What if the pressure gauge does not have the venting cap?

What is the other way of fixing a gauge that is way off?

Awesome video! This was very helpful, thank you!

Can this be done with a pressure gauge needle dial that doesn't have a screw and needs to be gripped and popped off with a pair of pliers and then pressed back on?

Great Job, I was able to fix my gauge and reset it to zero

Good

How can i refill my gauge

TIA, got a used trailer with the same guage installed on trailer tandems. Facing problem to take the reading. Whats d right way to scale weight reading.

Everything was working fine . I just stoped running

My gauge is at zero, new pressure switch drained tank . I took air pressure down to 15 psi new pressure regulator switch 30-50 I put 27 psi in tank and I’m at zero pressure

How do you calibrate the small one at the end of the video? Mine does not stay on zero after I dropped it.

Remaining step need to be verified by recalibrate

Dude.. you have to learn protocol on making "how to" videos".. your 3min 8 sec video..way too ling.. you talked fir 2/3 of it... 2min 5 sec before you even started burping of gauge..life is short.. nothing you said helped anyone.. we came to find burping.. so either only provide what you promised.. or lBel video."me ranting nonsense for 2min. 5 sec..then I burp gauge" so we can forward you listening to yourself😊

I have a watter pressure gauge and the needle jumped some how behind the zero pin. How can I move it back over the pin?

Hi: I have a general question regarding gauge design: On some of my dial-type tire pressure gauges, the pointer rests against a stop(fully left or zero), and my others, the pointer simply resides in a zero 'box' or zone when it is reset, or not measuring anything. What are the advantages and disadvantages to either zero design, aaaand: does it matter that much where the needle rests inside the zero box on gauges without the zero rest?

2:45

BURP! Ahh.....thats better.

In doing this, if the bourdon tube has had some excessive wear, you will need to recalibrate the gauge so that it reads accurately. To do this, you will need a pressure gauge comparator and a digital pressure gauge. Doing what is demonstrated in the video will only reset the zero. Keep this in mind.

The guage reading won't actually be wrong, it's equal to the conditions it was set up in, so for most guages that'd be sea level pressure at most likely 20-25°c. I'm only splitting hairs in this comment, I don't mean to say anything about burping is wrong because it's all about the relative differential pressures.

Nice information!

I burped mine and it didn't move

Pantek ang

Any tutorial where it says “you might damage it and buy a new one” is a shit tutorial, so you get dislike for this one

How to remove glass

i did this with my guage and its still stuck at 5 psi

its lovely

A pressure gauge like that should be sent to a calibration shop for accurate calibration.

This actually fixed my gauge! Thank you so much.

Thanks for information

Fantastically explained. Thank you!

got a question for you i got a liguid gauge 0 to 60 and i got a 1990 k5 blazer got my engine rebuld i did some up grades and some mods to mt tbi so i need the gauge to set my regulator pressure and i got some to burn my chip i put bigger cam in it ..my gauge were reading 10 psi with the stock spring and i try to adjust it but it stay at 10psi so i were thinking maybe the spring were weak so i put in a 18psi spring when i frist put it in with no adjustment it was reading 10 psi ..so i started to adjust it and it went to 20 psi i were trying to get it to go to 14 psi so when i back off it the screw is not even touching it and it is still at 20 psi it as if it is sticking ..and when unscrew the gauge it dont drop down to 0 and it should what do you think

Hi I bought my pressure gauge a few months ago and now I noticed that it's leaking from the bottom. Is it time for a new one? Or is this common?

What else you got?

Do I need to burp a new gauge if it's already at 0?

I have a question I need a oil pump pressure gauge minimum 150 PSI It also has to be engaged that I can use with diesel gas oil kerosene do I need to buy what's called a combo pressure gauge I want to make my own I know I need a high pressure hose and that was my other question when I make the hose up I need a 300 PSI hose hydraulic hose what kind?

❤️❤️❤️👍👍👍

thanks boss

Nice

How to fix a dry guage?

Is it use metal diaphragm? we are the supplier of the metal diaphragm

If you have the version with the brass fitting accidentally being pulled out too far, how do you reset it as it’s fallen below zero?

Thanks 👍🏻

GOOD

Wow bitchn! Thanks:)

can liquid filled gauges be used horizontally?

What if my gauge is moving down even im not using the water.

What are you doing when the gauge is that zero and then you’re starting to tighten it up on the bottom and then the gauge goes up?

please what is angularity error and can it be fixed?

Why atmospheric pressure is not shown by pressure gauge in the rest

hi - do i pierce it and make a small hole in it like it says on the instructions ?