I really appreciate your knowledge sharing

I think thats whats up with mine thanks for the video .

I keep trying to unstick my Ford starter. NO LUCK.

Your telephone number for M&M tractor no longer works

Where do you spray it

I have this same carburetor on my 1930 model A and having the same issues. Can you tell me what the adjustments should be?

Hard starting has been an issue for some time with my front mount 8N. After watching this video I was pretty excited when I saw I had the Autolite 437 installed. I replaced the 437 plugs with the Autolite 216 plugs and it fired right up. Thanks so much for this video.

Just to confirm if you could, my 1952 *N side mount is best served with an Autolite 216, correct? THUMBS UP!!!

Thank you! This information is greatly appreciated.👍

Was pulling out what little hair I have left trying to figure out why gas was running out of the intake. Thanks a bunch!!!

Thanks, great video!

Ok! my carb leaking gas from front. Purrs like a kitten only with choke three quarter engaged. Am going to try this. Everyone tells me it is starved for fuel so must check adjustment of float. Don't know the specs for this but hopefully will figure it out. Can't be by trial and error. Am sick and tired of taking this carb off and on. 1966 IH 606 with original odd duck carb.

maybe could also use a pane of glass with emery cloth laying on it

Just bought a JD 302A tractor with loader and the 10 th time I shifted the left side high low it got stuck. You advised what I was thinking just attempt to see if I can find a new shifter rod or whole assembly. Long time no see how your doing well these days M..

I can't find flat spots in my shop either.

I have a Long 310. I have done what you show us in this video, plus I replaced my pump. Still the 3 point only, slowly, goes up when the tractor is at full throttle. But only will go up a couple times. Do you have a video of re doing the lift cylinder?

Im dealing with these issues on my 801 cant find where its comming from it doesnt seem to leak when its running only when it sits with the tank valve left on

Yoooooou nearly hit the truck 😅

What fluid are you testing?

Man i was fighting my 445 I just bought for hours to day trying to fix this issue best video on these tractors i found

Thank you so much for putting together this video, my dad has a long 510 but I don't know the year of it and he had to change out the lift arms piston but I don't know why. He passed away in 2008 and my father in-law also has a long 510 and it will not lift up very high and if you put your weight on it while trying to lift it it squalls so I think his piston seals are gone ? I noticed in this video you didn't mention that part, what do you think about that. Thank you again, I can't find any info on long tractors and never knew about UTB tractors or long brand being part of that line up.

I am looking at a Ford 550 backhoe and the backhoe itself will only swing left and right maybe 10° what can be causing that.? Just buying it to do some digging around my 40 acres digging up stumps and whatever if I buy it, but I’d like to find out what it would cause that problem.

Im working on a 2610 Long. With your video, i got the 3 point to start working again but now it bounces really bad when going down. Any ideas ?

Thakns for this video it save me a day of production

That is great, I'm having that exact issue and will try this in the morning!

MF 135 probably 60s or 70s model. Perkins 3 cylinder diesel. Hung in one gear, I think third. Can’t get in reverse either. Prior to fatal accident one year ago, deceased brother in law, we think he said it wouldn’t go into 2nd. Never said anything about reverse issue. It sat in field next to accident site for a year before I decided to go get it working again. Did and drove it carefully for about 1/2 mile in whatever gear it was locked in. High/low works and replaced hydraulic fluid Saturday and got lift working. Need all gears and especially reverse working. Property needs major bush hogging. Saw some vids suggesting use long screwdriver in fluid entry hole to pry over a gear. Your thought please sir. Learning a lot but new to me. Any help appreciated

I will try your stuck valve theory on my 1986 Long 2360. My three-point hitch was working before and after working on my control valve manifold, the hitch will not go up or down as if there is no hydraulic pressure. I did add hydraulic oil to the reservoir because it was way low. I can pick up the three point levers in the back and the arms go up and down easily. Just dead! I hope there is nothing too seriously wrong. Is there such a thing as removing air form the hydraulic system

5.4 3 valve sounds like a ticking time bomb its in the name 😂

I’ll take pushrods any day 😂

My 550 backhoe transmission will work Forward and reverse only for about 45 seconds. Then I have to wait for about an hour for it to cool down and then it will work again. Any tips?

Thank u sir

That blowby amount is perfectly fine.

Good video !! IS THERE A DIESEL THATS GOOD ?? I hope u answer this maybe someone will .

Ford 555 drives forward and reverse just that it's the opposite lever position And when drive on the road sometimes the tractor will almost stall and if you put it in neutral will start drive in the opposite normal direction of travel

Hear the animals in the background. Where are you?

What are you killing? I thought it was about home squatters.. until you said wings.

I dont understand why people still drive these things

The 6.4 is known for pushing a lot of vapor of out the oil fill cap. As long as there isn't pressure behind it, you're fine....for now. The 6.4 is still a money pit.

Easier than a failed lifter. A one day job...get it done.

I have 210,000 on my 2009 and have never had a problem. Thank You Jesus!🙏🫶🏻

This is why you keep it NA

Pretty sure the float bowl zone doesn’t matter as fuel level doesn’t get anywhere near there with an operating needle stopper in the fuel inlet and the Venturi center makes that an air chamber anyways so might run a touch rich if anything, and updraft motors should be rich. Outer edges matter if you care that much but draft is pulling air inward so not much getting out that high. Gasket seals imperfections between the two and the brass gas drip balls for a ford, screen for continental and others at the bottom is going to leak both directions anyways.

Possibly more travel distance on the shafts. Or one operation requires less oil pressure

The only reason I could think of would be if there was an engineering redesign requirement for one of the sides. This would allow them to change one and keep the opposite side intact. Also, no need to update any part reference documentation.

Different seal

Internal spring

Bendix jak już

My number 1 problem fixing engines was always assuming parts made straight, stayed straight...

Needs a new return spring seams like. Every starters different so i could be wrong. I used to work for A&S Ignition in Patterson N.Y used to deliver arts for them all iver new york it was an awesome job to have and i learned a little bit while i was there driving.

Sorry but whst is the purpose of this?