De stoom kleppen zijn net niet goed afgesteld! Vandaar dat tikkende geluid! Verder is het een erg mooie stoommachine!👍
@TH-wj9ty24 күн бұрын
?? The engine runs smoothly on the original settings. Slightly clunking sound rather due to worn bearings - after 120years...
@superkip592024 күн бұрын
@@TH-wj9tydat is ook goed mogelijk!
@ashj_2088Ай бұрын
Boil the kettle and fill it with hot water so it doesn't take all day to warm up🍻😋
@Be-GreifenАй бұрын
Und so leise 😊
@Be-GreifenАй бұрын
Muss das am Kessel lecken oder gibt es kein Überdruckventil?
@TH-wj9tyАй бұрын
Sicherheitsventil vorhanden und funktioniert. Lange her, war ein Testlauf, zeigte Undichtigkeiten an mehreren Stellen.Das Glas im Wasserstand ist inzwischen abgedichtet.
@Be-GreifenАй бұрын
@@TH-wj9ty Geile Teile! Tolle Technik.
@Be-GreifenАй бұрын
❤
@juergen.hamersАй бұрын
Schön, die Maschine laufen zu sehen. Läuft prima.
@brucerogermorgan2388Ай бұрын
Interesting valve arrangement, works very well.
@brassandbricks77012 ай бұрын
Interesting valve design!
@TH-wj9ty2 ай бұрын
Right, thank you. Quite hard to find. Bing used a similar poppet-valve gear, but with spring coils for each valve.The Doll valve-models are far more sophisticated - but for some versions the valve gear is fake...
@txlabmansteamtoysmore49802 ай бұрын
Nice job getting this one running! 🤠
@TH-wj9ty2 ай бұрын
Thank you! It still needs some adjustments, now that I have tightened the cylinder screws I must also shorten the one holding the cylinder front cover...
@b43xoit4 ай бұрын
I had the rocker type; it could not be reversed.
@TH-wj9ty4 ай бұрын
Do you mean the rod-/slide-valve version? Both versions cannot be reversed (which can easily be achieved by mounting the drive belt in a "lying-eight" fashion for running accessories). Thanks for your comment! In my channel you find a video where it is driving a Doll Hammer!
@MarttiSuomivuori4 ай бұрын
My father built me a steam engine when I was 6.
@wetleyrocks30924 ай бұрын
What a wonderful engine! I saw the link and thought it was some sort of Mamod from the 70's (SE1a for example) because that's what I saw my grandfather using with my elder brother (OK, I was jealous!) But look at the mechanics on this beauty! I never envisaged that you could get cams and bevel drives... Great post 😀
@TH-wj9ty4 ай бұрын
Thank you, my pleasure!
@TH-wj9ty5 ай бұрын
I was notified about a comment, which I don't find here? Well, yes this engine was produced by J. Schoenner, Nürnberg. Here the version sold by "Dr Oscar Schneiders Lehr-Mittel-Anstalt", actually a Leipzig based retailer or mail order service. "Lipsia" is the latinized form of "Leipzig", btw.
@Modelsteam-jw4wk5 ай бұрын
Beautiful engine I wish I could obtain one but they are extremely rare to find in the states
@Calin10005 ай бұрын
Runs beautifully!
@TH-wj9ty5 ай бұрын
Thank you. Camshaft wobbles slightly but who wouldn't after 110years.
@SmithsMuseum7 ай бұрын
I don't speak this language but that shit looks cool
@TH-wj9ty7 ай бұрын
Doll & Co portable overtype steam engine model No 502/1 (the smallest) about 1927 and thresher model by unknown maker, sold by "K. Fischl" toy emporium, Prague, before WWI.... ;-)
@AcerxHDP7 ай бұрын
Esta gooddd 🎉🎉🎉
@Steam-Buddy7 ай бұрын
Ich mag die landwirtschaftlichen Antriebsmodelle von Doll. Danke für das Video.
@TH-wj9ty7 ай бұрын
Die Lokomobile ist sicher von Doll, die Dreschmaschine nicht. Trotz des Firmenzeichens (Kinschel? Knischl?) keine Info zum Hersteller bisher.
@Steam-Buddy7 ай бұрын
@@TH-wj9ty Danke für die Info.
@olivvapor48738 ай бұрын
Cool video Thomas ! 😊 Thanks for sharing !
@TH-wj9ty8 ай бұрын
The only mistake was taking a cork block as base for the hammer. Muffled the noise = half the fun ;-)
@olivvapor48738 ай бұрын
@@TH-wj9ty 😅
@Dark_Matter28 ай бұрын
Is this model of real machine?
@TH-wj9ty8 ай бұрын
I don't think so!
@kensutherland4148 ай бұрын
I think you need the rocker/ lever to be beam type to transfer force up and over the and strengthen the lower of the rocker joint and the upper of spindle bearing and lower structure and you could press button studs with it. Really nice unit. Well done.
@TH-wj9ty8 ай бұрын
High Ken, the BSL hammer is not a masterpiece of German engineering, I am happy I succeeded in getting it moving quite smoothly (long story why this company making screws suddenly started meddling in the toy steam business). Have you seen the Sachsenmeister hammer in the other vid I posted? That's a cute thing - it's pneumatic!
@boredincan8 ай бұрын
I don't know why this has been suggested, but it seems like a very neat little steam engine powering a TINY hammer. Lots of rotation for not many stamps of the hammer, I'm assuming there's a power transfer, and you could flatten fingers, coins, very small rocks with the hammer.
@TH-wj9ty8 ай бұрын
Right, this was just a first test run of the engine after a thorough overhaul. The BSL hammer (very rare product from the GDR/DDR) has been overhauled as well, so I took the opportunity to see if it works at all. There is a lot of inertia in the system... Will try again with better transmission...
@Steam-Buddy8 ай бұрын
Tolle Maschine!
@TH-wj9ty8 ай бұрын
Danke. Recht selten.
@octovid10 ай бұрын
Isn't it steyr?
@TH-wj9ty10 ай бұрын
No, this is the Carl Steyer company, located in Freiberg, Saxony. The steam accessories were produced in the 1950s, in DDR/GDR times.
@octovid10 ай бұрын
@@TH-wj9ty Ahh well. Good to know, thank you.
@maximeestevn531910 ай бұрын
Do not let the ants see this we do not need them entering an Industrial Revolution
@jeanlucfaille7495 Жыл бұрын
Nice !!!
@TH-wj9ty Жыл бұрын
Merci!
@juergen.hamers Жыл бұрын
Der Arbeiter am Schleifstein hat am Ende des Tages sein Brot verdient.👍 Ein tolles Modell!
@TH-wj9ty Жыл бұрын
Danke, Jürgen.Der macht mir auch richtig Spaß! Nur der Knoten im Transmissionsriemen ist noch zu dick...
@TH-wj9ty Жыл бұрын
Der macht mir auch viel Vergnügen!
@Metaconta Жыл бұрын
Muy bien. Very good. ;)
@TH-wj9ty Жыл бұрын
Nope, live steam. You can see the blue-ist flame of the burner under the boiler. Sorry for the bad quality of the video!
@soldado2112 Жыл бұрын
¿clockwork?
@sunimalpiyarathna3518 Жыл бұрын
Nice work
@dampftim7390 Жыл бұрын
Schöner Fallhammer.👍
@TH-wj9ty Жыл бұрын
Leider etwas übermalt. Aber danke!
@Steam-Buddy Жыл бұрын
Beeindruckendes Modell!
@Terrys-Steam-and-Bricks Жыл бұрын
I love all the action.
@Terrys-Steam-and-Bricks Жыл бұрын
Fun!
@Terrys-Steam-and-Bricks Жыл бұрын
Beautiful engine!
@dampftim7390 Жыл бұрын
Danke für die guten Vorführungen.
@TH-wj9ty Жыл бұрын
My pleasure ;-)
@TH-wj9ty Жыл бұрын
"Cool" ist natürlich ein netter Kommentar für eine Hundertjährige, die 100° heiß ist ;-) Aber ich danke Dir! Vorher sah sie sehr schrottig aus...
@skeptic49 Жыл бұрын
really nice Carette
@scorpion2nz Жыл бұрын
A twin and reversing and and a feedpump . What more could one ask for .
@TH-wj9ty Жыл бұрын
Well, and a 9cm boiler for good measure... :-)
@dampftim7390 Жыл бұрын
Schöne Maschine mit sehr interessanter Speisepumpe.
@TH-wj9ty Жыл бұрын
Die Speisepumpe ist das "normale" Carette Modell, aber der Antrieb über den "Kniehebel" direkt von der Kolbenstange her ist wirklich sehr ungewöhnlich. Aufgrund der vielen Kräfte durch Pumpe und Ventil-Umsteuerung, verdreht sich die Kolbenstange... Vor der Restaurierung war die Pumpe lose auf der Grundplatte und gab die Kräfte an das Kesselhaus weiter...
@petrikokko1441 Жыл бұрын
A pleasure to see.
@TH-wj9ty Жыл бұрын
Thank you, Petrie. A twin with the double reversing gear is a rather rare sight...
@petrikokko1441 Жыл бұрын
Nobility of steam.
@TH-wj9ty Жыл бұрын
You've put it in a nutshell, thank you!
@TH-wj9ty2 жыл бұрын
In der Tat nicht. Die 4-Zyl.-Schiffsmaschine von Sachsenmeister daneben ist auch noch gelaufen, leider in der Hektik ohne Video, die sieht man noch seltener.
@dampftim73902 жыл бұрын
Wow, das sieht man echt nicht oft.
@dampftim73902 жыл бұрын
Eine schöne Maschine.👍
@TH-wj9ty2 жыл бұрын
Danke, sie braucht noch ein bisschen Pflege. Interessant ist die vereinfachte Anpressvorrichtung für den Ventilschieber (ohne Kugel...)
@dampftim73902 жыл бұрын
Was eine Wunderschöne Maschine. Noch nie gesehen.
@TH-wj9ty2 жыл бұрын
Ja, dieser "Pseudo-Schiffsdiesel" ist ein außergewöhnliches Teil. Der Wasserstand war übrigens mit Kleber "repariert", jetzt ist ein passendes Originalteil drin. Diese Maschine gibt's noch in einer größeren und aufwändigeren Version!
@Jckebua2 жыл бұрын
Klasse Teil ! Die hab ich auch in top restauriert . Danke fürs zeigen ! :-) Ich liebe Schiffsdampfmaschinen !
@TH-wj9ty2 жыл бұрын
Der Lack auf der Bodenplatte sieht nicht mehr gut aus, aber immer noch besser als schlecht nachgemalt. Wenn Du Schiffsdampfmaschinen liebst, müsste Dir meine Sachsenmeister 4-Zylinder gefallen...
@komtasu3 жыл бұрын
very nice engine.
@calypso223 жыл бұрын
What happened?
@TH-wj9ty3 жыл бұрын
Oh well, just wanted to show that this centenarian still has some "compression" (main valve closed)... Meanwhile you can find videos with this engine running well under steam!