Just found your channel. I really like this lathe. Do you still have it?

Perfect. Thank you

Good job thanks for the video

Damn - this man moves fast.

question. I think there is a mount already installed underneath my quad. approximately what is the measurement of the space between the ears that hold the A frame connected by the bolt and cotter pin?

Great job hanks for the video

Care if I copy you for my camper frame? Also how much did the wood cost yu?

jamie, great wood working, nice job. Constructive criticism, I'm certain that the Pioneer unit is out of phase, maybe I can help with your speaker wiring, and maybe i am wrong but its all i know in life. haha If you listen to a Beatles song your gonna get Paul or Ringo, but not both! Care to reply we can help each other...good woodworking skills man!

Good job looks great Keep building thx for sharing Cheers

That turned out great, definitely looks much better! Slainte, DC 🍀

Can you did a video of how to change the carb?

Bien hecho, te quedo muy bien. Te felicito compañero. 👏👏😉

Beautiful work, Jamie! It turned out great! 😃 BTW, my name is also Mario! 😂 Stay safe there with your family! 🖖😊

Muy buen trabajo y práctico

Check sound bro😊

How the heat we go outside

Nice understandable video thank you!

Man ... with one hammer ... sort of brute force, but looks great. I'd do the soffit though and keep the criters out.

Good job and project thx for sharing enjoyed it Keep building

Congrats on over 15000 subscribers

Nicely done, Jamie! It looks great!!! 😃 Stay safe there with your family! 🖖😊

Just steps away from hauling several commercial mowers and all the essential equipment involved. There is even room for a box for debris. Your living my dream. Cunningham's Lawn Care

Have you had issues with expansion on that table top??

Thanks for clarifying that it's ok to use bed frames! I have a 6'x14' galvanized boat trailer I bought for $200 that had a wooden frame around it. It was rotted all around so I took it all off and I've been wondering if bed frames would work to frame it. I'm hauling a mower and SxS with it, so nothing over around 1200 lbs. Great video!

In many states you need a safety inspection to get a license plate. The state will require you to replace old tires, even if they have little wear on them, which of course is a good idea, so the owner may need to buy 4 tires.

What is the millimeter size of your oil filter cap wrench.

Can some one explain the setting the valves part? I didn't quite understand what exactly was happening haha. I'm about to replace the head gasket for my t2200. wish me luck!

Thanks for the video, easy to follow. Any issues with aftermarket parts?

a tweeter is better

Thanks for sharing. I appreciate the video. You made it look so easy.

Hi Jamie, I am hoping you have some input for me, but first, thank you for the video. I have a LTX 1040. I have not noticed it going slow so much but I have a hard time climbing hills with it. When it stop while climbing i release my foot and push it down and and it wll go a little bit, sometimes i have to do this several times to make a hill. I replaced the belt and seemed to fix it for about 15-20 minutes. I will try and do what you have showed in this video but I thought i would see if you have any other ideas. Thank you and thanks again for the video.

Brilliant. I have an ancient Murray with stick in the middle between you legs. Getting harder to change gear. I have a "spare" tranny so would you say its worth trying to swap or something else I should do first? Thanks a lot for the video!

Good video, I have an observation, wouldn't it be better to do the pocket screws on the rear side members in the afternoon from behind?

I wish I do not have to open the wall or run any pipe

Very common issue on the newer riders, I fix alot of these! Great video!

I have the same lawn mower. The mower should have a constant rounds per minute. However it changes the rpms from time to time (especially when the grass is a bit higher). The engine is than producing blacker smoke. I cleanded the air filter but it doesn't make a difference. Have you got any idea what the problem could be?

fantastica grazie x l'idea me ne costruirò una sicuramente

Awesome job, looks great. I've picked up a 14ft Bonair camper trailer and I plan on using your video as reference while I convert it.

Nice video. I'm just surprised you ever found the locator pins after that wire brush grabbed the green rag.

Sir what State are you in. .?

Side boob 🍓

🤘 awesome!

Can you help me out with my aquarium stand project ???

DUDE WHERES THE VENT OUTSIDE???😂😂😂 where is blowing out the air????

Excellent and truly straight to the point tutoring video from Mr. Jamie List!! You Sir, saved me a ton of money by showing me how to do this myself. I took my time on it And the lawn tractor works and cuts better than before. You even hinted at how to fix the clutch brake and put new pads on! I really enjoyed this project with my son. The two front bolts underneath in the back bracket were easy to get off but a pain to line up and get on properly, but I did it right. Thanks Mr List. I will be watching your videos for more good things in life

How much weight do you think it can handle Like around 1000 pounds

You are a G

Doing the same thing but my big question is... what about the septic tanks?? Not sure what to do there...

😆This doesn't make it louder, it just changes the sound... I get the same effect when I back up too close to a flat metal surface... or if I jackknife my trailer and it comes close to my exhaust... you can get the same effect with a beer can...

Jóia 🎉🎉