Halo, salam dari Indonesia 🙏🙏. Saya mempunyai kit scx10ii , motor menggunakan fusion SE. Apa yang terjadi jika Gandar hadapan menggunakan 24/8 dan belakang 24/8? Adakah ia akan merosakkan fusion saya? 24/8 depan belakang kit boleh berjalan dengan smooth? Terima kasih 😁😁😁😁

So , servo motor dont need esc?

Where do they sell the 6×6 I have the mn86ks 4×4

Kaayasag backgroundmusic

Ciao. Si può usare con un potenziometro? Grazie

The top one is a COPY

Thanks ❤❤😊😊😊😊👍

Hernandez Ronald Hernandez Daniel Lopez Betty

How long is the pull link steering from the servo to axle?

link to purchase tires and 7mm m3shaft

2 years later and this video is still helpful new to the hobby but i managed to hit lines i couldn't hit before 👍

Esse receiver pode conectar qualquer outro controle?

Brp panjang linkage depan (atas dan bawah) broo??

...and now you have bump steer: with every uneven bump the front axle takes, the steering will turn automatically.

Guy didn't Evan do anything the fuck

Cual es el link para comprar ese motor?,gracias

Apa Fungsi overdrive slain ban depan lebih cepat?

How well holds up the gearbox after a year of use ?

What is Cherokee chassis made of? Plastic or metal?

I have found a smaller brushless motor that should fit, the D2225, 22mm diamter by 25mm long so no need to cut the chassis, but it is not as powerful however, 80W/11A under load as per the specs

Also, from my math (TIL P for pitch is the imperial measure of module), so if stock pinion is 10t 7.2mm, it's 0.6mod or 42p, 32p would skip or be noisy, no?

How is the speed and torque? I plan on using 10t, same as stock (I found a 10t 0.6m pinion on AliEx) for 1:18 reduction with 1400kv motor, I did the math for your setup and you have 1:11 reduction and an output of 600 RPM with 2s whereas 1400kv with 10t will output 570 RPM, so about same speed as your setup, stock I think its about 470RPM (8500 RPM motor?)

share spec bossku. mcm panjang linkages. motor outrunner tu saiz apa bosku

Are they both locked rear differentials

bro does this axle support counter rotation? means front and rear axle shaft rotate in different direction to eliminate torque twist.

Good video, will this setup accept a 540 size motor?

Great video, do you have a running video of this, and what body did you use and how did you Mount that body?

Is the v2 always on 60watts power?

kyrc no need binding setup with remote?

Hello....I connected the ESC to 2nd channel....but my motor not turning why???

Hello friend, how do you power the servo this way? How do you power the servo if you remove the positive? thank you

Great machines. Water+mud=fun 😉🤣💪

kalau tetep pakai per luar gimana? bakal merubah sesuatu gak? atau pakai 2 shock aja? 1nya shock biasa, 1 nya lagi pake drop shock?

what if i keep using external spring? does it change something? or should i just use 2 shocks? 1 normal shock and 1 dropshock? need your response. thank you

can you do for this chassis a 2 speed mode like other crawlers ? or something to adjust the speed lower and higher ?

Sebelum ny apakah harus flashing firmware, atau langsung connect ke arduino dan config

Bang bisakah accelerator diganti pake servo

Axle nya sudah portal itu Bang?

will the bec run batt down when not running?

Ok so im new to this but what will this do? Make it faster? Smoother????

I just did the same exact thing to a set of cheap internal spring shocks, the cool thing about these friction shocks you can quickly swap different springs without getting oil everywhere.

Bang nak tnya..wheelbase untuk body hilux ni brapa?

Hi clearance links don't work properly if now you hit the rocks with the transmission, so much money spend in hop ups better get at once a Gmade

Assalamualaikum bang saya nak tanya ni kenapa axle depan saya tak bergerak? Tapi takda benda patah😢😢😢

Hello! You might also be interested in this as an alternative: kzbin.info/www/bejne/imrUdqR_iqeSf6s

You should do a full driving video :D

Why you not look the gear servo? Plastic or metal

Lose the music...talking would be nice.

same process for Am32?

И чем всё закончилось???