THANK YOU!!! ALL I DID WAS UNSCREW THAT THING, SOAK IT WITH HOT WATER, CLEANED IT! AND BOOOOM !! JETS - ON. I OWE YOU A FEW BEERS!! sorry for the capitals

How wide is the air bellow by itself?

That's actually a digital "caliper". A micrometer has a spindle. A caliper has linear travel.

My gosh!! Thank you!!!!! Was not sure this was the one. Happy holidays°

Soooo relieved to find you. I have one of these tubs too. The motor is kicking on & off every few minutes. HELP, PLEASE!

My jets are stuck in my Kohler whirlpool. How can I free them up enough to remove them. I already broke one Kohler removal tools, where the tip broke off. I have a replacement removal tool and don’t want to break that one too. The tool grabbed the back of the eyeball fine, as shown in Kohler’s diagram but it won’t budge.

Can we call you?

Will this fit the existing plumbing for a R75A-C?

I have an american standard jet tub and if water is raises above the air control valve, it leaks terribly, pours water practically, down the side and under the tub. Brand new, installed in Feb. How to fix?

Excellent video, it helped tremendously. Thanks

Dammit just put a ugly timer switch on the walls so you don't have to tair out the tub just to take a peek

Hi where can I order one thank you

thanks man!

🤙🏽

Thanks for the education! Now I think I know how to fix this.

How do we remove them. Thank you

Please demonstrate how to remove from tub. Thank you 🫡

I just want to share that I used an L wrench (Allen key) instead of the tool because I didn’t have one in hand and it worked fine. A couple of them came just the small part of the middle so I put them back and tried again like this video showed and it came back fine after that. Thank you so much for this video! It helped me to finally get a good clean of my tub!

So if I have the first one that needs to be removed with pliers, I bought the replacement cover, but I don't see where I can buy the part to screw it into.

I have 2 clogs in the airline that are a yellowish color. No air will get through access is limited. I assume I have to get a whole cut to get access to the pump in the back. But the lines are clogged with some type of water. That's turned yellow. Any suggestions

Kohler talks about keeping the blower and tub on the same horizontal plane, does this really matter? would it change performance if the blower was in the attic and then routed into a free standing tub?

I’d like to know the part number that is the same on this video.

Where is the pump located on the tub? I have no access panel and trying to cut one hole. Any advice?

Where can I find replacement Vico jet parts. I'm in California and Robert's Hot Tub is out of them. Please suggest a vendor

I nite Dubai dhat on pumpe suge

Where do I buy this controller ?

My valve is leaking on the “inside” of the tub… I can’t find disassembly instructions anywhere. I mean removing the entire fitting from the tub. Any ideas? Thanks in advance!!!

I'm trying to remove mine to clean behind them. Can I buy just the tool? Can I do it without the tool?

Can you replace this if the tub is tiled around?

What if the air button is too hard to push it on and off?

Only the spring eye and outside cover came of the interior piece is stuck , so how do you remove that?

How do I pull the whole assembly from the tub I just installed my new tub and it leaks and that thing is broken

I have a Kohler K-792-N whirlpool tub. There are two switches, one for all the submersed jets and the second for the neck. My problem is that the neck jets will NOT stop emitting water. Looking for best possible causes. Hope someone can help me.

Can I still get a replacement panel?

Can this be used to help heat a swimming pool?

My problem is that the motor doesn’t turn on at all when the button is pressed. What do you think the problem is and what parts do I need to fix the issue? Thanks!

Well engineered one piece...idiots...what a PITA!!!

The reason the stem shaft snaps off is the tab on the valve prevents it from turning 360 degrees. It just takes one person to force it. File off the tab. No more broken stem shafts.

I have what I think are these in a tub at a house I just bought. However the jet has NO notches to turn it out, any advice?

Where can I buy this parts ? Excellent video !!!

The hose not suppose to have water on it or yes?

Cool

So how do I get a hold of you or this particular fan motor? If I want to replace mine do you sell them or you buy them somewhere online or what’s the story?

A excellent video and just where are you located? And do you have those retro kits available for sale and how do I get a hold of you and order one?

Nice theater

Awesome explanation

Thanks for this video! I have a dinosaur system installed in 1987 that might be even older than you're accustomed to seeing. Our pump, display, and probe all appear to run through a Hydrabaths TDS-2 Timer Delay Switch that is now toast. Do you think this retro kit might work for that application?

And how can we afford to make these free helpful videos? We charge $59.90 (+ $12 for shipping) for this part. What a deal!

Why will my hose not stay on my air button?

my problem is when I push the button in mine don't turn off, could it still be the air switch on top of the motor. is there anyway to change the push button. it's located on the other side of the tube with no access to it