Can you recommend a video that demonstrates how to set up a 1050 properly, so that problems like this are avoided? TIA
@frijoli95792 жыл бұрын
So with this system you pre-prime your brass first?
@arturoceja83412 жыл бұрын
Where can I buy one ?
@ruebarb12 жыл бұрын
Thanks for Continuing to support the 1050 and the Ammobot. Where can I get spare parts for the Ammobot? Dillon completely erased any sign of it.
@Immortobot2 жыл бұрын
We have most parts available. Dillon has abandoned the entire original system. There are NO extractors available. Dillon owns the patent and refuses to make them for the original system.
@tittiger2 жыл бұрын
OK where the hell do I get this product?
@tittiger2 жыл бұрын
and where the hell do I purchase this? Kinda important don't you think?
@A.Mad.Lad892 жыл бұрын
The customer sounds like a dummy
@x14inchdubsx302 жыл бұрын
do you have some sort of automation for loading primers into the tube?
@snowgorilla97892 жыл бұрын
Nice to see you sticking up for your fine product
@arturoceja83412 жыл бұрын
When are they available? Can you send me the link so I can buy one please.
@tomsmythe32272 жыл бұрын
So, a year later and nothing but a blank page on the website? Not good!
@GCACok2 жыл бұрын
Great explanation.
@greg-judyjones89742 жыл бұрын
Would have been a lot easier to just communicate and ask for help first. Would have saved everyone time and money.
@GCACok2 жыл бұрын
Well designed. Very well designed.
@JohnJones-ew6io2 жыл бұрын
Nice work Mark.
@CryoToast2 жыл бұрын
Beautiful.
@RobActiveShooterEngh3 жыл бұрын
So will the waterfall sensor work on the older rectangular funnels? What about with the nylon block in the funnel for 9mm? For the older setups, looks like we just drill a hole for the speed control knob?
@Immortobot3 жыл бұрын
we don't have one with the square funnel to see if the waterfall fits the same space. The nylon block could not be used as it would block the sensor view...wouldn't be needed anyway.
@gopheros3 жыл бұрын
Nice:)
@laxman28093 жыл бұрын
Great product from a great company
@tonybeal51203 жыл бұрын
Is there anyway to still buy one of these?
@tonybeal51203 жыл бұрын
Is there anyway to still get one of these
@RobActiveShooterEngh3 жыл бұрын
Take my money!
@SeattleDudeSTI3 жыл бұрын
Awesome. I need one to feed hungry Rollsizer =) Please put me down for one.
@jimh35883 жыл бұрын
Very helpful video. Now that you have had time for tuning, which on (if either) would you recommend?
@Russell-13 жыл бұрын
Thanks for an Interesting presentation. As regards the two machines, I’m not overly impressed with either.
@sf77084 жыл бұрын
I just installed this kit on my case feeder, which has the old bowl. What’s not covered in this video are the screws attaching the old motor are longer than what is needed for new motor. You WILL have to shorten the screws to fit. Other than that, everything went together great! Now I can run my Rollsizer at full speed and not have to worry about the case feeder keeping up!
@HotReloads4 жыл бұрын
Running the RF100 too fast. Should be run at about half that speed.
@Immortobot4 жыл бұрын
This was an out of the box test. No tuning for a particular primer type.
@oldlyswansea4 жыл бұрын
so the case extractor insures that no 'bad' brass goes through the whole reloading process and ensures that only 'good' brass is used
@markpetersen9124 жыл бұрын
Have you looked into upgrading the hornady case feeder? Thanks for your ingenuity!
@RobActiveShooterEngh4 жыл бұрын
For some reason this video will not play properly. I've tried on my phone and on all 3 of my computers. The audio is fine but the video fails.
@RobActiveShooterEngh4 жыл бұрын
and now it works for some reason. I tried a dozen times and it wouldn't work, weird.
@PracticallySquared14 жыл бұрын
Cool video! Just what I was looking for. Keep up the good work brother.
@rene32614 жыл бұрын
thanks for the video your primerpro seems to run way better than mine did for 400€ the rf100 should get less than 0,2% upside down i think I might buy a second one from frankfort arsenal plus a 4 pack of tubes
@Immortobot4 жыл бұрын
That was out of the box with no attempt at tuning the speed. We can say that now we run it with no upside down, all CCI, which is our preferred primer.
@morpheus6d94 жыл бұрын
Metal or PLA
@morpheus6d94 жыл бұрын
If you have version 1 do you get a free upgrade ? 😎
@southronspirit4 жыл бұрын
were was the info on the ammo brass swage setters
@TallyWacker4 жыл бұрын
Thanks!
@myallstone4 жыл бұрын
could you make it so you could use two dillon case feeders
@bradmohr73984 жыл бұрын
The new variable speed case feeder does not have the High-Off-Low 3 position switch. It is only 2 position. How does this affect this upgrade?
@Immortobot4 жыл бұрын
We have an upgrade kit now available for the new case feeder that uses the Dillon motor. We also will make the original three position switch available for that that want to remove the Dillon components entirely.
@georgeharvey30624 жыл бұрын
Not sure I understand what the problem is with the Dillon case feed that it needs an upgrade? I just bought one but have not set it up yet. What problems should I be on the lookout for? Thank you
@smalltownrifleman3 жыл бұрын
@@georgeharvey3062 the Dillon feeders won’t feed fast enough to keep up with some of the new devices you may want to feed with it. If you are only using the feeder on your loader you will never need any upgrade.
@georgeharvey30623 жыл бұрын
@@smalltownrifleman my Dillon feeder is variable speed. I can’t crank fast enough to empty the feeder tube. Works great for me.
@smalltownrifleman3 жыл бұрын
@@georgeharvey3062 I know George, this is just for guys that are feeding some sort of a processing type machine. If you are just using it on a loader you are pulling by hand, you’ll never need an upgrade.