4 сағат бұрын
5 сағат бұрын
8 ай бұрын
8 ай бұрын
8 ай бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Пікірлер
@parwindersingh1279 15 күн бұрын
😂😂😂😂 really this 😢😢
@2strokefanatic578 13 күн бұрын
yea but i love the powersaw its so loud and beefy
@Monroe1516 15 күн бұрын
WTF !! that music is rotten to the core
@2strokefanatic578 13 күн бұрын
sorry in my later videos thers no more music due to possible music legal propblems
@Robochoa88 Ай бұрын
Broo thats running bad 👎
@2strokefanatic578 13 күн бұрын
yes it a video on possible problems on this powersaw and it had carb problems
@Robochoa88 Ай бұрын
Did you take the choke off once it started???
@2strokefanatic578 13 күн бұрын
it has carb problems
@steveburling7072 2 ай бұрын
Shoulda taken the blade out
@2strokefanatic578 13 күн бұрын
the saw helps as the rotational balance for the saw
@edwinlopez8564 4 ай бұрын
I am needing a Viza scooter transmission, could you tell me?
@2strokefanatic578 13 күн бұрын
you can hopefully find a viza transmission or one close to what you need on ebay
@drayvogel2283 4 ай бұрын
Curious, when I add oil to mine and run it, it spits all the oil back out through the carb. Any idea what would cause this?
@cbandhamradiostations4845 4 ай бұрын
Hi can the flywheels go faulty
@2strokefanatic578 4 ай бұрын
yes flywheels can go faulty because some newer flywheels have a built in key that might get sheared if not tightened down, other than that i dont know of any other problems concerning flywheels
@ringsidejudge4302 6 ай бұрын
What a waste of time , listening to stupid music . Really annoying , I will remember this channel and never visit again .
@rogerembry4777 6 ай бұрын
It needs new rings
@machfiver753 6 ай бұрын
Paint thinner works good too. Hope you're fanning the fumes away. lol
@philliphall5198 6 ай бұрын
In order to remove the carb on some of them I hack saw a tad off cover to remove carb, don’t hurt anything eather 😊😊😊
@philliphall5198 6 ай бұрын
If compression is low I bring piston up to top and pour some B12 or sea foam in it , let it set for several days, dump and refill up to 10 times
@piotrpakula3089 7 ай бұрын
Does this saw have a ring joint visible in the muffler hole?
@dieselmechanicsam 8 ай бұрын
Looks like a late 80s saw... began production in 1981. A homelite Zip chainsaw would be a early 60s style saw....
@DaleCline-n6x 8 ай бұрын
Where do you get a new coil for a 440evl
@2strokefanatic578 8 ай бұрын
ebay might be your best bet or parts sites like oem replacement parts
@billrector 9 ай бұрын
Where is part 2?
@2strokefanatic578 9 ай бұрын
Hello sir I am sorry to inform you that there will not be a part 2 in this series, at the time I needed to get it fixed the next day for a person who owned it, I am sorry that I was not able to upload a second part where I rebuild the leafblower it would have been very good information but I did not have the time to set up and do the recording, please accept my humble apology and I'm very sorry I failed you as a subscriber
@2strokefanatic578 9 ай бұрын
Also next summer I intend to find another still blower and video my rebuild of that 2 stroke engine so you will have a part 2, also there are other you tubers that have a complete tear down and rebuild of a sthil blower
@MrTem68 9 ай бұрын
I have a homelite 330 it wouldn’t start so I replaced the carburetor boot , fuel line and filter put it all back together and it will start and run a few seconds then shut off. Can’t keep it going do you have any idea why it would do that? It acts like it’s not getting fuel
@2strokefanatic578 9 ай бұрын
maybe cleaning the carb and looking at the diaphragms need to be replaced if they are old and stiff
@bjemdwbesq3 10 ай бұрын
maybe it's just me but seems like you'd need a carburetor
@2strokefanatic578 8 ай бұрын
i just wanted a little gas in the engine to have it rub for a short quick run i like doing that so i know that the compression rig and piston and cylinder are ok
@sicebiphilasande7871 Жыл бұрын
I can able to removed the blade and put a saw?
@iskandarsuhaili Жыл бұрын
Same thing happen to me, the repairman said it is too old - no Sparepart
@2strokefanatic578 Жыл бұрын
You can sometimes get spare parts from eday or other online wedsites
@KTHKUHNKK Жыл бұрын
That is the exact one I have. Mine still runs great but I'm curious to watch your video now. I hope you do a good job and can hold my interest.
@bryanfoxx2292 Жыл бұрын
HORRIBLE music, had to stop watching within 2 minutes. Ugghh
@yogsothoth9515 Жыл бұрын
first :3 Loving the videos so far <3
@yogsothoth9515 Жыл бұрын
I love your videos. I'm going to be rebuilding a bg 50 and i'm watching your videos to prepare myself.
@2strokefanatic578 Жыл бұрын
That's good remember that good oil seals and gaskets seals are needed for the motor to work
@yogsothoth9515 Жыл бұрын
@@2strokefanatic578Yea it's not making enough compression so I'm hoping just replacing seals is enough to fix it.
@2strokefanatic578 Жыл бұрын
also check piston and cylinder wall for scuffs and vertical damage, and check ring if its moves and not stuck and has not to much wear and is pretty much in good shape also check the gasket betwwen the cylinder and lower part if it leaks or looks wet replace the gasket there can be a loss of compression for the downstroke to push the air gas mix to the top of cylinder to be set off by spark ok thanks and please like and subscribe and tell your freinds about me
@2strokefanatic578 Жыл бұрын
o yes i forgot in a stihl motor there will be tree seperate parts the cylinder the mid part and lower like an oil tub the first 2 parts you can seal with a gasket the liwer parts you will need sealent to seal it up it does not use a gasket
@yogsothoth9515 Жыл бұрын
@@2strokefanatic578 thank you so much for the advice. I have 3 service manuals for the blower. Between those and your channel i feel confident with dealing with it. And I have told my other 2 stroke fanatic friend about you
@tedsmith7486 Жыл бұрын
Thank you for your military service Sir. I appreciate the knowledge you've passed down with these videos you've made I just wish I'd have seen your channel sooner man honestly I think your videos are awesome from what I've seen. Thank you again & God Bless you & Yours hope all is alright.
@2strokefanatic578 13 күн бұрын
thank you sir and its my pleasure not only to enterain but to also inform you of things you can do to help yourself in the future
@tedsmith7486 Жыл бұрын
Thank you! I never knew that the oiler worked in conjunction with the crankshafts momentum that's quite interesting. Thanks for taking your time to make this video.
@tedsmith7486 Жыл бұрын
My apologize I didn't think the music was that bad & I appreciate that you didn't speed through the video & you showed it in real time without editing/fast forwarding it. I personally don't like it when people do a time-lapse because 99% of the time the one part I was trying to see is sped up & I'm no closer to fixing what it is I'm working on. I can agree that some in-depth analogy/narrative or whatnot won't hurt but it isn't necessary either I appreciate you taking your time to do the video honestly you've got a new subscriber here.
@tedsmith7486 Жыл бұрын
I know I'm a bit late to the party here, I just don't understand WHY people in the comments are BITCHING about the music I truly get annoyed when people are so stupid that they take more time to write a comment about something they willfully sat though & had the option & free will with NO OBLIGATION forcing them but it's NOT only that they watched on their own by CHOICE but THE THING THEY NITPICK is COMPLETELY OPTIONAL as well!!! I am pretty sure there is this thing that I thought everyone was AWARE OF called VOLUME which is togglable NOT only from the video interface itself called youtube BUT a MASTER VOLUME CONTROL VIA THE CONTRAPTION/DEVICE THE VIDEO IS BEING WATCHED ON HAS A VOLUME CONTROL FOR IT'S OWN OUTPUT BOTH OF WHICH ARE 100% CONTROLLABLE BY THE PERSON VIEWING THE CONTENT!!!! I mean really people? Are Y'all for real!? 🤯🤯🤯🤯🤯
@ragnardaviking1447 Жыл бұрын
Camera angle is so frustrating
@michaelpeterson3354 Жыл бұрын
Honestly, he’s breathing so hard I was worried he was going to keel over.
@2strokefanatic578 Жыл бұрын
lol if you think thats bad you should know sex with the wife is not easy for me too im getting to old, and i might have had a few too many hamburgers that time
@WisconsinEric Жыл бұрын
Interesting to see 2 piston rings, all the diagrams I looked at showed only 1 piston ring. Makes since as my Mantis seems to have far greater compression than my new Echo 2320T trimmer that has the same size 21.2cc Yamabiko engine, but only 1 piston ring. Good video sir
@gordonallenwoolumjr.6380 Жыл бұрын
Why don't you turn off the annoying music while we are trying to listen to you
@2strokefanatic578 Жыл бұрын
well sorry about that but unfornatly i have a very bad habit of listening to music, but dont worry i dont have any music in my videos anymore i been getting copyright strikes for the music so i had to mute the music but please enjoy my most recent fix it videos thank you for your comment
@StoneBarrington-jg3vu Жыл бұрын
Liked and appreciated the repair knowledge, comes in handy no matter who is in office. Thanks so much.😊
@BillBoulton Жыл бұрын
I'm going to look at your suggestions. The saw ran fine, then a couple of days later when I tried to start it, no spark. It IS on the second ignition module, I got lucky a few years ago and someone had one for $20 on the internet.
@2strokefanatic578 Жыл бұрын
hi there if this is a solid state ignition module where it does not have a capacitor and points that open and close its a very good idea to clean the fins on the chainsaw from wood chips and oil and to clean the parts where air comes in and is forced over the fins and ignition module to keep it cool good air circulation is needed to keep the saw and ignition moduale from being roasted by the heat of the chainsaw you may ask why well because in more modern ignition modules there is a capacitor and a tiny circuit board that run it all to make it spark yea i know very cool a beauty of micro circuity that goes into a fairly modern ignition module also look for bad ground on the saw and module and bad wiring good luck to you and dont forget to keep me on the happenings of your saw ok and like and subcribe and tell your freinds about me ok
@BillBoulton Жыл бұрын
Here's a long shot. My 400 evl ignition module quit (second one) on a saw I bought new. Any salvage ignition modules out there?
@2strokefanatic578 Жыл бұрын
Maybe look it up on ebay. You might find one on there also if I'm right that a ignition contact under the flywheel check for burned out contacts
@2strokefanatic578 Жыл бұрын
Also check the ignition cool for continuity if it went bad and it went bad or fried die to the heat
@2strokefanatic578 Жыл бұрын
Also it could be a bad switch too check it out look for bad grounds clean the wires oil is bad for the wires and it leads to bad wire connection check for proper air gap between the flywheel and ignition module if it's too large it won't create a spark. We'll I hope that helps out please be in touch if it works and if you need more help. Ok don't forget to subscribe and tell your friends about me and like my video it helps me out so other people can see my videos
@MrHighpressure Жыл бұрын
generally what is on ebay or amazon are generic carbs,,iwas hoping to get an oem carb
@2strokefanatic578 Жыл бұрын
you can go to oem replacemen t parts and look for your carb they usually have oem carbs on stock hope that helps
@MrHighpressure Жыл бұрын
Does that have a stock carb. If so can you tell the model number of the carb
@2strokefanatic578 Жыл бұрын
hi there mr high pressure this is a video thays 2 years old and i dont have it anymorebut i think it was a zama carb a rotary card thats wyz or something to that so maybe you can find it on ebay i found the carb gaskets on ebay so i think the carb should be there too
@MaddogsYardnFarm Жыл бұрын
When you take it completely apart like this, do you put it in a ultrasonic cleaner? Then apply lubrication to everything?
@2strokefanatic578 Жыл бұрын
on the big parts i like to clean it ib gas old gas if possible not want to waste new gas this will clean it good also cleaning the cooling fins so it cools better when running then assemble it all together with oil to pre lube the piston and other moving parts including the bearings in the rod and cylinder walls then assemble it together with high gas resistant gasket sealant this will make it leak proof also adding a drop of oil in the oil seals so it will not wear out quickly works all the time giving it 24 hours for the gasket sealant to dry hope that answers your question subscribe for more videos and tell your friends about me.
@2strokefanatic578 Жыл бұрын
o on the carb ill take it apart put it in a ultra sonic cleaner run it for an hour, i took out all the gaskets and diaphragms and moving parts then let it dry then reassemble.
@nmiklasz Жыл бұрын
I have a s620 that I just did a carb on, it runs but I got some Oil in spark plug how far do I gotta go for in for oil seal
@2strokefanatic578 Жыл бұрын
hello sir s 620 is a 2 stroke engine that has oil and gas mix it lubes the engines by going around the piston and other moving parts then going to the top of the cylinder to be ignited to run the engine so it would be normal if you have a bit of oil gas in the spark plug if you think you have to much try adjusting the high speed needle on the carb but also not enough gas oil mix will burn up the motor as for the oil seal you got one on each end of the crankshaft one end has the flywheel while the other end has the pully to turn over the paddles if in good working condition their should be no oil leaking from the crank, also the end of the motor should be free of leaks if not reseal that part remember 32 to 1 ratio on the gas oil mix not enough oil and you risk the engine burning up. but the s620 motor are super tough and long lasting with the correct oil gas mix
@abbowhunter5596 Жыл бұрын
I’ve done that same thing with the wrist pin retainer clip lol made a habit of trying to keep extras on hand in case one flies across the room
@gwp1ohio Жыл бұрын
need to get a mic...
@briannielsen7176 2 жыл бұрын
I took the fs45 apart to replace the on and off switch and I can't get the rod to turn. I made sure I slid it in the hole and it still doesn't turn. It turned before I took it apart to replace the on and off switch. Any ideas what I'm doing wrong. I love President Trump we had peace and prosperity when he ran the country.
@2strokefanatic578 2 жыл бұрын
sounds like something is jammed or one of the bolts is to long and is hitting the rod so it does not turn take apart and check all bolts there might be a long bolt thats holding it up
@bigboi9075 10 ай бұрын
Where the video rebuilding it
@MarkSWilliams27 2 жыл бұрын
Yep, Trump really made America great. By getting a bunch of brainwashed dummies to break into the Capitol, kill cops, and threaten to kill the Vice President, cause over 30 million dollars of property damage to the Capitol building, clog up the courts with a bunch of meritless lawsuits, continue to spread lies about the "stolen" election, and threaten election officials all over the country like some Mafia boss. SO great. He is a slicky, New York City flim-flam man who suckered all you dummies. Every single election official (R. and D.) in this entire country said there was no fraud. Every single computer expert, every single attorney except for that dress wearing Guiliani too. But no -- Trump knew he could do what he's done his entire life. Lie and steal to get what he wanted. Interesting how last election when Hitler Trump lost the popular vote, but won the electoral college vote -- well, that was just fine with him. BUT THIS TIME -- when he lost the popular vote by at least 7 million free and fair ballots? Well that was "fraud". So - he lied and continues to lie. And continues to sucker idiots who are weak in the head and believe that scam. He set you idiots up way back six months before the election by putting in your peabrain heads that he was incapable of losing the election. GUESS WHAT? HE'S A LOSER! GET OVER IT. Vote for him next time too if you want a country with a dictator. That's your right. But you have no right to make up shit. And ruin people's lives with harassment and extortion tactics.
@MarkSWilliams27 2 жыл бұрын
Trump is a criminal and part of the rich trying to kill off democracy. I won't rest until I see him and his criminal family in prison.
@lsperfect767 2 жыл бұрын
Nice video. Same problem can’t start. Replace head. And coil. Still no luck 🤨
@2strokefanatic578 2 жыл бұрын
check carb, bad rings not enough compression, also the gasket in the body between the cylinder head and main body id leaking so no gas oil air mix will go to the top, that my best guess good luck
@mikeharris2985 2 жыл бұрын
My tines stopped Rotating and won’t move will that be the worm gear or worm gear bearing or something else thank you
@2strokefanatic578 2 жыл бұрын
yes my guess the clutch is stuck closed or oil and dirt in clutch and clutch housing or you got a rock stuck between the tines and body you may not have seen it
@mjshuja1948 2 жыл бұрын
It is NICE TO HAVE CORDLESS IMPACT SCREW DEIVER✌️✌️✌️✌️👍👍👍👍👊👊👊
@2strokefanatic578 2 жыл бұрын
im going to have to get one in the near future but im a poor man ill have to wait
@XxBloggs 2 жыл бұрын
Can’t see a thing
@bobchandler5899 2 жыл бұрын
Does the mantis tiller have a shear pin in the flywhell?
@2strokefanatic578 2 жыл бұрын
the newer ones dont the shear pin is on the flywheel which sucks that you need to buy a new flywheel if you shear off the pin