Пікірлер
@darvish036 49 минут бұрын
What was the problem and how did you fix?
@Grumpyoldmechanic-l3r 6 минут бұрын
We just put a used transmission in. Fluid level was fine. I am assuming the main pump in the transmission went bad
@Sakib234-s2o 8 күн бұрын
Hello, "Grumpy old mechanic" I was analyzing your channel and saw that in your channel have some problem, That's why your channel is not much growing and not getting much engagement, If you can solve these problems, Your channel will grow like a storm. If you tell I can tell these problems. Where can I tell? Here or ig or where?
@Grumpyoldmechanic-l3r 8 күн бұрын
No
@kanishaburwell7548 15 күн бұрын
How the heck do you position yourself to be able to see where the screws are
@Grumpyoldmechanic-l3r 14 күн бұрын
lol. I am so use to it I could. But if you put your phone on forward camera you can use it as sort of a mirror
@HeydaCarreras 17 күн бұрын
You suffer more than I and I'm in the floor with jack stands.
@Grumpyoldmechanic-l3r 16 күн бұрын
Some days yes I am sure.
@boriswilliams2729 19 күн бұрын
I have a question how you got the round nuts from the bushing bracket off how can I contact you?
@Grumpyoldmechanic-l3r 18 күн бұрын
When the welds broke I just used a pair of vice grips and some penetrating oil. It took a little bit of time. About 10 min a bolt
@boriswilliams2729 18 күн бұрын
@@Grumpyoldmechanic-l3rwhat specific type and size nuts did you put back?
@Grumpyoldmechanic-l3r 17 күн бұрын
@ I used the old round ones. I put a little penetrating oil in it. Then ran the bolt through a few times to clean the rust off. Then I installed them. I then re tack welded them on. Which is not needed but will help if you have to replace them again
@boriswilliams2729 15 күн бұрын
@@Grumpyoldmechanic-l3r do you know what size would work if I can’t fit the old ones back?
@Grumpyoldmechanic-l3r 15 күн бұрын
@ sorry I do not. I would say the best idea would be to take one of the bolts to the hardware store and match it up. My guess would be 14mmx1.5 or 1.0
@bittercamari 24 күн бұрын
how do I know when all the air is evacuated when I'm bleeding the brakes?
@Grumpyoldmechanic-l3r 24 күн бұрын
@@bittercamari you will get a steady drip. Also if there is still air you will see little bubbles coming out
@davidstarr6056 Ай бұрын
Mine was a Range designed for the 2021 5.3 with DFM. I have a lifetime power train warranty from my dealer, so I might as well enjoy the improved mileage from the DFM.
@Grumpyoldmechanic-l3r Ай бұрын
Life time power train warranty is amazing. I would definitely take advantage of That also.
@davidstarr6056 Ай бұрын
My 2021 5.3 with DFM had a lifter failure at 9000 miles. I had installed a device like you are recommending upon delivery of the truck. After GM repaired the truck, I removed the device.
@Grumpyoldmechanic-l3r Ай бұрын
That’s very odd. I think that may have just been a quirk. Although from what I have seen most of these say they are for not 2020 and up.
@marisbanana Ай бұрын
very well made video, thanks for making sure we could see what was going on :)
@Grumpyoldmechanic-l3r Ай бұрын
Glad you enjoyed it!
@rickhunter6479 Ай бұрын
LS the world
@Grumpyoldmechanic-l3r Ай бұрын
@@rickhunter6479 lol. I have an old transam with the lt1. I will do a video about it at some point
@petersavary8953 Ай бұрын
If I were going to go that far into that job, I would have put a new thermostat and a new fuel pump on. I would have kept the old fuel pump for a spare.
@Grumpyoldmechanic-l3r Ай бұрын
Did put a new thermostat in. And snuck a new aluminum radiator in. I work at a shop and didn’t have time to film all of it.
@michaelbarahona7871 Ай бұрын
Hey man, you rock. My actuator's pin position had popped out. Saved me from trading the crv in. Good vibes. Wife is thrilled to have the heat working again.
@Grumpyoldmechanic-l3r Ай бұрын
@@michaelbarahona7871 your welcome man
@agentcyborg8414 Ай бұрын
Thanks brother
@Grumpyoldmechanic-l3r Ай бұрын
@@agentcyborg8414 your welcome! Hope it helped!
@Npressv 2 ай бұрын
200k holy sh#$ that's the highest I've seen! Love this car 2 yrs and I still get excited to drive it!
@Grumpyoldmechanic-l3r 2 ай бұрын
He takes great care of it. Travels for work
@Bobbyroadhead 2 ай бұрын
So I just checked my heater hoses and someone took a hose u-bend and put it on both sides and plugged it. Where do those heater hoses lead to?
@Grumpyoldmechanic-l3r 2 ай бұрын
It sounds like maybe the heater core was leaking and they bypassed it to keep it from leaking coolant. So instead of the coolant flowing through the heater core it just loops around back to the engine.
@SakibAhsanTamim 2 ай бұрын
Hello, "Grumpy old mechanic" I was analyzing your channel and saw that in your channel have some problem, That's why your channel is not much growing and not getting much engagement, If you can solve these problems, Your channel will grow like a storm. If you tell I can tell these problems. Where can I tell? Here or email?