I have a switch over problem on my 2004 Lexus LX470 is it a similar problem and fix?
@umeshchandersharma81486 ай бұрын
What is the price of 1 machine
@robinshelko22767 ай бұрын
*Promo SM* 😈
@adamr4569 ай бұрын
I know that voice, Anthony! lol. 😂
@whitbygappa5762 Жыл бұрын
😪 promo sm
@dineshbhoibhoi583 Жыл бұрын
Sir you have vacancy I am air conditioner duct fitter 15 years experience in Gulf
@65mustangat192 жыл бұрын
Who makes that bead roller
@ianmoore5252 жыл бұрын
Well done Dave, I’m really impressed with what you have achieved since I left. All the best to you Gail and all the crew.
@SheetmetalLife2 жыл бұрын
That software looks good ;)
@nategin90092 жыл бұрын
Need something like this in my shop😂
@AutomotiveKarnage3 жыл бұрын
Beautifully explained boys. Thank you very much.
@iancook69463 жыл бұрын
I have a 2012 Prado 150 series with a sub-fuel tank and have just had the fuel transfer pump replaced. However the fuel light is now flashing ( the fuel light NOT the one with the 2 lines of dots underneath) when I get down to about 700 km to go - fuel gauge approx at middle.. I presume this is when the tank changeover occurs? I topped up the fuel and the light went off, but it came on again when the fuel went down to approx the same level as before. I thought the ECU may need resetting and did this but no change. I have also checked the relevant fuses. Any solutions / ideas????
@belcher283 жыл бұрын
hi @Ian Cook did you have any solutions to this problem? My 2012 Prado 150 has been doing the same for a while. Now however, i can't seem to fill the tank much over half as the fuel filler clicks off as if the tank is full.
@bobodobalina3 жыл бұрын
What does a brilliant piece of machinery ike that cost
@freakyaussy3 жыл бұрын
Wasn't it nice years ago when you didn't have to guess , you could just refer to the workshop manual. We should be able to buy them still
@boonjabby3 жыл бұрын
how the heck did you remove the "large fuel line" at 0:36? Please help, i literally spent 20 minutes attempting to take it off and run out of daylight :(
@Richard-Tanya3 жыл бұрын
flat screwdriver in and gently open the clasps holding it secure whilst you pull at same time :)
@boonjabby3 жыл бұрын
@@Richard-Tanya thanks for the reply. I got it off eventually. Seems like the last person butchered it and it overflared the clasps
@fxsrider3 жыл бұрын
That is an odd looking dolly it bangs into. That probably cost quite a chunk of money. I would expect a better solution than that attached to the Z-axis.
@MADBONE04 жыл бұрын
would it be ... a good idea or a bad idea to widen that hole with a 4mm drill bit ... to stop more particles clogging? obviously we want to stop the particles but it needs to be stopped at the Fuel Filter thats its job haha
@boonjabby3 жыл бұрын
don't enlarge the hole. it was created like that to ensure the venturi effect works. if you make the hole bigger, the vacuum action will reduce
@justuswalker-lovell2492 Жыл бұрын
Probably needs the backpressure to create the right amount of vacuum
@roccosciarroni35564 жыл бұрын
Molto bello lo faro io prossimamente
@naveedaslam96914 жыл бұрын
Please shut the music
@darryllyrrad48594 жыл бұрын
Mine is a 2003 first month of the 120 series I don’t have the internal pump as shown in the video think mine uses main pump I had no blockage in Venturi still NFG note my model does not have a transfer filter
@taymanjeppy4 жыл бұрын
What is your pressure and feedrate? I'm having issues cutting through triaxial fiberglass and usually end up needing to hand cut parts parts that weren't cut all the way through with scissors.
@tandemwings47334 жыл бұрын
Well done Aussies..!!!
@sarwansingh75374 жыл бұрын
Plasma nozzle cutting size
@147684 жыл бұрын
I don't know why these videos don't get more views and comments. They are freaking fantastic. No screwing around, right to the point, and loads of fantastic information i've never seen anywhere else. Thank you
@user-C174 жыл бұрын
Parabéns.. congratulações desde o Brasil.
@tarek68974 жыл бұрын
Hello, I own a company specialized in air conditioning and would like to communicate with you to acquire this machine [email protected] Facebook /SARL HVAC DEUX MILLE
@adamwicks7684 жыл бұрын
This helps a lot. I pulled mine out and found the pump had been replaced in the past but not plugged in! I also found the transfer filter blocked. Plugged in and tested the pump and renewed the fuel filter. I didn’t check the Venturi though and put it all back together. Seemed to work for a while but has stopped again. I’m going to have to pull it out again!
@dillusvlog38464 жыл бұрын
Pls contact number
@joebaroudi22934 жыл бұрын
Hi Shem Tewkesbury, my prado150 1kd 2012 flashes the fuel light on/off despite fuel gauge at middle. When I fill up, the flashing fuel light stops flashing...Do u think venturi or secondary fuel filter?
@LeonelFNicaragua4 жыл бұрын
Oh Man, I wish I had seen this video along time ago, im having this problem right now on my 2008 Prado. Thanks alot
@mariskameszaros64134 жыл бұрын
Me too! Just got a quote from Toyota, just over $2,000.
@joebaroudi22934 жыл бұрын
What is the problem? What are the symptoms?
@joebaroudi22934 жыл бұрын
What was ur issue?
@LeonelFNicaragua4 жыл бұрын
Engine would stop running with the fuel gauge at 1/2 a tank. Toyota dealer changed senders and dashboard ($2,000), and still had the problem, took IT back and they said IT was the jet pump that was only getting half of the fuel out of the sub tank, after watching the video I went to another shop, they just cleaned all the fuel system and problem is gone ($80).
@joebaroudi22934 жыл бұрын
@@LeonelFNicaragua thnks, mine fuel light flashes while gauge is midway, but car still runs (although I didn't dare to drive long before refill). Do u get fuel lights flashing?
@warrenblackburn57234 жыл бұрын
hi, does the fuel pump stop working when the jet pump blocks?
@nicolasgritter4 жыл бұрын
Could you tell me what is the speed of the spindle and the feed rate to machine this material thanks
@ramprasath42264 жыл бұрын
Machine details
@cgarobotica30174 жыл бұрын
Hi, how are you? I'm interested in the team, but my question is how the toolpath for the tangential and the other heads is generated?, with what software? Do you deliver it with the machine? How do I learn? thanks
@1964dallas4 жыл бұрын
Wear is the sender , mine is up and down all the Time even when I have put fuel in it .
@Richard-Tanya3 жыл бұрын
2 senders, one in rear tank and one on fuel pump module in main tank
@sgtunix4 жыл бұрын
I have a Prado 120 and the car stopped today seemingly due to fuel starvation. I had about 100 liters fuel, so 90 liter in one tank, about 10 liters in the rear tank. After waiting for the fuel pump and car to cool down, I was able to start again. Do you think the culprit is probably the venturi? I suspected that the fuel pump itself is the issue.
@ВладимирКольченко-б7ш5 жыл бұрын
An engineering solution is not the best. Additional difficulties and costs were spent so as not to rotate the workpiece, however, the complexity of the implementation and the price are equal to the option with the rotation of the workpiece. Very poor ventilation implementation. I think that the motto of this project is: it works and is already good! We in Russia say: touch the left ear with your right hand.
@dooplernet5 жыл бұрын
where i can find more information about this software
@tariqhassan3875 жыл бұрын
Price Pls ..... [email protected] .... How thick & hard surface it can cut , what about vegetable leather or split leather will it be able to cut it ?
@Westerworld5 жыл бұрын
My Prado has an issue, and I am wondering if this is the reason. When I start my Prado (KDJ120 - 03/2006), the engine turns over and start, but immediately shuts off again. Batteries, keys & immobilizer are checked and works just fine. I pulled off the fuel supply line on the fuel filter in the engine compartment - turned over the engine - and none fuel came out. I still have to check the fuel supply pump. If its working - could this be the reason for the issue I am experiencing?
@1800bernie5 жыл бұрын
Hi Andre, it’s my vehicle in the video and one of the symptoms is that it appears to be out of fuel even when the fuel gauge shows there should be fuel in the tank. So if your fuel gauge says you have fuel and you can’t start it try putting fuel in with a Jerry can. It will be slow to go in (up to 10mins to get 25lts into the tank) and prime the fuel lines with the primer on the fuel filter until it’s firm and try again. If it starts and runs I would say you are having the same issue I was. You will be able to drive until that fuel from the Jerry can runs out. Good luck
@Westerworld5 жыл бұрын
Shem Tewkesbury Thanks! I ended up with a total disasembly of the fuel Line. I didn’t find any jet nozzle though - But i clean out the whole Fuel Line, and now it runs smooth again. Thanks for the video Shem!
@meganjamieson87665 жыл бұрын
Its called a jet pump. It uses a hi pressure, low volume flow through a venturi to create a high volume, low pressure pump. Simple but effective, at least until you get junk in the venturi.
@joebaroudi22934 жыл бұрын
Hi, is secondary filter at the suction or discharge of the jet fuel pump?
@TulzIndomic3 ай бұрын
Me iv got problem like this with 3.0 prado land cruiser 1998 model
@AOKEPLOTTER5 жыл бұрын
good machines, our equipment only can cut the foam within 100mm
@classic_craig5 жыл бұрын
Cool as
@didiDanaila5 жыл бұрын
price?
@andrewspike82575 жыл бұрын
It’s an XBeast
@worldadventureman5 жыл бұрын
Company makes video to promote sales of its CNC machine....fails to answer anyone's questions. LOL