AutomotiveEZ

Пікірлер

@ChiqueChiing 9 күн бұрын

Thanks!

@AutomotiveEZ 9 күн бұрын

Welcome 👍

@JVBO55 12 күн бұрын

Thank you! Have a nice day too! 😎

@AutomotiveEZ 12 күн бұрын

😊

@TyrellNoll 14 күн бұрын

Thank you

@AutomotiveEZ 14 күн бұрын

Welcome and be well

@Heavy69Metal 15 күн бұрын

Got this CODE. 2006 Mustang 4.0L V6 EVAP System Leak Detected Gross Leak/No Flow P0456

@mrmidnight32 18 күн бұрын

Would this make my fusion struggle to start after filling with fuel? I have to rev it for 2 minutes after filling with fuel every time now. I’ve already replace the purge and evap a year ago. Never tried the filler cap

@AutomotiveEZ 18 күн бұрын

Likely the under-hood valve the culprit. The purge valve … also shown in video

@mrmidnight32 18 күн бұрын

@@AutomotiveEZ I did the blow test and it didn’t let air through out of the car. But I took that out and cleaned it with no luck

@AutomotiveEZ 18 күн бұрын

@@mrmidnight32 Hello. Did you change the purge valve under the hood? To be clear, you’d follow the evap pipe underhood - where the valve has input and output side. Output must go to Intake or throttle body if you have the right valve. After replacement all codes DTC’s need to be cleared. Engine lamp would be off if they clear correctly. Then you need a good long steady road test on highway to reset monitors. If CEL returns during road test vehicle needs a fresh scan to see what code is set. Sometimes old code goes away and a new code sets in post repair

@MrSkullWolf 2 күн бұрын

@@mrmidnight32I am and going through this currently and didn’t start replacements yet 😢 did you ever get it resolved?

@chimoslocksmith 19 күн бұрын

Thanks again I just did my second sprinter you are the Best 🎉😊

@AutomotiveEZ 19 күн бұрын

Thanks much. Be well :)

@jamesw9971 Ай бұрын

Thank you mate

@AutomotiveEZ Ай бұрын

Welcome ;)

@zSPARTAA03 Ай бұрын

Thank you sir

@AutomotiveEZ Ай бұрын

Thx and be well :)

@Mr.wisdom11 Ай бұрын

Thank you

@AutomotiveEZ Ай бұрын

Welcome… be well

@wgc383 Ай бұрын

A+ on this video, fantastic content and knowledge

@AutomotiveEZ Ай бұрын

Thanks very much. Your words are super KIND. Be assured - I do appreciate you. If the video helped at all that was the goal. :) . Have a great day!

@truckdriver4323 Ай бұрын

Done that many times and still needs someone to remind me on how to do it. I got a good memory, but it’s to short 😂. Thank you sir for the video

@AutomotiveEZ Ай бұрын

Welcome sir :)

@notneb82 Ай бұрын

These stupid mustangs drive me nuts with their poor water management. First my cowl fills up with water and comes into the passenger area and now my damn doors are full of water

@AutomotiveEZ Ай бұрын

Yes the cowl gets plugged up as well. It is frustrating but the Mustang has been very reliable vehicle especially since 80's forward.

@JamieR2077 2 күн бұрын

@AutomotiveEZ thanks! Yes, been VERY reliable, had my 09 for 15 years and 175k, only issue I've had is that coolant fitting that breaks on the 4.0 v6. Then just some weird quirks like this and the darn cowlgetting plugged. .. thanks for the video!

@denysemoore1990 Ай бұрын

Thank you so much! Wish I would've recorded how much water just came out of my door 😅

@AutomotiveEZ Ай бұрын

Lol you’re funny - thanks so much :)

@jamesmix78 Ай бұрын

This is for 14 and newer 13 and older you just push the pink button in the bottom of cup holder to take it out of park. This is for the ones with knob shifter not shift lever

@AutomotiveEZ Ай бұрын

Appreciate, additional input, and hope it helps some viewers. To clarify, for viewers, he is distinguishing between the Shift Lever version, Vs. the Rotary Knob. Thanks.

@jamesmix78 Ай бұрын

@@AutomotiveEZ you’re welcome! These videos are such a big help. Any time I can add additional info I will!

@AutomotiveEZ Ай бұрын

@@jamesmix78 sounds great!

@starshine1185 2 ай бұрын

Thank you! That water noise has been driving me nuts for a while. The door that doesn't collect run off is actually missing one of these filters. Between these colleting water and the drains under the hood getting clogged and dumping water into your floorboards, this generation of mustang winds up a bit unexpectedly soggy. 🫠 Not good at all.

@AutomotiveEZ 2 ай бұрын

Haha. You had me laughing! GREAT COMMENTS… Sure was a soggy era. If you clean the doors - and cowl pan under hood where cabin air filter is - that helps a lot. Also make sure A/C drain in HVAC case is clear. I should try to make those other videos sometime. Thanks for comments and you’re welcome :)

@Peppermint1 2 ай бұрын

Was there a knee airbag on this car? My 2015 Sonata has one right under the column, with a nasty to remove connector - definitely disconnect car battery 15 minutes ahead

@AutomotiveEZ 2 ай бұрын

My vehicle had no knee bags. However I’m familiar. If you have those bags definitely disconnect battery and follow manufacturer suggestions on time lapse before terminal disconnection. Hope this helps. Thanks

@michaelsimon3493 2 ай бұрын

Thanks, 2016 Dodge or Ram Truck Durango.

@AutomotiveEZ 2 ай бұрын

You are welcome. Be well

@ChrisBranleh 2 ай бұрын

If the push clip is broken, is it something that requires replacing?

@AutomotiveEZ 2 ай бұрын

The outer most door - keeps out dirt so it should be functional… thx

@erik6636 2 ай бұрын

Thank you sir I forget how to do this every time

@AutomotiveEZ 2 ай бұрын

Lol you just made me laugh out loud. Lol. Thanks very much. Happy to be of some help

@george5697 2 ай бұрын

Could the error code P0456 cause low mileage??

@AutomotiveEZ 2 ай бұрын

That is a great question. And I have the answer. However - depends on root cause. For example a P0456 can be a leak near fuel tank - smaller size leak if compared to say, a P0455. However - a 456 leak that say was stemming from a purge valve seal being intermittent - that in fact may effect fuel mileage and may even cause a rough idle. Codes stored in vehicles can originate from multiple sources of failure. No ONE code has an exact origin. I hope this helps. Be well

@george5697 2 ай бұрын

@@AutomotiveEZ i replced the canister purge valve, but check engine light remined even after reset. Would you say replacing the filler neck would solve this issue?? Thanks in advance ! Subscribed!

@AutomotiveEZ 2 ай бұрын

@@george5697 Hi George. The top “failed” parts I’ve done on Ford for this code - under hood Purge Valve and/or Filler Neck - the other item is canister Vent Valve. Look at filler neck under car for rust. When they get real rusty they do leak vapors - especially the Easy Fill style filler pipe

@george5697 2 ай бұрын

@@AutomotiveEZ Thank you so much, it's hard to find a good mechanic around my town, thank you very much!

@AutomotiveEZ 2 ай бұрын

@@george5697 you’re very welcome my friend. Be well sir :)

@karinaxo3442 2 ай бұрын

Hi what spray are you using? And do I need to get this cleared by a mechanic, or can I clear it myself. Wondering if they’d fail the inspection for the light.

@AutomotiveEZ 2 ай бұрын

Hi - use any CLEAR silicone spray. CRC is a good brand. If you have a code reader for OBD port you can clear lamp yourself but drive time required to see if lamp comes back on or not depending on success of repair

@karinaxo3442 2 ай бұрын

@@AutomotiveEZ okay, not air? Saw some people using that. Thanks!!

@AutomotiveEZ 2 ай бұрын

@@karinaxo3442 Hi, you may blow compressed air - gently - to remove any debris. The lubricant (only silicone) is used afterwards

@cailynwylie7108 3 ай бұрын

What’s the piece called because I tried looking up plastic plug cover for front door or anything along those lines and can’t find it but my passenger side is missing them

@AutomotiveEZ 3 ай бұрын

Hey there… I would call Ford Dealer Parts Dept and tell them you need the plastic plug for bottom of door drains…. It’s not really a plug, because water flows through it.. so it’s sort of a plastic screen/grille. I’m just not sure of it’s true name

@notfake2460 3 ай бұрын

Thank you! can't believe how easy that is

@AutomotiveEZ 3 ай бұрын

Thx much

@jessestroud1819 4 ай бұрын

I couldn’t believe that anyone could do this short of an explanation and not make it drag on for 10 minutes. Thank ya sir!

@AutomotiveEZ 4 ай бұрын

I do appreciate your words. I try to never talk about unrelated nonsense and simply focus on the repairs, or task at hand. Thank you!

@bornfree7881 4 ай бұрын

Thank you!

@AutomotiveEZ 4 ай бұрын

Welcome buddy

@diph3732 4 ай бұрын

Do I need to disconnect the battery before changing the purge valve? Thanks for the video

@AutomotiveEZ 4 ай бұрын

It is not a bad idea. But after the disconnect you have to reset clock - radio and basic settings

@Ding66_ 4 ай бұрын

Thanks for simple clear guidance. Needed Some hard pushing on accelerator pedal and brake to clear mine

@AutomotiveEZ 4 ай бұрын

Thanks much for the kind words. Very happy the video helped you out - be well

@ejneenan9329 5 ай бұрын

Question: no problem filling the tank on my 2015 Escape, but after filling. It's a hard start...almost won't start. Haven't done a code source check yet.

@AutomotiveEZ 5 ай бұрын

Suggest new purge valve

@ejneenan9329 5 ай бұрын

Thanks! @@AutomotiveEZ

@AutomotiveEZ 5 ай бұрын

@@ejneenan9329 You’re welcome. Is an inexpensive - first step. A hung up purge valve will cause an extended crank many times. If it does not help please see a local mechanic you trust. Be well

@Niqua10023 5 ай бұрын

I have this problem when it rains. The water gets into my passenger side. It's so annoying. Plus, I got to replace something. In the middle is clicking noises but I know what it is it can be easily replaced.

@AutomotiveEZ 5 ай бұрын

Maybe try to start with flushing of bottom of door first as outlined in video and then see how it behaves after? It’s a solid starting point. Thx for posting!

@youssbldj9922 5 ай бұрын

Thank u so much sir , you saved me trip to the shop 💴

@AutomotiveEZ 5 ай бұрын

I appreciate. Happy to help

@RideAcrossTheRiver 6 ай бұрын

What about P1450?

@AutomotiveEZ 6 ай бұрын

P1450 is not related to anything in my video. A P1450 needs diagnostics

@RideAcrossTheRiver 6 ай бұрын

@@AutomotiveEZ Ford states P1450 has to do with purge valve and canister, but my canister is fine. We are replacing the purge valve which also seemed to test fine. I have found dirt and water around my filler neck pocket, however.

@Theundisputedtruth 6 ай бұрын

Nice video I can't get my bottom , bolts to hold in bottom half of the steering column lined up any advice anybody ?? Thus repair is all column pretty much

@AutomotiveEZ 6 ай бұрын

Do you have two studs with nuts and two bolts on your column? There are various configurations

@Charr9TV 6 ай бұрын

Mines say p0455 took it to auto zone n the code said a egr vacuum solenoid but can’t find no video to get it fixed my gas only last a day or two

@AutomotiveEZ 6 ай бұрын

The EGR system would not set a P0455 code. The 0455 code is for evaporative emissions system. The EGR is a separate system. So you may have more then one issue. You should find a REAL mechanic near you to inspect it. It may cost a few bucks but is worth it in the end

@fcan222 7 ай бұрын

This is the only video that doesn't require unplugging any plugs or harnesses under the steering column...is that even possible? Anybody successfully replace the rubber bushing this way besides him? I'm a little hesitant because all other videos require you to remove many plugs and harnesses.

@AutomotiveEZ 6 ай бұрын

You just need to be careful and aware as you lower column down. If any harness is being stretched - then you unplug. Hyundai and Kia have at least 3 different configurations of this column - where motor is mounted in diff area. In my video - I left it plugged in because it was possible. I’m a career mechanic and everything I post is factual. No editing either. Thx for posting and best wishes

@fcan222 Ай бұрын

Thanks for your video. I finally changed the rubber bushing and that fixes my steering noise. Your way is one of the easy and quickest. For a first timer...took me a little over an hour.

@user-rt9em9zx3h 7 ай бұрын

Quick and thorough

@TheWretchedSpawn 7 ай бұрын

Thanks had mine for years and it started today

@AutomotiveEZ 7 ай бұрын

Thank you

@trewatson9484 7 ай бұрын

Worked perfectly appreciate you for making this video bossman…😂 i broke my clip trying to take off that cheap ass clip though..and i couldn’t find that cleaning spray you had so i used a little wd40

@AutomotiveEZ 7 ай бұрын

Thank you for the kind words

@LookSquirrel 8 ай бұрын

Simple. Quick. Informative. Thanks, good sir.

@AutomotiveEZ 8 ай бұрын

Thank you as well sir

@zipjay 8 ай бұрын

Thanks! I had the notification come on shortly after replacing my battery. At least they make it stupid easy :)

@AutomotiveEZ 8 ай бұрын

Thx :)

@simont1709 9 ай бұрын

Hello does anyone know if this fits a 2018 Elantra GL mechanic says Hyundai wants to fleece people by selling the entire steering column and won't sell the coupler seperately.

@AutomotiveEZ 9 ай бұрын

The coupler is available you just need a good mechanic that knows the job

@simont1709 9 ай бұрын

@@AutomotiveEZ do you have a part number by any chance? Thx 🙏

@AutomotiveEZ 9 ай бұрын

@@simont1709 The common coupler, is part # 56315-2K000-FFF

@simont1709 9 ай бұрын

@@AutomotiveEZ thank you thank you 🙏🙏

@JPOFett 9 ай бұрын

Tons of dirt in my door drains. All cleaned and ready for the rainy season. Thank you

@AutomotiveEZ 9 ай бұрын

Thanks for the comment. You are welcome :) Be well

@saddiemarie96 10 ай бұрын

I have 2018 ford focus hatchback going to try the gas area then go to the front .: where do I order stuff from

@AutomotiveEZ 10 ай бұрын

If you need any fuel system parts I’d use a Ford Dealer parts counter. Aftermarket parts are usually junk

@saddiemarie96 10 ай бұрын

I have ford focus hatchback 2018 I have this code I need help it says small evap leak

@AutomotiveEZ 3 ай бұрын

Sorry I had missed this comment in past. Do you still need help?

@danielfreeze4394 10 ай бұрын

Damn good video one thing to add 2014 kia forte i have only has 2 studs and 1 bolt in the back that goes in horizontal in a bracket in a horrible place. Its behind the motor, but you can get to it with a ratchet.

@AutomotiveEZ 10 ай бұрын

Hey - thx for the reply. I know all about those because I work in a busy shop. Lol… The car in my video was not that style. I’m glad you mentioned it though if it helps someone. One other thing - they have about 3 different spots they put the motor (on column) depending on model. But the coupler / bushing we replace is always same and the motors always seem to have just 3 bolts holding them. Be well!

@solacemusic242 11 ай бұрын

My question is: is it dangerous to not replace the bad rubber gear? Is it just an annoyance?

@AutomotiveEZ 11 ай бұрын

When the rubber “interface” gear - a bushing - goes bad - it can cause wear on steering column and electric steering motor as well. And I would never call a worn part a safe part. Hope that helps you

@solacemusic242 11 ай бұрын

@@AutomotiveEZ Thanks! I will eventually fix, but do I wait for Kia to fix for free (several months out) or do I pay my mechanic $500 because it is not safe. My mechanic said they just replace the steering column, which sounds weird if that $2 part is all that is wrong...

@AutomotiveEZ 11 ай бұрын

@@solacemusic242 if it is covered under a warranty or recall, have the dealer handle it. If you have to pay just choose a mechanic you are comfortable with. It is very rare that the column is faulty. I always replace the bushing. I have done dozens of them! Only one time did I have a bad column in a Kia. Just once. Hyundai and Kia are same company using same parts and engines too… just an FYI

@hill161 11 ай бұрын

any advice on removing a broken plug cloest to fire wall?

@AutomotiveEZ 11 ай бұрын

A broken glow plug? If that is what you mean you should have a professional mechanic look at the situation for you. It is not something I can do unless I was there in person. Worse case scenario is cylinder head removal but there are other things you can try first. Again… find a solid diesel tech if you broke a glow plug

@r77gan 11 ай бұрын

Thank you! This video helped me immensely diagnosing the issue with my ML280cdi no warnings crank no start was advised to do glow plugs then fuel filter I had enough watched your video and this was the exact issue! Was about to throw parts at it. I’m no mechanic but this really confused me. Glad to have salvaged my ML! Thanks a million!

@AutomotiveEZ 11 ай бұрын

Thanks so much brother. Really happy you found it helpful

@winstonbrown1516 8 ай бұрын

@r77gan All these years I thought I never had a Brother.., till now. UK, ML280 06.., giving me the biggest Nightmare for 7 straight months. Crank-No-Start. Purchased: Crankshaft sensor. Camshaft sensor. 6 Glow plugs. O-Rings. Vice. Mini Diamond Cutting Disc. Torque wrench. Hold-Down Bolts x Line hoses. 7PC Professional Diesel Injector Seat Cutter. Hours, upon hrs, upon hrs, upon days, upon days, upon months. Started the other day, then stopped. Pressure! I believe I'm there now and will re-install the last offending injector tmw, 8/11/23. 🤞

@cubitbrown843 11 ай бұрын

U didn't show the spray your using

@AutomotiveEZ 11 ай бұрын

In the video I mentioned to only use a clear silicone. Not a petroleum lube. The brand name does not matter. However - I generally use CRC brand clear silicone. Clear silicone sprays out like water. There is a white silicone product on market.. that looks like lithium grease and is sticky… Stay away from white silicone when it comes to gas tank and evap seals

@TimJoseph08031990 11 ай бұрын

Thanks for the video. I did this on the 2014 Subaru Forester 2.5 Liter Touring with EyeSight. I was able to remove and replace the hose with my hand. The old PCV valve was plugged up with oil, so good thing I replaced it. I tightened the new PCV valve close to 10 ft. lbs. of torque.

@AutomotiveEZ 11 ай бұрын

Sounds great. And sounds like you did a thorough job! Thx for comments

@Axerotic 11 ай бұрын

Thanks for your help

@AutomotiveEZ 11 ай бұрын

Thx for the kind words. Welcome :)

Ең жақсы KZbin

Пікірлер