!
@jeffbilbrough6494 11 ай бұрын
If you're getting vibration when you brake due to warped rotors, this idea will do nothing for you. Warped rotors are dangerous & should be replaced, the cost is irrelevant, your life depends on them!
@chevyhighrider 10 ай бұрын
Often times “warped rotors” are not actually warping at all. Rather it’s uneven pad deposits on the rotors.
@alfonz0010 6 ай бұрын
Do you actually work on this stuff or do you sell parts. Sounds like you sell parts.
@jeffbilbrough6494 6 ай бұрын
I don't sell parts or anything like that. I just know that poor / defective brakes are dangerous, I mean, it's only your life that depends on them working properly isn't it!
@alfonz0010 6 ай бұрын
@jeffbilbrough6494 yall got to stop spreading ignorance and stay in your lane. Chevyhighrider already explained it. Manufactures have specs to properly service rotors. I recommend you delete this comment.
@alfonz0010 6 ай бұрын
Also warped rotors are about as dangerous as a bottle of texas pete
@theredscourge 11 ай бұрын
circular strokes might be a better idea, or maybe using a palm sander in circles at a constant speed and pressure.
@fixwhat1137 11 ай бұрын
Hello theredscourge, I love the insight. I think it's great that you are trying to provide more ideas to better sand down this rotor. Trying to make things better, I love it. Thank you so much.
@jamesrichardson771 Жыл бұрын
Come on man" buy a set of rotors' that type of rotor, without bearings, don't cost that much. Think about your family, and you, riding in a Safe' and dependable situation !!! 🙏 🛠
@jamesrichardson771 4 ай бұрын
So Sorry / I guess, I just wasn't thinking of all' the reasons. 🙏
@plantedmars3079 Жыл бұрын
did u replace the gasket or rtv it
@fixwhat1137 11 ай бұрын
Hello plantedmars3079, I believe rtv does work, but I would replace the gasket. Thanks for the question.
@DARRELLGRIFFITHS Жыл бұрын
What a complete waste of time. Do everyone a favour and never ever do work on anyone’s or your vehicles ever again.
@fixwhat1137 Жыл бұрын
I would not recommend doing this on a customer's car. The rotors would either have to be cut if it can still be cut or replaced. This was more of an experiment and not an official repair. It wasn't perfect, but it did smooth out the ride a little bit.
@stretchhfab7315 Жыл бұрын
@fixwhat1137 then don't make a video. Bad repair is a bad repair.
@DARRELLGRIFFITHS 4 ай бұрын
@muttommanwith 38 years in the trade and fully qualified, yes I am.
@DARRELLGRIFFITHS 4 ай бұрын
@muttommanyour starting to sound like a Biden voter to me.
@anandadharma1933 Жыл бұрын
Excellent video. Very thorough. Thank you.