Please can someone tell me what program or application this is? I live in Brazil and I liked the format of the videos and I want to learn about it to apply in my business.
@CalhasPrecobom Жыл бұрын
Please can someone tell me what program or application this is? I live in Brazil and I liked the format of the videos and I want to learn about it to apply in my business.
@jecilopjp4806 Жыл бұрын
With the side flashing and the endwall flashing on top of it, what is the required height allowance to install this roof system either from the top of the ribs or from whatever deck system is used whether purlin or osb? The flashing height requirements is what I cannot find. I have a VERY tight fit with a porch roof design under transom windows and need to know what I can work with. This would be a traditional finish (no counterflash or reglet), so I just care what happens with the height requirements on the endwall to do the flashing.
@azucenaesquivel5631 Жыл бұрын
What is your opinion about foam closures ??
@cgmwoodworx2 жыл бұрын
i want to see this process done with existing vertical steel wall. i have plans on doing an addition on my current 40x40x14 garage and would love to see the process. there isnt very many, if any videos of doing this install on vertical metal correctly.
@eastside04342 жыл бұрын
Why didnt you double caulk, end wall flashing and then caulk the counter flashing,one will eventually fail.
@ericcajo3 жыл бұрын
How wide is the ridge ventilation space between the plywood?
@richardhertzdonut99473 жыл бұрын
What tool do you recommend for hemming the edges?
@eslamsaad35583 жыл бұрын
Great work , which software you used to make this animation , thanks
@retiredlogman3 жыл бұрын
After watching your videos I now realize that your design has much more thought put into it. I wish I would have known about you 30 years ago.
@edstransitscott91863 жыл бұрын
Beautiful job,
@micahboak2203 жыл бұрын
Thank you for showing this... very helpful
@adsensepincode66514 жыл бұрын
Good roof
@uditbhardwaj37224 жыл бұрын
What if i want to insert a polycarbonate sheet in between these panels. how to insulate that?
@russelldodd934 жыл бұрын
Thank you.
@rafaszafran31474 жыл бұрын
Kocham te filmiki wszystko pieknie cudnie na animacji w rzeczywistosci nic wspolnego z realem
@juliusgabayan76714 жыл бұрын
Is it a rubber when you put an outside closure?
@lynnroberts6716 Жыл бұрын
The cloures are foam. No rubber.
@japansh4 жыл бұрын
Who is the manufacturer of this perforated cleat? I checked UnionCorrugating web site and couldn't see the cleat. Any information is highly appreciated, thanks.
@Manfran3 жыл бұрын
Great video! But my Standing Seam roof only came with the z closures and no perforated clear. Now I am confused on if I need the perforated clear or if I can cherry max the ridge cap directly to the Z closure
@vipahman3 жыл бұрын
@@Manfran If you have a ridge vent, you should get perforated panels. Otherwise the venting dead ends at the ridge and is useless.
@Manfran3 жыл бұрын
@@vipahman thank you!!
@matt894475 жыл бұрын
I need to butt two roofs together adding a valley underlayment of a 20' (creased) piece. I'm installing a carport under the lip of my Butler garage down to my other garage roof. Otherwise I need to raise carport roof above lower roof allowing water to then drain onto garage roof to be collected by the gutter and removed. Butting them seem to be better to me and allowing the Valley piece to allow water to flow towards back of garage. I'll be re-roofing the garage with metal as well. Will this be ok?
@gman49375 жыл бұрын
I love these videos, thanks for putting them out. My question: Do the screws holding the z channel cause distortion in the panels? I've always heard that standing seam roofs are superior because they are fastened with clips to allow the steel to expand and contract independently of the wood structure. Thanks again.
@Logan-rk5kd5 жыл бұрын
Awesome videos! Does anybody know how to build a roof with a hemmed rack and endwall flashing? I'm not seeing a clean way to integrate the two.
@libertariantranslator19295 жыл бұрын
Beware instructions that tell you to pay attention to the tape measure rather than where there is decking for the screws to bite into. But the graphics are nice.
@orlandomaldonado42555 жыл бұрын
😎
@davidhook4875 жыл бұрын
Thanks so much for the videos! They have helped me on over 5 metal roofs! You guys are a blessing! Keep them coming!
@checkmate50025 жыл бұрын
I assume the screws need to go into wood on the other side of hte metal. Ie plywoood and not purlins. How do you secure it is the roof is sitting on purlins?
@makeiteasy57735 жыл бұрын
Ese sistema no es seguro.
@maryparson36844 жыл бұрын
Envíe uno más seguro
@brendalanham725 жыл бұрын
I I Installing radiant foil I
@grayprincess565 жыл бұрын
No wonder the porch roof leaks. Shade tree installation. Will take it all off and, with this knowledge, we will do it over ourselves. THANK YOU!
@danielkoehn32095 жыл бұрын
Very good explanation!
@adamd72165 жыл бұрын
I'm wondering if you have a video on how to join two ridge caps running perpendicular to each other?
@chadapol80565 жыл бұрын
Hey Great Video! I was wondering if the standing seam metal has to be perfectly flush around the sides and bottom of the chimney? It seems to me that 28 seconds, as long as the z - trim can be installed on the metal, then it is ok if there isn't metal all the way to the chimney because it will be covered and waterproofed by the flashing. Am I correct in thinking this?
@metalguyn5 жыл бұрын
Perfect thank you!
@FloridaFrank20105 жыл бұрын
This is great! You guys should make these panels available as special order from our local big bx stores maybe? (e.g - Lowes and HomeDepot)
@jasonthurston7995 жыл бұрын
Side of the roof that the panels started from work out nicely but often the opposite side doesn't have a flat section of the corrugation in the right place to seat the rake. What do you do then?
@paulschimpf81215 жыл бұрын
How about a little help figuring out how to make those cuts? Especially the triangular one at the peak.
@1weirddoe5715 жыл бұрын
Kick out bend-- please show how for siding.
@joelposhusta77466 жыл бұрын
All looks good with the video except for bending of a lengthy rake edge. I am proposing to make 1 inch cuts every18 inches along the rake to allow a sequence of18 inch bends (assuming 18 inch bending tool). Maybe make 1/8 inch hole punches to end each cut. Replies welcome.
@hopenavajo13916 жыл бұрын
Are the hole already predrilled.
@backfireguitarz6 жыл бұрын
What do you do if the rib of the last panel is not under the gable trim?What do you do if the rib of the last panel is located under the leg of the gable trim?
@macster14576 жыл бұрын
so what is the last panel holding on to?.. are there any screws holding it?
@jsnthurst16 жыл бұрын
What if the sidewall flashing's doesn't end up on a flat bottom part of the panel where the butyl tape is, like what if it is partially on a hump? I realize that one would try to start the panel against the wall to make it work out properly but that might not always be possible, like if you are going between two sidewalls.
@joellubell6 жыл бұрын
How do you finish off the top of the valley? it seems to me the way the trim is left in the video that water will get in between at the gap at the ridge. There are no videos showing how a ridge cap would finish that off.
@ericschaefer27296 жыл бұрын
Who does all your animations and what program do you use? Very nice work!!
@alikockaya766 жыл бұрын
Whoever made these super high quality animations, my hat's off to you. This is some high level, high effort work! Very well done!
@joshneff85326 жыл бұрын
so I have a commercial metal roof and the previous owner added on and the profile is different so i get leaks. they overlayed it about 6 feet but water still comes in. Can you help me please!?!?!?!?
@SBarone25256 жыл бұрын
Best video for flashing ive seen thank you!
@teamtunell6 жыл бұрын
I too love these videos. This one has a potential problem, though, where the two valleys meet at the top. It is shown with a small gap between the valley panels. Is there a way to join the two valleys elegantly?