aleks138

Пікірлер

@joshdavies6723 8 күн бұрын

yes

@rattlecan53 7 ай бұрын

Of all the places to crash at Barber, how did you manage to go down at the end of the back straight?

@aleks138 7 ай бұрын

It dug into the gravel

@rattlecan53 7 ай бұрын

@@aleks138 Yeah, I saw that. But what caused you to go off track? Just curious as i've never seen anyone run off back there on that side, only coming out of the chicane wide and running off to the left. As I said, no criticism just curious.

@aleks138 7 ай бұрын

Too much speed and not willing to commit to the corner. Normally I hit 120-130 on that straight but I got greedy with the pass and was in the 140s

@AwesomeYena 7 ай бұрын

I thought this video was made years ago.

@j.mcuisine7873 9 ай бұрын

wow its amazing and wonderful video of cat my dear nw frind. keep it up and stay blessed forever.

@Richnkids 9 ай бұрын

Looks to me that it might have backfired on that port forcing that flap over the divider, if you look close enough, it doesn't take much to cause that problem

@lisaperniciaro2207 9 ай бұрын

He’s a beauty!

@RoNiminal 9 ай бұрын

Stop abusing the poor animal, you psychopath. It's clearly uncomfortable. Plus, you shouldn't clip cats' claws.

@tonisnooker 9 ай бұрын

Beautiful Void & Beans

@harjasdhariwal5960 9 ай бұрын

Literally me

@vetiverose128 9 ай бұрын

he's like "hooman, look at ur nails! u need a clean up first!"

@joncothranphotography9375 9 ай бұрын

Looks like fun!

@Marcelo-wj9uu 9 ай бұрын

remova os flaps definitivo e verás como seu carro irá melhorar

@moriacolo6088 9 ай бұрын

hope you're good!

@zep2907 9 ай бұрын

damn 2008

@emolutioning 9 ай бұрын

the divider is likely installed wrongly. flip it the other way so that the flap will stop at it than BEFORE it as the vacuum from the actuator is supposed to stop at the precise position than before it. it springs over if made to stop earlier and ended up over and above the divider. theres another youtuber video who showed this divider position. it happened to mine which the flap pops over for both and pops out if divider stops the flap earlier. p2006 p2007 together.

@powasly6357 9 ай бұрын

yeah u need to put the flap open when u reinstall him

@Youngkenzus Жыл бұрын

I did a Pcv, thermostat, water pump job. I took that left intake manifold off but didn’t seat it correctly which gave me a P2006 code. So I had to go back and make sure the flaps were under the plates. Cleared the code now it’s driving healthy! Thanks for the video!

@TheAppleEnthusiast Жыл бұрын

Woww how does that happen?

@omegangel3368 Жыл бұрын

Such a throwback

@andyapple9 Жыл бұрын

The problem is a ribbon cable (4 wires) of gray color that go out near the STM32 to top main board with the 3 mosfets. Make sure this cable is seeded properly and there will be no issues.

@tagspayapa 2 жыл бұрын

What light bar did you use?

@aleks138 2 жыл бұрын

smile.amazon.com/gp/product/B081DTRC46

@eiknarf9993 2 жыл бұрын

Lol the lights are terrible. Whats size light bar?

@joncothranphotography9375 2 жыл бұрын

Go Bro!

@joncothranphotography9375 2 жыл бұрын

Cool!

@XFC8800 3 жыл бұрын

how much miles on the car?

@NickyyDubbs 3 жыл бұрын

What gauges are those?

@anzanz7497 3 жыл бұрын

2021

@rohitgodiwal7980 3 жыл бұрын

Whats the fix new intake???

@jalapep503 2 жыл бұрын

Take the rail off then push the flap down so it clears the stopper then set it in. Then it’ll be under the stopper once installed

@leepriestdoshapemontado 3 жыл бұрын

Really 4 gear?

@Skaude 2 жыл бұрын

Really seems so. + wet and one wheel peel. Requires as much as pulling 2nd gear on dry

@IT_Performance 5 жыл бұрын

This is perfect

@junaidgt90 5 жыл бұрын

Was the gearing sound normal when it was taking the TURN???

@aleks138 5 жыл бұрын

that was the cv axle

@zakdodgetattoos 5 жыл бұрын

What did the LED wire up to to show boot mode? I have pin 24 of the 29f800BB grounded through a 1k ohm resistor but I can’t get it into boot mode and I can’t figure out if I’m in boot mode. Ecu is bricked, just trying to practice with a spare ecu to be sure I can fix the issue if/when it arises

@aleks138 5 жыл бұрын

pin 66 but it wasn't 100% reliable 0v- normal 3.5v- bootmode I never used a resistor. just directly to ground.

@KBMOTORSchannel 4 жыл бұрын

Not a bootmode indicator, merely just a power light. It comes on when you attach power to the Ecu. I’m all over nefmoto trying to figure out how to build the bench harness. I can’t find it!!! I’ve read it 10 times. Now I want to build it and find nothing