Yes

How. Much. Price. Sir

@@girijasudhakaran8760 it's depend on your gear size & number of teeth.

36. Theeth. ​@@ajaymixup4396

Mill Jaye ja sir ji bananeko costly girta hai.

Use wd40 overnight

Yes sir.

Yes

Yes 👍

Where did you find it?

@@audacityhour3104 It probably is brass, or at least some other similar alloy, as trying to machine pure copper is more difficult. You should be fine with those. Match your gear width, height, and tooth count.

@@audacityhour3104 What makes steel so bad, is that it's like putting a machinist cutting tool into contact with the softer aluminum of your hub motor. Guess the one that will win.

@@audacityhour3104 I'm working with Bafang (8-fun) BLDC hub motors. The outer case IS the ring gear. 😂 But this is good, because being in contact with outside air allows them to cool very well. Whatever your setup, you wouldn't want steel riding steel, as this causes [Fe] bits wear off and get stuck between magnets and stator or sensors. Non-[Fe] type metals won't do this. Plus they will conduct heat, instead of holding heat. Last, you will want to remove old grease, and replace with an all-weather aircraft grease. It will stay where you put it and not become stiff in cold.

Outer casing gear hardness 50-55 hrc . Others gear hardness maximum 20 hrc. How to damage outer casing gear?

@@ajaymixup4396 Bafang (8-fun) outer gear is aluminium. Steel cuts aluminium. Case closed!

No sir using outer gear hardness 50-55 hrc & other gear ms metal no hardness.

Yes

Good idea.

I upgraded mine 5 years ago still going fine and with a 52v battery and 1500w controller and sounds the same

I was thinking brass too lol :P

What about copper? I found copper Where did you find brass?

Dada gear pele janaben kolkatar kothay paowa jabe

Please check Amazon

How about bronze or brass?

I upgraded mine 5 years ago still going fine and with a 52v battery and 1500w controller and sounds the same

I know right ?? Its " stupidity " in its purest form .

@@RandomClips27. what motor? im currently on geared motor with default nylon planetary geras inside with controller 48v 22a max and 11a continuous, im thinking to put steel planetary gearings inside and put on controller with 30a max/15a continuous, would that work, is that what you have done and it works fine for 5years now?

In my case outer gear hardness 50-55 hrc & other gear non hardness ms metal. How to damage outer gear. If damage outer gear i can change it. It's also removeble.

It's not about the 4$. It's about the time it takes to replace it. And the inconvenience at the moment it breaks.

Yeah , well , you can change the nylon gears and the motor will run . Those steel ones will do for a while , but they will chew up the teeth on the hull . That means buying a new wheel later on 😑.

I don't think the outer ring gear is aluminium tbh, it's probably harder than the cast iron/mild steel billet he used to cut the gears. I think others have good reliability with soft metal gears. Lasts a lot longer as an over package in the rough terrain of the sub continent.

@@oneman29 *The bicycle wheel "hub" I'm pretty sure is aluminum. The inside of the the wheel hub has "teeth" that the four "sprockets" ride in. He talks about removing the four nylon gears and replacing them with steel gears. The aluminum was stronger than the nylon gears but not as strong as the steel gears. Those steel gears will chew the aluminum wheel hub up if they fail.*

I upgraded mine 5 years ago still going fine and with a 52v battery and 1500w controller and sounds the same.

@@RandomClips27. the steel gears don't damage my engine then ?

@@charliesgrumma5388 it's steel. I have rust around the area where the bearing is. If it was aluminum it wouldn't rust. Therefore, the hub casing that has teeth which latch into the planetary gears are steel.

Lite sound ayega.

Coming soon.

No

Outer frame me Aluminium ka teeth nahi hote, metal ka ring with hardness wala gear hota hai sir ji, hardness (50/55 hrc) gear k sath agar non hardness metal ka gear lagaya jaye to non hardness wala gear sab se pehle kharab hoga. Our aap ko pata hoga metal ka without hard wala gear kharab hone ko minimum 10 years to lag hi jaye ga. Thank you.

Your mobile no

Bana ke lena padega. Readymade nahi milega.

Sir mujhe bhi jarurat hai iski Kya aap bechte hai

You can buy them preassembled on eBay for like $20

@@halo3pownage the ones on Ebay aren't metal

@@ahmadzaki3328 the price ranges from $20 for the gears alone to $32 for the clutch assembly with metal gears prepressed on

@@ahmadzaki3328 if you're actually looking at swapping to metal gears though you need to look into getting proper lubricant for the motor because pure metal gears will cause more damage to the motor in the long run due to metal shavings. There's a reason why there are nylon gears. It's all a trade off and it depends on what your end goals are though because metal gears will transmit torque way better than nylon gears will but from a longevity standpoint nylon gears will cause less damage to the actual motor itself then metal gears will