how can we run accelstepper bounce example with the tb6600?.

The part where you connect 4 pins to the GND, is that cause you want the stepper to only spin in one direction?

Hi Henry! After programming if i want to control the motor from display. How can I do it?

Hello! If anyone see this message please help me!!!! I wire my nema17 with gearbox to tb6600 ,like in video but my motor can go just in one direction,when he try to change,it can't...please help me,i also change the driver with one new ,and wire corectly pul+,dir+,ena+ at pin 2,4,6 and all pul-,dir-,ena- wire all in wagoo to create one wire and i put it in GND ,on mai board. What is the problem?pls help😅😢😢😢😢

it can be very nice of you if you can explain how you can run yours CNC with one motor ?

How do I make the stepper rotate to a certain point and then make it reverse ?

Dear Henry, can this procedure be used on the DM556 drive? My Arduino is giving me an error when I order the data to be compiled. I can't send the error, but could you help me? Thanks

What's the code for rotating the motor up to the desired angle

I am currently using arduino+cnc shield, this drives 3 stepper motors in my cnc. Do I need 3 of these TB6600 to drive 3 stepper motors?

i know i a quite old vid,but is it ok if i do 24v-1A current as input from the driver for this motor? will it affect the perf alot(will it destroy my motor?) is 24v-.5A mandatory?

for some reasons mi Nema17 vibrate instead of rotate. I don't know how to figure out

Hi Henry, I need some help, I'm a Civil Engineer and electronics is not my thing. I'm building a 40w CO2 laser and need some help with the electronics. First on the configuration of the driver: how do you determine the steps per revolution on the motor you're connecting to the driver, in your example, you set yours to 6400 steps per revolution. is that so the motor will perform at its maximum when asked by the controller/computer, or is this peramiter set according to the size of the motor? I watched another video on this subject and the guy totally lost me, any help would be greatly appreciated.

Great video, got me up and running in a few minutes. Thank you!

Is TB 6600 compatible with all NEMA 23 motor?

I have tried so many wire configs from the internet & this is the only one that worked, because, I found a 3018 controller board which has digital out just before the "on-board" stepper drivers & shorting the ENA+ to ground got it working, thanks...saves me using mach3 on my larger home made cnc, which is a headache to setup,Thanks...

why not use PWN pin insted of manually setting the pins value>?

ciao dove posso trovare i file per stamparli grazie

Very helpful. Can you provide links to buy the mounts and screws? Thanks

How come on some cnc show the signal on some cnc circuits positive 5 common and on others negative is com😢

hi

Very good tutorial. Could you tell me why the ENA+ and ENA- pins are jumpered together? I see most tutorials leave both unconnected, which I think defaults to Enabled. Also, I didn't catch what the "While" statement does, as you went over that pretty fast. Thanks!

Very useful. Thank you

Thank you very much

Thanks for the tutotial Henry, I'd been struggling with this and yours is very clear. However, mine only works if instead of connecting ENA-, ENA+, DIR+ and PUL+ to ground as you say, I instead connect them to 5V. Until then I got no movement, but with 5v it works as per the rest of your description. Do you know what the reason for this might be? I only swapped it as I'd seen on another tutorial that they used 5V, but I found the rest of their description complicated. I'd be interested in your view so I can learn more. Thanks again

my nema 17 has M3 screws, not M4

A really useful video thank you, I have a question regarding a project I am about to try and build, and that is how do you know what size stepper motor to buy for the project you are proposing to build? I want to build a unit that operates as a lift in what is commonly known as z axis so it is lifting and holding a load and lowering and still controlling that same load.

Thanks a lot. Very helpful for beginners like me. But how I will connect to power supply. I have one adaptor to use in Arduino board. Do I need to buy another adapter for controller power supply?

I am going to use 3 nema17 7.2kg torque motor is 1 lrs75 24v power enough for it?

The TB6600 Stepper Driver is garbage! Don't waste you time with this junk.

Excellent.

Hi Henry, nice sharing! Noticing you have creative opinions on DIY, not sure if any projects-building in your plan? We'd love to sponsor free prototyping services (custom CPBs/ 3D printing/ CNC machining) and achieve any cooepartion together. （PCBWay zoey)

code please

I got f2100b control and that driver with nema 17 motor

Hey dude, my cnc machine has 2 stepper motor on X axis.How to wire the second driver into the arduino uno ???

A cheap way I use as a flexible shaft coupler for steppers: A piece of silicone hose and two zip ties.

Thanks for this Henry. I'm ready to go from PWM to steppers. 🙂

can you please explain how the code achieved a full step?

This is a very well done video. Simple and clear. Thank you!

I've been buying steppers and drivers for a few years. Every item was checked ok at delivery. Now some year later a NEMA 23 and a modern TB6600 produces 15% to 30% more steps than commanded. This happens both using the test code You showed but also when using AccelStepper library. I've never faced this before. Any ideas?

hello, what is the difference between a common anode assembly and a common cathode? Will the engine run differently?

can you make a video on how you can wire the tb6600 to a ramps1.4 or mks gen l v.0 mother board for a 3d printer?

Brilliant concise video. Thanks.

Sir if we want to stop stepper,,which command is use?

Hi why I cannot turn the hand crank on a lathe after I install the stepper motor thanks Eli

Ｐ𝐫Ｏ𝕞Ｏ𝓢ｍ 😳

Creative video,thanks :)

Thank you for this video. Very clear and informative.

you have ENA+(5v) hooked up to ground in your diagram. Is that right?

If I only have a power supply rated 0.2A, 21V, will tb6600 be able to output at least 2 amps?

hello, i'm recently interested in swiss type lathes, but completely new to machining.. i only know 3d printers so far is there a reason why the headstock has 2 different movement on the same axis? why using a tilted screw for the top one?