Its a joke for BMW to use cheap plastic parts for critical functions: the chain guide, hot coolant exit connector, engine cover, etc........ . On top of this, BMW cars have poor temperature control system from bad design to unstable sensors, causing overheating which in return accelerated deterioration of these plastic parts! Shame on BMW leaders and engineers!
@AmyRobinsonValley22 күн бұрын
One important thing to keep in mind when you attempt to see if the chain is stretched while turning it over by hand… while the tension is spring loaded, it relies on engine oil pressure to properly tension the chain. So you’re not getting an accurate indication of its condition doing it that way. The tensioner will fluctuate its pressure against the chain as you rotate the engine by hand. You’re better off taking the hydraulic tension out and installing the hand tensioner screw tool, tension the chain, then retry your observation.
@spiritmusic432224 күн бұрын
Great footage killed by music drowning the narration
@chillu42029 күн бұрын
Thankyou sooooo much
@niksajazvic5066Ай бұрын
The car sounds same before and after
@ondrat97902 ай бұрын
Nice video! Where do you can get that hood on Summarit?
@robertfontaine36502 ай бұрын
I have learned how not to install OEM fcab bushings.
@kilebeeman41882 ай бұрын
Is it just me or dose this timing chain appear overly complex and labor intensive to replace. This is why i wont own a bmw but aint afraid or a night in a benz
@Shubham_Ganotra2 ай бұрын
Can anyone of you help me do this job on my 328i ? Please ? I am unable to trust anyone out there and dont have enough money to go to the dealership please ?
@frankieb22203 ай бұрын
No adding of Oil Into the Housing Prior to installing the Cap?
@frankieb22203 ай бұрын
Now Yes we are suppose to put Tad Oil Along and around the Bigger Seal..but isn't there a step missing of Oil Added to the Housing Prior to putting the Cap back on tight?Just asking..
@liljimmysfoodfactorygemstr40964 ай бұрын
How about for the high beam bulb so do I have to disassemble that frame on top to get to the covers for it you have a video for it thanks buddy
@cesar4motion4 ай бұрын
Great job, I allready see it, I have a question, at how many miles or kilometers have to changue these chains...??
@cjdonahoo10118 күн бұрын
Around 100k miles
@joshuamaina8464 ай бұрын
Where did you get your 12v charger?
@MatthewWong4 ай бұрын
Harbor Freight
@TheJoetuffguy6 ай бұрын
Who TF lays tools on their vehicle? Wish I could delete this video
@mascho227 ай бұрын
hey if you're still checking comments, did you use a 1/2" or 3/4" breaker bar for the bolt? Wondering if my 1/2" will break trying to loosen that crank bolt
@ladonnwilkerson70388 ай бұрын
When he threw the sockets on his m I cried 😢
@josueortega33628 ай бұрын
Hey man, i had a question. I have these same headlights for my 13 bmw 328i and i have a parking lamp malfunction. Any chance you know the bulb i need to change out?
@MatthewWong8 ай бұрын
Try pulling the bulb out and look at the back. I found mine corroded over time and needed a bit of sanding down to make a better connection. Otherwise it might be the bulb.
@leveragelifestyle85818 ай бұрын
Great vid. I think if you left the cap open for the fill talk while bleeding you wouldn't need to open the bleeder screws. The air comes out of the port that shoots the coolant back into the tank as it recirculates.
@adeelahmed86418 ай бұрын
How many times would you need to drain coolant to get radweld out? It's blocked my heaters
@stanponkratov2698 ай бұрын
Good stuff man!! gives me the courage to tackle projects that may seem limiting at first.
@stanponkratov2698 ай бұрын
Thanks!
@gilrobertonavaperz27018 ай бұрын
Más de una hora mirándole el lomo a este gay
@Fly-SanDiego9 ай бұрын
Flip flops and cardboard boxes. The standard for DIY garage mechanics for years.
@numbnutz6269 ай бұрын
That was so beautiful. It's my dream to go there someday. Thank you.
@ladjkaoz9 ай бұрын
great content. 👍👏👏
@ladjkaoz9 ай бұрын
would you show what or where does the tendioner push... I may had miss that part.
@ladjkaoz9 ай бұрын
why not just remove all that old platic... just use new tensioner...
@MatthewWong9 ай бұрын
Just decided to try it out. My plastic was cracked anyways
@hydn7910 ай бұрын
Did the ticking noise go away or is that something else?
@MatthewWong9 ай бұрын
That's just the n20 engine
@MatthewWong9 ай бұрын
Injectors
@EmmaRides10 ай бұрын
I can hear Abba @11:00
@mingelius206 Жыл бұрын
Is that oil good for hot area
@MatthewWong11 ай бұрын
Not entirely sure. Perhaps consult with local dealer? f30.bimmerpost.com/forums/showthread.php?t=954409
@r3gflm916 Жыл бұрын
How was well was your car running when it was like this? Loud? Misfires? Error Codes? Love the videos you took! Thanks man,
@MatthewWong Жыл бұрын
Misfired at first but I realized it was becuase I didnt have one cylinder hooked up (ignition coil). Freaked me out. But after it ran fine! Just a bit of smoke on start up since it sat for so long. No codes
@Ricardo-eg3wn Жыл бұрын
Please tell me how you have a f30 with power steering. You don’t have power steering. There is no fluid. It’s electric guy.
@robzilla609 Жыл бұрын
Take the spark plugs out before turning the engine over. Next time. It will be beneficial for fighting compression.
@alexanderstefanxandraswedi5835 Жыл бұрын
Welcome hade been Cambodia
@ramiropantoja723 Жыл бұрын
Donde el taller Diresion
@brandongarcia5116 Жыл бұрын
Anyone knows how to take out the cap from below if it’s stripped? 😢 I’ve been trying for hours
@MatthewWong Жыл бұрын
Oil drain plug is stripped?
@brandongarcia5116 Жыл бұрын
Yup, I went to the store to get a full set of Allen wrenches and none worked, it keeps slipping 😓
@VinnysV8 Жыл бұрын
Very informative and fun, ty for the help!
@hectorsuarez6166 Жыл бұрын
Gracias por tu video hermano 🇨🇴🇺🇸
@TheDonz Жыл бұрын
I got a new timing chain installed, mine also doesnt move at all
@eznuk66 Жыл бұрын
Great. how do you set the HNCS-Mode? Is it automatically if you choose Normal instead of Hlog, D-Log or D-Log M?
@guccipig2782 Жыл бұрын
Was your car running fine before you did the timing ?
@MatthewWong Жыл бұрын
Yep
@guccipig2782 Жыл бұрын
@@MatthewWong oh ok. Cuz I have the same car and my timing chain is just as slack as yours in the video. And I’m getting a misfire on cylinder number 1. I’ll replace the injector and coil to see if it fixes the misfire. I already did all four spark plugs just recently.
@romanobrown5592 Жыл бұрын
@@guccipig2782 what was the code
@guccipig2782 Жыл бұрын
@@romanobrown5592 the injector wasn’t seated right so the Teflon seal kept melting away. I fixed the issue now. It runs fine.
@RandomVidz9_ Жыл бұрын
Hey when adding coolant do you have to have all 3 bleeder screws open then when it starts leaking out coolant close it up and start bleeding procedure? If so how open do u have the bleeder screws all the way out or half way?
@MatthewWong Жыл бұрын
I tried all three at first until they started leaking out. Then I tried each individually about 2-3 more times to make sure there was no air
@beautycm27 Жыл бұрын
Women: You don’t have to pull off the wheel. Turn the wheel to the opposite side and pull off covering. Then fish your hand in and remove the bulb. Watch the front lamp as you replace the new bulb. Use your tactile senses and this converts to an easier less laborious task. Benefits of small hands 😅
@Centralflorida22 Жыл бұрын
❤
@SOHAIL50280 Жыл бұрын
Thanks brother
@gabrielpagliaro1834 Жыл бұрын
hello and congratulation can you send me price of that tool and price to send ti miami? thanks gabriel
@weldon29 Жыл бұрын
Is the new one more durable than the old one?
@MatthewWong Жыл бұрын
Not sure but BMW did upgrade the parts
@Mid-Valley-Clean Жыл бұрын
Your in Oregon I’ll help you switch it out I’m going to do mine!
@MatthewWong Жыл бұрын
I did mine last summer! I have a full video up on my channel
@RandomVidz9_ Жыл бұрын
Do u have to open up the screw during bleeding procedure? Cuz i mostly see them just pour coolant in then start bleeding procedure, they say the water pump will do the work and take out the air and then u just top it off with more coolant, is that true?
@pericodelospalotillosverdes Жыл бұрын
This purging procedure is indicated by the mark, when the electric water pump is changed.