5W Productions

Пікірлер

@DipajcDipa 23 күн бұрын

thanks for your sharing

@koomencontracting Ай бұрын

Those smaller machines surprise me every time 💪🏻 🔥

@davismarrero4179 7 ай бұрын

I'm just here for the comments

@ethanhobbs10 7 ай бұрын

Dude your the best our case ih 100c did this and that fixed it

@simonwhittaker4872 Жыл бұрын

Thank you very much for posting this, it was exactly the cure I needed and worked exactly as you stated. Now if you only had a cure for the tractor dropping to 1500 rpm every time I used it! Thanks again for taking the time to help others.

@simonwhittaker4872 Жыл бұрын

Just to add clarity, this worked for me on a Workmaster 75.

@sigepserb 2 жыл бұрын

Same problem it fixed it thanks

@simplerenovationtips 2 жыл бұрын

I have done a similar job with a gloss laminate countertop and the result was amazing. I have a video of it on my channel

@harryballsacky 3 жыл бұрын

KEEP YOUR DAY JOB,

@dustyspicher5430 3 жыл бұрын

I have a t4.75 with 300 hrs. Its been down for 6 months. Still under warranty but new holland will not stand behind them. The engine needs software. No repairs in site at this time. Junk tractor. Buyer beware. Junk..

@alegator7249 3 жыл бұрын

And if want to see more videos of Lowes subcontractors; hit the subscribe button

@jrob738 4 жыл бұрын

I appreciate the tip for those that don’t have “proper” tools for this. Anything is better than having these flaps sticking out on my edges.

@centralcoastcamper9631 4 жыл бұрын

Some Farrier is looking for his file!

@alexlongfield2113 4 жыл бұрын

Bruh, is that a rasp you got there????

@gracie7257 4 жыл бұрын

Thats F up..

@moatley4218 4 жыл бұрын

Troll level 9,000!

@LTDan-hu5fq 4 жыл бұрын

This guy has no skill or knowledge at all, he needs to watch more videos before he makes one.

@pipedreams57 5 жыл бұрын

That is not a file you are using. It is a coarse/fine grade wood rasp, not the right tool for that job. A 4 inch grinder with sanding disc or even a drill with a sanding disc would work much better, then a fine, single cut flat file to finish it off.

@Duckywucky92 5 жыл бұрын

And he is still filing to this day, half the cabinets are left

@glennlienhop342 5 жыл бұрын

It's almost like trying to escape from Alcatraz But not as tedious Lol

@matthewcandelaria4128 5 жыл бұрын

Have that problem at this moment. Thanks for video. Little nervous bout pulling on it that hard but here it goes

@robertnorman7703 5 жыл бұрын

I only have 135 hours on mine and it did the same thing, only mine wont un stick. Don't even know if I can trailer it without dropping the bucket, because of how low its stuck

@csanchez91766 5 жыл бұрын

WTF!!!!!!

@imranibnismail 6 жыл бұрын

Don't listen to these morons. Thanks for the tip. You should try to use a finer file to give it a nice finish.

@Ujeb08 6 жыл бұрын

the internet is just full of experts who need to be teaching us!

@dnsmithnc 6 жыл бұрын

You can do a good job with a file for small jobs like this but the big problem is that he is trying to do this while holding the camera. And it looks like he placed the edging to high on the top necessitating more trim work.