crazyskullcrusha

Пікірлер

@farrider3339 2 ай бұрын

Perfect job. How I like that quicksilver o meter 😍

@ErnestHaymer 4 ай бұрын

I like car

@ErnestHaymer 4 ай бұрын

I like car

@ErnestHaymer 4 ай бұрын

I like car

@ErnestHaymer 4 ай бұрын

I like car

@kitchenbriks3685 4 ай бұрын

Soapy water is the way to go with tamiya decals. Going on dry is impossible

@GENX80. 4 ай бұрын

Any noticeable performance issues?or just shorter and louder pretty much it

@sneetchy 8 ай бұрын

Solid tip on the servo horn. Stock setup was surprisingly bad, and I just didn't want to commit the time and effort to the dual servo mod. This was a great middle ground. Nice one.

@joebushell2438 8 ай бұрын

So i must ask ,its been over 6 yrs since install ,have you had any leaks or issues

@gregkoe60 Жыл бұрын

Sounded nice riding off at the end..

@at7045 Жыл бұрын

Question with your 3 way switch that you use to turn on your accessories are you tripping a relay in the one position and then using a keyed ignition wire in the second position? I looked at your videos and dont see wiring howto.

@twerdt6071 Жыл бұрын

How much do you charge? Got a gsxr k5 same exhaust. Looking to get it done

@flyingfortressrc1794 Жыл бұрын

Great ideas. I'm going to have to try this on the Clod Buster I'm currently building. Thanks 👍

@blkbeard4554 Жыл бұрын

Thanks for sharing. Did I see a small Axe Mounted on the inside of your box you didn't mention? if yes how did you mount it? ( I say never go in the Bush without an Axe.) Time for a part 5? /6?

@y.g.smokedog3233 Жыл бұрын

Bruh you did a great job on rewiring the whole car... 👍

@escobar-rc-sinnerz7108 Жыл бұрын

Nice clod

@IowaBudgetRCBashers 2 жыл бұрын

Great tip on the steering

@brapptv44 2 жыл бұрын

did you get the v2 head or just the cylinder? if so how is it wwith just the cylinder?

@crazyskullcrusha 2 жыл бұрын

Just the cylinder and carb. Has too much power with the cylinder alone.

@tylermoore6574 2 жыл бұрын

though the video is old, you've convinced me on getting a shorter bar & chain. thanks man. great info.

@quenemoend 2 жыл бұрын

Way too much about ancillary issues. Searching for sawing off and exhaust and I get this long drawn out thing so it might be a great video for some things but you need to get to the point faster.

@crazyskullcrusha 2 жыл бұрын

Then grab your hacksaw and cut it off you fucking idiot 🤣

@CHIBA280CRV 2 жыл бұрын

Fantastic job ,look and sound on the yoshi 👍👍👍👍👍

@RCRoads 2 жыл бұрын

Great idea putting pads on your body. The less the body moves around on the post the better. Great video and awesome truck.

@politicalfoolsandhorses 2 жыл бұрын

Take note that as soon as you take a ANY speaker out of it box i.e. without at least a baffle - the sound changes to miserable! I used the front end of the boat - closed it with three ply - mounted the speaker inside it (you have to cut a round hole of course and screw the speaker o the plywood) - and the sound is far far more solid, robust and louder too - it is in fact stunning, far more close to how the engine would sound.

@bmker5469 2 жыл бұрын

Good neat job.. just about to cut 5 inches off my Remus pipe on my K1300s. Hope it goes as smoothly as the Yoshi.

@AuProspecting-Scotland 2 жыл бұрын

that does look great shortened, i'm thinking now its shorten and closer to the tyre rubber, is it possible to spray tyre with exhaust smoke at traffic lights etc

@cluke50 2 жыл бұрын

Could you please post a video of how the front cylinders are in the upper control arm? Did you weld a plate over the opening with a hole for the cylinder?

@coleman6131 2 жыл бұрын

Does that have the original ST-300 trans? I have that same car and am thinking of putting a THM350 in it.

@crazyskullcrusha 2 жыл бұрын

Mine has a TH-2004R. It's nice cuz it has overdrive. A 350 or 400 is only going to be a three speed no overdrive.

@GasGunsGod 2 жыл бұрын

This video was great until you put the yoshi tag back on...

@robinrouter2059 2 жыл бұрын

lifter preload is very important for solid lifter cams...hydraulic cams not so much...imo ....a bent rocker shaft can really screw up the engine timing!!

@건프라빌드-v1k 2 жыл бұрын

wow amazing very good cool 👍👍👏👏😎💯

@matsfredsson9445 2 жыл бұрын

Yes, clutch slip is standard. I put stronger springs in my S2, works perfect! The most fun start above 4500 rpm....

@MavAuto-Pete 2 жыл бұрын

I've sprayed mine matte blue with custom pained black grille edges. Hobbywing esc 2x tamiya brushless motors.

@henrysjoblom4917 2 жыл бұрын

What happened to your cr80 build?

@tylerwatt7697 2 жыл бұрын

wow 5-600 for the radio, just get a deck an amp and some 10s used lol

@tylerwatt7697 2 жыл бұрын

also toggle switches are cooler, them rockers are safety certified blah blah blah

@Hudson12339 2 жыл бұрын

Did you work out the starting issue?

@Hudson12339 2 жыл бұрын

You did a very good job on this Series!

@toddnewman2680 2 жыл бұрын

Great video! We have a 05 KLX110 and my son wants more power, esp bottom end. Is a big bore kit worth it or should we just go with a Pirahna 140 for $2300? Thanks

@haroldwilson1485 2 жыл бұрын

Looks like you got your hands full great project good luck bro!

@bmonkey14 2 жыл бұрын

What size carb did you running before ? Any updates ?

@Cadillaclife2023 2 жыл бұрын

Any updates on this?

@alanpassmore2275 2 жыл бұрын

Hi I just fitted the police light bar on mine in between the on off switch and the Speedo once I drive I think the light gets to much power do I need a resistor fitted ?