If im doing this my soot mass measured is increasing and calculating is falling.

Where is the control unit located, is it only one?

Thank you, this continues to be an excellent video that has helped me do the job today !

People need to get their sound descriptors correct. That's s vibrating noise, not a rattle.

I have this on an Audi a3 saloon 2015 1.4 tfsi 150bhp. Comes on between 1800-1900k revs.

Excellent thank you for posting

Check your timing chain tensioner , Try clean your throttle body, or replace a new one , i had the same issues like these before ,

saw that sh1tty black plastic and knew it was a jeep or a bishi

What if my wiring is melted

Audi is the worst car I have owned it’s a money pit full of problems

Cheers lad, have the bulbs, was just wondering if it be hardship or not. That is handy.

Timing chain issues cause this sound. My car does the same thing. Could be a combination of your motor mounts causing vibration also. This is what my issues are and it sounds exactly like this, but only when I’m at idle and stopped.

Really helpful content just what I needed my local garage wanted £55 for a bulb replacement many thanks..

Why did Audi make it so difficult to change a simple bulb? Like damn. Could have easily just made it so your hand fits inside the housing without having to remove the entire assembly

Find what it was ? let me know please

Same noise I said forgot it that's the only issue with my car.

In sfârsit un videoclip cu zgomot ca la mașina mea. Săptămâna viitoare schimb suporții motor . Voi ce a-ți mai rezolvat?

Had to pay £10 at Halfords to get this done . The guy never used any spanner’s took him less than 5mins .😮

Video is spot on. Totally helped me replace the bulb in my wife's A4 Avant. Only variation was my wife's car has the Xenon bulb. Spendy replacement...

Mine didn't come out like that! Had to remove more screws break some plastic and swear a lot

Update for everyone: I have found this problem is related to the bonnet stay. Mine was missing its grommet and causing the front bumper to rattle. Try removing it

Hola buenas, cuando intento entrar a acceso de seguridad, al meter el código me pone: controller refused to send a sed, service not supported in active session. Sabes como podría solucionar esto? Un saludo y gracias

Thanks for making this video. It was helpful for replacing the blown bulbs in my wife's Audi. I wish it would stop raining though!!

How long did you leave the rims to dry before you put them back on the car?

How do you know when it’s finished ?

Yes motor mounts everyone.

Try Checking Motor Mounts

Thanks for the video and all the comments; very helpful.

Update?

Huge thank you for the video mate, would you mind telling me where the engine coolant temp sensor would be located?

Have the same noise at rpm 1100. The noise occurs at reverse or driving. Crawled under the car, front exhaust pipe is shaking and front engine mount is also bad. Not sure what is happening. Will change the front engine mount, seems easy and the part is $30.

Did you guys found out the issue with the rattling noise ? As am having the exact same issue 😕

Any luck?

I want to use an oil pump. Where do I connect it for power? Thanks

What did you do to the clamp with the screw driver. Cheers

I would have struggled mightily without this video thank you 🙏🏻

No problems after replacing with error Messages on Display ??

Well done!

I'm looking for the booster sensor, can you please tell me where this is

Been looking everywhere for the G31 sensor on my 2014 Audi Q5 2.0 Quattro engine still cant find it lol 😂

Can you force a re gen to re start if you have stopped halfway through a previous regen

Thank you sir ! Unfortunately thanks to you now I know that i have oil leak from EGR valve

Isnt there an oil check thingy?

I have excessive mount of oil in my engine. Where can i shove the hose inside the engine and start sucking oil? And for US citizens. Euro model don't have old skool dip/oil stick.

Thank you very much!

Worth the watch thx fam!!! Da hood....

Great camera work.. Just show the side of the house next time and we'll take it from there

very educating and useful review thanks a lot. great video 👍

I just did this job and it was easy thanks with to this video. The fasteners are all T30 though.

I have this same exact, to a tee noise in my car, can only do it in drive and won't do it in park. It's been driving me crazy for months