superhogult

Пікірлер

@ryder2shae 16 күн бұрын

What year is that engine?

@bobwhite1734 6 ай бұрын

Could you show how you connected each individual lines to each cylinder?

@londondudley3492 8 ай бұрын

I have a ford 2000 tractor and after replacing the power steering cylinders both of them are bent now. Can anyone help me with the issue?

@Brian-ig8zx 11 ай бұрын

Do you fill the canister completely up with oil and what oil did you use?

@crowridge1 Жыл бұрын

Do you have a video where you re sealed the grinds of the power steering rods? And the kit parts order # ?

@mikeprice1816 Жыл бұрын

Good instructions man I got to put them seals in my 2000

@mikeburke8656 Жыл бұрын

Take 2x4 and cut into a wedge like a door jam. Then put that between the ball joint and clutch houseing. The wood won't damage the nut or threads and spread the pressure over a larger area.

@jballard-kk3xh Жыл бұрын

Really appreciate all your advise and the little things we didn’t think of! Very professional and visually clear. Thank you.

@chrisclayton5334 Жыл бұрын

If you take the 2 bolts out that hold the arm on, it makes the back part a whole lot easier. Loosen the nut just past threads on the tie rod end and tap with a brass hammer.

@henryparrott2447 Жыл бұрын

Great job thanks

@johnblanks2375 Жыл бұрын

Where to buy part’s for Power steering for a 3000 Ford tractor 1:21

@royross2426 2 жыл бұрын

i see this thread is quite old but looking for info on tearing down the steering gear box on the same tractor as you.....specifically removing the side plates in order to remove the steering sector gears not finding much info on this......

@ronvermeeren1347 2 жыл бұрын

Great explanation!!! Tnx

@MrBruce0777 2 жыл бұрын

Some really good tips thanks for the one on how to use a wrench behind the nut on removing the rear cylinder. I only had enough space to allow for a piece of flat stock . I got it nice and tight and beat it with a hammer later had to use ball joint fork tool to break it loose. Sweet thanks

@tedpeacock3945 2 жыл бұрын

I have a ford 2000 with the exact same system … works great turning left but when turning right the steering seems to bind …. However if I throttle up the tractor rpm’s then it will not bind … any ideas why that might be the case ?

@Dipstick252 2 жыл бұрын

Buy a tripod

@jeffsmith6270 2 жыл бұрын

Thanks very helpful

@johncarr5139 3 жыл бұрын

Can you provide part numbers? Especially for the the rubber bushings - my cnhi parts guy punted!

@abdulrahmansb2576 3 жыл бұрын

03107420045

@russellhancock9765 3 жыл бұрын

My Dad's Uncle bought Our 3000 Diesel a month or so before I was born in January of 1968. My Dad says that Ours doesn't have the 13mm bolt in the back of the pump like You are talking about. I know it is the original pump, because I know My Dad's Uncle rebuilt it with rubber washers like You put on House Facets with. I don't think if the older models had a different pump or what. I am thinking that it probably came from England because Diesel Tractors were pretty new back then.

@russellhancock9765 3 жыл бұрын

If You had glow plugs it would start nearly as good as a Gasoline Engine.

@russellhancock9765 3 жыл бұрын

It might Help My Dad and I soon. We Have a 1968 3000 Diesel almost like Yours and it does turn pretty good, but I think something is slightly out of line because it will only turn in one direction and it is like the Tractor nearly tried to run over the front wheel. My Brother-N-Law put a front end loader on it for a while and I don't think He put it back together exactly right.

@andrewmartin4258 3 жыл бұрын

Great videos. I had the pistons leaking in my 335 steering cylinders. they are pretty easy to disassemble and repair but you need to weld them back together. I made a video if anyone is interested. kzbin.info/www/bejne/iojXiI2la5dnkMk

@andrewmartin4258 4 жыл бұрын

Excellent video. You can disassemble the cylinder to replace the piston O-ring. I've posted a video of doing that. If you don't mind I'll post a link.

@matthewlewellen6516 3 жыл бұрын

where is the link?

@andrewmartin4258 3 жыл бұрын

@@matthewlewellen6516 It looks like the link may have been removed. Maybe it was improper for me to post it. I really don't know. The title is "Ford 335 Steering Cylinder Repair". kzbin.info/www/bejne/iojXiI2la5dnkMk

@gregbacon819 4 жыл бұрын

I just disassembled one of my steering cylinders. The hardest part was removing the white nylon seal spacer. It was stuck tight and had to pry it out slowly with picks and screwdrivers. It finally came out in two pieces.

@juddrobinson6762 4 жыл бұрын

Im lucky, my steering pump and entire system was good on my 3000 ford gas. I was wondrring if you had any idea how to adj PTO engaging lever. I have to near stop tractor to engage. It grinds terribley. Couldnt find any adjustment in IT book from TSC

@lynnmackenzie9501 3 жыл бұрын

Mite be your clutch setup

@josegaucin6007 4 жыл бұрын

I need a new supply line. Do you know the part number to that?

@superhogult 4 жыл бұрын

I will look and see if it has a part number tag on it. If not you will need to contact the ford, NH dealership for a part breakdown.

@josegaucin6007 4 жыл бұрын

Are the two lines power steering lines the same I’m looking to order new ones.

@superhogult 4 жыл бұрын

I do not believe so. I can check and let you know

@alicefroehlich9733 4 жыл бұрын

Way kind of power steering fluid do you use? Thanks

@mauromagnatta2932 4 жыл бұрын

Ciao, possiedo un trattore identico al tuo, sto revisionando tutto l impianto di sterzo, ma le guarnizioni dei cilindri idraulici non riesco a trovarle qui.... Potresti aiutarmi se hai qualche codice dei ricambi oppure i vecchi da poter darmi delle misure? Ti ringrazio tanto

@denzilsmith343 4 жыл бұрын

Thank you it helped me

@mongomay1 4 жыл бұрын

There might be a shaft seal on the engine/drive side of the pump that is leaking, it will leak into crank case. Might want to change that while you are apart.

@ferencbrown7090 4 жыл бұрын

you know that if your tractor has a Simms piston-type injection pump, there is a button on the stop lever if you push that in a cold start situation it will rev your tractor all the way and then back down just so you can start it easier in cold and I'm pretty sure the 3000 had an intake heater.

@superhogult 4 жыл бұрын

Ferenc Brown this tractor has a cav pump and no starting aids

@ferencbrown7090 4 жыл бұрын

that's too bad

@Largo5441 5 жыл бұрын

Injection pump Simms or Cav ?

@superhogult 5 жыл бұрын

Oto Lite, it is a CAV pump.

@walterbanta4775 5 жыл бұрын

Thank you for taking the time and for your patience. I have a 4000 series, but it should be similar. Unfortunately, I will likely have to pull and reseal the steering column too.

@richardwall4580 5 жыл бұрын

Awesome videos superhogult. My father-in-law has a 4100 with this same system. He has been bending cylinder rods for 2 yrs. Do you have any info on how to adjust the pump output pressure? And do you have a psi spec for this pumps output?

@haroldfredd6978 5 жыл бұрын

Do you have part numbers for the cylinder ram seals and what type of oil did you use?

@superhogult 5 жыл бұрын

Harold Fredd no sir the repair was done four years ago but any Ford newholland dealer should be able to pull it up. If I’m not mistaken it was power steering.

@gscatty 5 жыл бұрын

3:31 :) bout to do this on a 231 - looks identical. Thanks for the series!!

@scottmurrell3872 5 жыл бұрын

Common sense explanation of cylinder seal replacement. Thanks.

@gwenlazarus1471 5 жыл бұрын

Great video. I am a new tractor owner, 1984 Ford 2810. Your videos are a great help.

@hakimkhan7089 6 жыл бұрын

phone nambar dho

@thatswiss1385 6 жыл бұрын

Crank longer and the engine will start at the first time😋

@superhogult 6 жыл бұрын

I have to let the starter stop or it just spins when The engine starts to hit.

@thatswiss1385 6 жыл бұрын

@@superhogult okay, intressting to hear!

@marcinsujkowski7734 6 жыл бұрын

Sorry forgot to add.. i really like the videos. very detailed and well done :)

@marcinsujkowski7734 6 жыл бұрын

i just inherited a Ford 2000. One of the steering cylinders leaks really bad. I ordered a seal kit and will try to replace them like you did. One question i had was regarding the "bleeding" you did in part 4. i'm a little fuzzy about what that means. Is all that is involved is having the reservoir open and turning the wheels really slow?

@superhogult 6 жыл бұрын

Marcin Sujkowski yes you will be moving the steering from stop to stop slowly to remove all the air from the system just as you would do a car. Just make sure it’s up on a jack or block to make it easier on you and your tractor. You will make a slight 5 second pause at each stop. Cycle through about 6 times and recked the fluid. Try not to let it get low as it will bring air back into the system.

@collinwheeler7999 5 жыл бұрын

Do these type of systems have a pressure relief on the column or the pump? Mine gets hot and hard to steer when the front end has a load on it. I just changed the fluid and did not help. Any info Would be greatly appreciated!

@kenrauch4701 6 жыл бұрын

I have a 3400 Ford that the steering turns left but does not want to come back to center , turns right fine and back to center fine , Any suggestion as to the problem ?

@superhogult 6 жыл бұрын

Ken Rauch I would lift the front of the tractor up as to get a better idea of what’s causing the binding. If you don’t see any obvious issues then remove the power steering cylinder to you can check the front axle for sticking I’m not sure what it’s called on a farm tractor but on a road tractor they are called the king pins. If no issues are found when the tires are turned left to right then I would suspect the power steering. If that’s the case add one cylinder back and recheck. If you remove the front of both cylinders and let them hang and watch them move while you turn the wheel and see if they match in movement

@mathewwahl8592 6 жыл бұрын

I have to replace the power steering pump on a ford 7000 series diesel tractor. Are the bolts to remove the pump behind the filter? Also it looks to run off the cam shaft gear, is the power steering pump gear have to be timed with everything else or not???

@advancednutritioninc908 6 жыл бұрын

I am just about to buy a Ford 3000 ... I appreciate your videos! Thank You!

@jorg4u1 6 жыл бұрын

I'm having the same problem with my ford 2000 cylinder seals are leaking.how did you press the seals?

@hommittens4165 6 жыл бұрын

How its shootin 2 at a time?????

@superhogult 5 жыл бұрын

Hom Mittens I’m not sure how but I ended up getting rid of it as It was useless like this. It was factory out of the box like this

@rlneal100 7 жыл бұрын

Did you replace the O-ring for the power steering canister? If so did it come with the filter kit?

Ең жақсы KZbin

Пікірлер