So how far did you get? I have one to fix as well. The gearbox shaft is a bit worn and the sheave that goes on it is a bit worn. All in all, too much. I can rebuild the hydraulics, but I don't want to spend a lot of money on it either.

How did you get the belt on?

Once I heard the dnb I knew it was gonna be fire video😅

I have same problem….i dont know my is cuting off sametimes

Hello! I recently acquired a 1000 mustang. Trying to take the clutch off now can’t get the inner part of the clutch off the motor it slides like an inch and that’s it. Any help? Thanks

I have a mustang 1200 and my rotary union went out. My rotary union is a dublin 1005-057-019 with a 1 " self locking nut fastened to the union. I called Dublin and other places no luck. I ended up using a nut and lock washer off of a ball on a receiver hitch on my pick up. It had the same threads and used a ratchet strap around the belt on the lower clutch and then around the inner half of the variable speed clutch and tightened it so that the belt was received on the variable speed clutch. Then I used a 3/4 inch end wrench on the outer part of the shaft coming out of the variable speed clutch and a 1 1/2 wrench to tighten the nut up till I compressed the lock washer. I did take my grinder with a cutoff wheel on it and trimmed an 1/8 or a little more so I could fit my 3/4 wrench on the end of the shaft. It makes it a single speed but has been working great. Hope this helps if your in a pinch like I was.

Good idea with the belt tensioner! I have an almost brand new Drive belt for an OMC 1200 machine for sale!

I’ve found from years of experience that cussing helps get the job done. Any job. 😂

Might you know if a RCK54-75 B mower rack will fit on a B5100e Kubota? I can't find the answer anywhere.

REDMAX EBZ8500 BACKPACK BLOWER

What size belt and pulley did you use? I have the same problem and have been searching desperately for an answer!

What size belt and pulley did you use? I have the same problem and have been searching desperately for an answer!

I just bought a 1000 and need some parts...can you please point me in the right direction?

Was riding there last weekend.

holy crap

I love mine but the parts are expensive

You can actually use the machine without the hydraulic connected. Just don't pull that lever unless you have that outlet plugged. Level ground only though. No breaks on the hills and put the sheive on Ridgid.

Finally somebody called it a clutch. If it won't disengage, you don't have breaks going down hill. The center pedal is for the breaks and kills the engine if the clutch won't disengage. Thank you for your video. Please keep doing them.

What did you use for a rotary union on the clutch?

Hi bro I have bobcat similar to your and I can’t find the parts for it cause the data plate is missing please can you help me thanks

Isn't there some kind of grounding thing you're supposed to do to discharge the electric? I have one of these from a thrift store with no instructions and recall something about possible electric shock and that you're supposed to do something before cleaning the blades?? Or no???? Anyone???

Your lucky

completely mute the music would be nicer

I just bought one today. Trying to get it on the trailer. Can't get it to cranm over or do anything jumped straight to the starter with a brand new battery. You know will these move easy while not running so I can winch it on a trailer?

Post

Me encanta ese tractor 👏🏼👌🏻 Es muy útil por su tamaño y potencia..

It is running too rich get your cylinder out and take the needle out and move it up at least one or two positions with your small clip

I'm seeing you couple similarities there between that and my Bobcat 610 I wonder if the clutch parts are interchangeable

Holy Christ was that thing ever tied down embarrassingly amateur & simply highly dangerous friggin small dollar store straps strung everywhere wrong dot would have loved to seen this.

Love the mustang 1200 they are a strong as machine I owned one and it had more muscle power then a brand new bobcat 953, the high n low range wen5 so I just pulled the pulley apart and put a big bolt through it and ran it on high but used throttle to vary the power..

Cool video just keep practicing with that bike you can hold the gears out a lot longer and need some practice shifting if that bike is really built you should be smoking him off the line and by the finish line he should be 20 yards behind you

I came to make sure I was doing this right and stayed for the comedy. 10/10 educational content.

Could you show how you made a mechanical tensioner please

You gotta break it in also it's got new piston n ring ,do your research

That thing sounds terrible ,put the air filter back on first

My brother had a bad habit of ironing his shirts with spray starch next to my 10 year old ionic breeze. Tried cleaning it but years of built-up starch killed it.

How much does the belt fo dor

How much u get it for

Eww. Stock exhaust

Never turn that quad around on the left side

You have a great excavator. First 16 I’ve seen with a hydro thumb. How do you like it, do you feel the need for a larger machine?

I got the Mustang 1000. Use it daily. Its probably 55 years old. Has the power of a bulldozer!

Terrible idea to run those (well any motor really) but especially these without an airbox!🤦 You can put a pw80 airbox on these so there not difficult to get

Please let me know if you know of anyone with one of these assemblies. Mine broke in two pieces. Any help would be appreciated

How many yards can you do with that?

Need some guy atv advice my fiancee wants aa 450R for christmas is it a difference between a 450R and a honda trx 250x? I found a trx 250x whats yal opinion

*update* truck has been sold

straight pipe? looking into a 4" for mine now and considering getting the kit w muffler... truck has a 4" straightpipe stack in the bed now and its too loud

Nice mini ex I bought the same one a week ago and it seems to be a good buy.......Im looking to put a thumb on mine

all that cussing....wow